0

khóa đào tạo tính toán ổn định và ứng dụng trên phần mềm psse cho kỹ sư hệ thống điện

Phần 5 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Lựa chọn bộ kích từ trong mô phỏng ổn định và mô hình kích từ trên Phần mềm PSSE)

Phần 5 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ HỆ THỐNG ĐIỆN (Lựa chọn bộ kích từ trong mô phỏng ổn định mô hình kích từ trên Phần mềm PSSE)

Điện - Điện tử

... values E1and E2shouldThe field voltage values E1and E2 should normally be chosen near the knee of the exciter’s magnetization curve and near the exciter ceilingeBook for...
  • 125
  • 794
  • 8
Phần 25 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Kịch bản nghiên cứu theo tiêu chuẩn IEEE trên Phần mềm PSSE)

Phần 25 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ HỆ THỐNG ĐIỆN (Kịch bản nghiên cứu theo tiêu chuẩn IEEE trên Phần mềm PSSE)

Điện - Điện tử

... frequency relays (loads and t)generators) Prepare for transient simulation and choose the following channelschoose the following channels Machine anglesBus voltageBus voltage ... voltage relays (loads and t)generators) Prepare for transient simulation and choose the following channelschoose the following channels Machine anglesBus voltageBus voltage ... the PV Analysis window and create thecreate the distribution factor file• Make sure to choose the right settings• Select the source and sink subsystemseBook for You10IEEE 24–QVANALYSISIEEE...
  • 39
  • 532
  • 7
Phần 10 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Ngồn ngữ mô hình hóa hệ thống điện trên Phần mềm PSSE)

Phần 10 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ HỆ THỐNG ĐIỆN (Ngồn ngữ mô hình hóa hệ thống điện trên Phần mềm PSSE)

Điện - Điện tử

... tie lines connected to the external system and find the new short-circuit le ellevel The chosen value for the equivalent machine base is 4000 MVA. This will represent the contribution...
  • 88
  • 776
  • 8
Phần 12 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Ứng dụng Ổn định quá độ trên Phần mềm PSSE)

Phần 12 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ HỆ THỐNG ĐIỆN (Ứng dụng Ổn định quá độ trên Phần mềm PSSE)

Điện - Điện tử

... data of this dynamics file to the already existing data• So in this case, choose the dynamics data file optioneBook for YouRunning the system before any faults29RUNNING ... Go to the Power Flow menu, Reports, Area / zone based reports• Select Inter area / zone flow, choose output for all areas and click on Go• We can see the total generation, load, reactive compensation,...
  • 69
  • 513
  • 9
Phần 13 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Các tính toán phân tích sự cố trên Phần mềm PSSE)

Phần 13 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ HỆ THỐNG ĐIỆN (Các tính toán phân tích sự cố trên Phần mềm PSSE)

Điện - Điện tử

... FaultSinglePhasetoGroundFault021021Z+Z+ZE3=I=I=I0=I=I0=VCBAPhasetoPhaseFaultEIIPhasetoPhasetoGroundFault02E)Z+Z(0=IZ+Z=I‐=I021210100221021EZ‐=IZZ+ZZ+ZZ)(=I201002212EZ‐=IZZ+ZZ+ZZ=I1002210ZZ+ZZ+ZZeBook for YouZERO SEQUENCE TRANSFORMER 15CONNECTIONSWARNINGNOTICE00H LTYg YgHLPSSEX0H‐NNX0L‐NX0TNDTRg3RgX0T‐NH L3Rg X0H‐NNX0L‐NTX0T‐NCORRECTMODELeBook...
  • 21
  • 543
  • 7

Xem thêm