MPLS Lab Configuring Frame Mode MPLS
Tài liệu Configuring Frame Mode MPLS doc
... Layer frame before sending it across one of many supported Layer media At the next MPLS- enabled Label Switch Router (LSR), the MPLS frame is read and the IP packet is switched as an MPLS frame ... Verify MPLS Configuration MPLS has many show commands that you can use to verify proper MPLS operation Issue the show mpls interfaces command to see a quick summary of interfaces configured with MPLS ... traffic engineering MPLS runs between Layers and of the OSI model and, because of this, is sometimes said to run at Layer 2½ The MPLS header is bytes long and includes a 20-bit label Configuring the...
- 12
- 244
- 0
Tài liệu Lab 5.2.1 Configuring Frame Relay doc
... configuration lab Step Configuring the serial interface a In Frame Relay, the customer router is considered the DTE device In order to configure the serial interface the Layer Frame Relay frame type ... configure the frame type, use the following commands: Cork#configure terminal Cork(config)#interface serial Cork(config-if)#encapsulation frame- relay IETF b Next the format of the Frame Relay management ... type, use the following commands: Cork(config-if) #frame- relay lmi-type ansi Cork(config-if)#no shutdown Cork(config-if)#end Step Verifying the Frame Relay configuration a To verify the configuration,...
- 5
- 594
- 1
Tài liệu Lab 5.2.2 Configuring Frame Relay PVC doc
... configuration lab Step Configuring the serial interface First, define the Frame Relay frame type to be used on this link To configure the encapsulation type, use the command encapsulation frame- relay ... Dublin(config-if)#description PVC to Washington, DLCI 102, Circuit #DASS465866 Contact Pat White (091-6543211) Step Verifying Frame Relay PVC a On the Washington router, type the command show frame- relay pvc: Washington#show ... Setting up the Frame- Relay Map a When sending an Ethernet frame to a remote IP address, the remote MAC address must be discovered, so that the correct frame type can be constructed Frame Relay needs...
- 6
- 387
- 0
Tài liệu Lab 5.2.3 Configuring Frame-Relay Subinterfaces doc
... Berlin(config-if)#encapsulation frame-relay ietf Berlin(config-if) #frame-relay lmi-type ansi Berlin(config-if)#description Circuit #DTK465866 Berlin(config-if)#no shutdown Step Create subinterfaces on the ... address 192.168.5.1 255.255.255.0 Amsterdam(config-if) #frame-relay interface-dlci 103 Step Create subinterfaces on the Paris router To configure the subinterfaces on the Paris router, use the following ... address 192.168.6.1 255.255.255.0 Paris(config-if) #frame-relay interface-dlci 203 Step Create subinterfaces on the Berlin router To configure the subinterfaces on the Berlin router, use the following...
- 7
- 503
- 1
Tài liệu Lab 5.2.5 Configuring Frame Relay Subinterfaces pdf
... the PVC Step Show the Frame Relay maps a Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b What is the ... 192.168.3.0 192.168.5.0 192.168.6.0 Step Verifying Frame Relay PVC a On the Amsterdam router, issue the command show frame- relay pvc: Amsterdam#show frame- relay pvc b How many active local PVCs are there? ... Berlin(config-if)#encapsulation frame- relay ietf Berlin(config-if) #frame- relay lmi-type ansi Berlin(config-if)#description Circuit #DTK465866 Berlin(config-if)#no shutdown 2-7 CCNA 4: WAN Technologies v 3.0 - Lab 5.2.5...
- 7
- 469
- 2
Quản trị mạng Lab 10 - Frame relay
... Router3(config-if) #frame- relay map ip 192.168 .100 .2 302 broadcast Router3(config-if) #frame- relay map ip 192.168 .100 .1 301 broadcast Router2(config-if) #frame- relay map ip 192.168 .100 .3 203 broadcast ... ip 192.168 .100 .3 203 broadcast Router1(config-if) #frame- relay map ip 192.168 .100 .3 103 broadcast Router1(config-if) #frame- relay map ip 192.168 .100 .2 103 broadcast Test the IP connectivity between ... lệnh frame- relay map để map tới router khác Đối với router point-to-point: cần vào subinterface point-to-point dùng lệnh frame- relay interface dlci để gắn tĩnh dlci cho subinterface End of lab 10...
