... the front teeth and The rear sprocket has 16 teeth If the speed of the front sprocket is 60 rev/min, the speed of the rear sprocket is 120 rev/min Therefore: Speed of rear sprocket Speed of = ... Figures 2.5 and 2 .6 HOCHIMINH UNIVERSITY OF INDUSTRY Bikes have a sprocket and chain system The number of teeth on the sprockets is very important On the sprocket has 32 bike in Figure 2 .6, the front ... slower speed teeth C than A, so g) B has a greater number of teeth than A; the speed of B is therefore Slower than A HOCHIMINH UNIVERSITY OF INDUSTRY Practice Choose a, b, c, d or e to complete...
... Read the instructions for changing a tyre; then put them in the correct order Practice Read the instructions for the dynamo belt on the left; then complete the instructions for the alternator belt ... working volume + clearance volume) by the clearance volume Therefore, for the engine in figure 4.2: ( _ + ) / _ = The engine therefore has a _ : _ compression ratio ... Presentation Select the correct instructions for the actions in Figure 4.1: For example: A = Turn the jack handle anticlockwise to lower the car Turn the gear...
... ENGLISHFORAUTOMOBILEENGINEERINGUNIT FINDING A FAULT IN A CAR MAY 14, 2011 HOCHIMINH UNIVERSITY OF INDUSTRY Presentation ... the key, the starter motor may be jammed If it is, you can try to release it by pushing the car forwards and backwards (in 2nd gear) If the car still doesn’t start, the starter motor should be...
... ENGLISHFORAUTOMOBILEENGINEERINGUNIT www.fme.edu.vn HOCHIMINH UNIVERSITY OF INDUSTRY FACUTY OF MECHANICAL ENGINERRING INTRODUCTION The automobile industry is a fast ... the first automobile was put on road, this industry has developed tremendously Now there are thousands of factories all over the world manufacturing numerous type of automobile The automobile ... great demand for varied types of automobile products, vehicles and engines HOCHIMINH UNIVERSITY OF INDUSTRY FACUTY OF MECHANICAL ENGINERRING INTRODUCTION There is also a great demand for trained...
... system C tracer controlled D NC controlled unitunit 95Mechanism is a component of machine that transmit or change A force B effort D movement C motion 96 Parts which have teeth that can engage ... are available in many form sheets, tubes, robs A such C so D so that B such as 65 Plastics have to atmospheric corrosion A resist B resistant D resistion C resistance 66 Thermoplastics will ... shape B for shape C for shaping D both A & C 37 Levers.according to the relative positions of the load, the effort and the fulcrum A classify B is classified C are classified D classified 38 A force...
... Thi Bich Ngoc D06K52 Faculty of Foreign Language Ha Noi University of Technology The Situation of Learning Englishfor Electrical Engineering of D06k52 Students in Faculty of Foreign Language, ... easily Le Thi Bich Ngoc D06K52 Faculty of Foreign Language Ha Noi University of Technology Results The course requirements in textbook of Englishfor Electrical Engineering: Before the lesson - Students ... textbook of Englishfor Electrical Engineering, FOFL’s students have to consolidate and prepare the lesson at home before going to school Furthermore, there is a fact that although students in D 06 have...
... system C tracer controlled D NC controlled unitunit 95Mechanism is a component of machine that transmit or change A force B effort C motion D movement 96 Parts which have teeth that can engage ... are available in many form sheets, tubes, robs A such B such as C so D so that 65 Plastics have to atmospheric corrosion A resist B resistant C resistance D resistion 66 Thermoplastics will ... shape B for shape C for shaping D both A & C 37 Levers.according to the relative positions of the load, the effort and the fulcrum A classify B is classified C are classified D classified 38 A force...
... Mechanical Engineering The thesis studies the English – Vietnamese translation of terms in the materials for Mechanical Engineering First, the thesis collects and groups English Mechanical Engineering ... especially translation in mechanical engineering, dictionaries editing, English language teaching as well as for the standardization of Vietnamese mechanical engineering terminology ... out common translation strategies which can be applied in the English- Vietnamese translation of terms in materials for mechanical engineering Hopefully, the result of the study would be useful...
... 64 .9 15 .6 1.4 3.0 0 .67 22.1 55.8 22.1 2.8 0 .63 7.8 28 .6 41 .6 22 22 37.7 27.3 professional technical words b Guessing the meaning of words from the contexts c Finding the appropriate meaning for ... in reading Englishfor EEE and present some useful techniques for improving teaching and learning Englishfor EEE In order to find out the problems in teaching and learning Englishfor EEE, a ... used recently ESP at VTTTU includes Englishfor Technical Engineering , Englishfor Electrical and Electronics Engineering and Englishfor Computer Science” The ESP textbooks were designed with...