- 4
- 561
- 7
Tài liệu Configuring Frame Relay doc
... configuration lab Step Configuring the serial interface a In Frame Relay, the customer router is considered the DTE device In order to configure the serial interface the Layer Frame Relay frame type must ... configure the frame type, use the following commands: Cork#configure terminal Cork(config)#interface serial Cork(config-if)#encapsulation frame- relay IETF b Next the format of the Frame Relay management ... type, use the following commands: Cork(config-if) #frame- relay lmi-type ansi Cork(config-if)#no shutdown Cork(config-if)#end Step Verifying the Frame Relay configuration a To verify the configuration,...
- 5
- 305
- 1
Tài liệu Configuring Frame Relay PVC pdf
... Dublin(config-if)#description PVC to Washington, DLCI 102, Circuit #DASS465866 Contact Pat White (091-6543211) Step Verifying Frame Relay PVC a On the Washington router, type the command show frame- relay pvc: Washington#show ... no Frame Relay switch in this configuration and consequently no Frame Relay DCE: Washington#configure terminal Washington(config-if)#interface serial Washington(config-if)#encapsulation frame- relay ... Setting up the Frame- Relay Map a When sending an Ethernet frame to a remote IP address, the remote MAC address must be discovered, so that the correct frame type can be constructed Frame Relay needs...
- 6
- 255
- 0
Tài liệu Configuring Frame-Relay Subinterfaces pdf
... Berlin(config-if)#encapsulation frame-relay ietf Berlin(config-if) #frame-relay lmi-type ansi Berlin(config-if)#description Circuit #DTK465866 Berlin(config-if)#no shutdown Step Create subinterfaces on the ... address 192.168.5.1 255.255.255.0 Amsterdam(config-if) #frame-relay interface-dlci 103 Step Create subinterfaces on the Paris router To configure the subinterfaces on the Paris router, use the following ... address 192.168.6.1 255.255.255.0 Paris(config-if) #frame-relay interface-dlci 203 Step Create subinterfaces on the Berlin router To configure the subinterfaces on the Berlin router, use the following...
- 7
- 275
- 0
Tài liệu Configuring Frame Relay Subinterfaces pptx
... the PVC Step Show the Frame Relay maps a Look at the frame relay maps by typing the command show frame- relay map at the privileged EXEC mode prompt: Amsterdam#show frame- relay map b What is the ... 192.168.3.0 192.168.5.0 192.168.6.0 Step Verifying Frame Relay PVC a On the Amsterdam router, issue the command show frame- relay pvc: Amsterdam#show frame- relay pvc b How many active local PVCs are there? ... Paris(config-if)#no shutdown Berlin(config)#interface serial Berlin(config-if)#encapsulation frame- relay ietf Berlin(config-if) #frame- relay lmi-type ansi Berlin(config-if)#description Circuit #DTK465866 Berlin(config-if)#no...
- 7
- 208
- 0
Cisco Systems - Configuring frame relay doc
... ICND v2.0— 8-8 Verifying Frame Relay Operation Router#show frame- relay traffic • Displays Frame Relay traffic statistics Router#clear frame- relay- inarp • Clears dynamically created Frame Relay maps, ... v2.0— 8-3 Configuring Basic Frame Relay © 2002, Cisco Systems, Inc All rights reserved ICND v2.0— 8-4 Configuring a Static Frame Relay Map © 2002, Cisco Systems, Inc All rights reserved ICND v2.0— 8-5 ... Frame Relay DLCIs and the LMI Router#show frame- relay lmi [type number] • Displays LMI statistics Router#show frame- relay map • Displays the current Frame Relay map entries Router#show frame- relay...
- 17
- 467
- 0
CCNA lab books frame relay
... 6/8 CCNA Lab Book version Phiên tiếng Việt VDC Training Center Trang 7/8 CCNA Lab Book version VDC Training Center e Kiểm tra Frame- Relay mapping Router, ý trạng thái DLCI active f Thực debug frame- relay ... nối môi trường thực hành a Cấu hình Frame- Relay Switch - Chuyển Router sang Frame- Relay switch (FRS) - Chuyển encapsulation interface serial sang dạng Frame- relay, ý interface FRS phải DCE - Cấu ... ta kiểm tra lệnh “show frame- relay pvc” Phiên tiếng Việt Trang 3/8 CCNA Lab Book version - VDC Training Center Chú ý rằng, PVC có trạng thái INACTIVE, chưa cấu hình Frame- relay Router đầu cuối...
- 8
- 686
- 6
Configuring Frame Relay docx
... Connectivity Step Verify the Frame Relay network After configuring Frame Relay on all routers, verify the Frame Relay configuration on R1 a Issue the show frame- relay map command on R1 to verify ... Configure Frame Relay and Default routing on the Spoke Routers Step Configure the Physical Frame Relay Interface on the spoke routers Just as we configured the hub router for Frame Relay, the ... Status Timeouts 16 c Finally, issue the show frame- relay pvc command on R1 R1# show frame- relay pvc PVC Statistics for interface Serial0/0/0 (Frame Relay DTE) DLCI = 102, DLCI USAGE = LOCAL, PVC...
- 5
- 234
- 1
MPLS Curriculum— Lab Setup Guide
... Lab Setup Guide Follow these steps to set up the laboratory for MPLS Curriculum exercises: n Wire the laboratory equipment according to the setup specified in the MPLS Curriculum Management Guide ... switch MPLS_ WAN_Switch.t xt n Download the initial configuration to the routers inside the workgroup, named A1, A2, B1, B2, PE1, PE2, PE3, PE4 and P (see MPLS Curriculum Management guide for lab...
- 2
- 295
- 0
Tài liệu Cisco MPLS based VPNs: Equivalent to the security of Frame Relay and ATM docx
... Introduction Today, business customers accept the level of security that Frame- Relay and ATM offer as layer VPNs, however they might have concerns about the level of security that an MPLS based VPN offers ... with the CE routers there are mechanisms in place to limit the impact of DoS attacks to the VPN where they originated Which equates to the way these attacks are handled in Frame- Relay and ATM based ... What the next sections concentrate on is how MPLS based VPNs compare to Frame- Relay and ATM FrameRelay and ATM are well known in the industry and have the reputation as being secure In order to...
- 15
- 509
- 0
Từ khóa: 10configuring frame mode mplsimplementing frame mode mplslab 34 frame relay pointtopoint subinterfaceactivity configuring frame relay point to point subinterfacespacket tracer configuring frame relay pointtopoint subinterfacespacket tracer configuring frame relay pointtopoint subinterfacesconfiguring frame relayand subinterfacesconfiguring frame relay with subinterfaceskiểu khung frame modehướng dẫn cấu hình mpls lab7200—uniform mode mpls diffserv tunneling7600—uniform mode mpls diffserv tunnelingsánh tính bảo mật của mpls vpn với atm frameconfiguring an mpls vpnmạng mplsBáo cáo thực tập tại nhà thuốc tại Thành phố Hồ Chí Minh năm 2018Nghiên cứu sự biến đổi một số cytokin ở bệnh nhân xơ cứng bì hệ thốngchuyên đề điện xoay chiều theo dạngNghiên cứu tổ chức pha chế, đánh giá chất lượng thuốc tiêm truyền trong điều kiện dã ngoạiNghiên cứu tổ chức chạy tàu hàng cố định theo thời gian trên đường sắt việt namBiện pháp quản lý hoạt động dạy hát xoan trong trường trung học cơ sở huyện lâm thao, phú thọGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitNGHIÊN CỨU CÔNG NGHỆ KẾT NỐI VÔ TUYẾN CỰ LY XA, CÔNG SUẤT THẤP LPWAN SLIDEPhát triển du lịch bền vững trên cơ sở bảo vệ môi trường tự nhiên vịnh hạ longTìm hiểu công cụ đánh giá hệ thống đảm bảo an toàn hệ thống thông tinThiết kế và chế tạo mô hình biến tần (inverter) cho máy điều hòa không khíSở hữu ruộng đất và kinh tế nông nghiệp châu ôn (lạng sơn) nửa đầu thế kỷ XIXChuong 2 nhận dạng rui roGiáo án Sinh học 11 bài 14: Thực hành phát hiện hô hấp ở thực vậtTrách nhiệm của người sử dụng lao động đối với lao động nữ theo pháp luật lao động Việt Nam từ thực tiễn các khu công nghiệp tại thành phố Hồ Chí Minh (Luận văn thạc sĩ)BÀI HOÀN CHỈNH TỔNG QUAN VỀ MẠNG XÃ HỘIĐổi mới quản lý tài chính trong hoạt động khoa học xã hội trường hợp viện hàn lâm khoa học xã hội việt namMÔN TRUYỀN THÔNG MARKETING TÍCH HỢP