Diploma in Mechanical Engineering (Production & Automobile) doc

... 2008) Delhi Road, Moradabad (U.P) Study & Evaluation Scheme of Diploma in Engineering (Mechanical) SUMMARY Programme : Diploma in Engineering (Mechanical) (a) Production (b) Automobile ... Mechanism:- Introduction, Kinetic link. Types of link, Difference between machine and structure, kinetic pairs, types of constrained motions, kinetic chains, types of joints in a chain, number ... Work: Ex-1 Planning and sawing practice. Ex-2 Making of Lap Joint. Ex-3 Making of Mortise and tendon Joint Ex-4 Making of Briddle Joint. Ex-5 Making of Dovetail Joint. Ex-6 Making of any one...

Higher National Diploma in Mechanical Engineering 2012 ppt

... Electronic Engineering and Instrumentation and Control. Derek worked in the telecommunication industry prior to becoming a lecturer in engineering. He gained a HND in Electrical & Electronic Engineering ... understanding of scientific principles underpinning mechanical systems. K3 Apply, question and relate mechanical engineering principles to produce solutions to a range of mechanical engineering ... Learning Engineering (TUOLE) 3 Programme Structure 3 Typical programme structure for an HND in Mechanical Engineering 4 Typical programme structure for an HND in Mechanical Engineering as...

Tài liệu PROBLEMS AND SOLUTIONS IN MECHANICAL ENGINEERING doc

... begins a new cycle. Applying thefirst law: in out in out final initial()()( )fQQ WW mh h−+−= −&&&&& in out out0, 0 0QQW===&&& in 1 4().fWmhh=−&&However, ... Work ratio is defined as the ratio of net plant output to the gross (turbine) output.Work ratio =out in 1out 1cWW WWWW−=&& & &&&Q. 21: Explain Rankine cycle with ... this process:(Q – Q ) + (W – W ) in out in out ..ººº=fm& (hfinal hmitial) in in out00 0.QW W== =&&&out 3 4()fQmhh=−&&(c) 3 - 4:The low-pressure...

Tài liệu Handbook of Mechanical Engineering Calculations P7 docx

... PUMPING SYSTEMSPUMPS AND PUMPING SYSTEMS7.61FIGURE 39 Constant-head curves for turbine only. (Chemical Engineering. )FIGURE 38 Constant-head curves for turbine duty. (Chemical Engineering. ) In ... PUMPING SYSTEMS7.60PLANT AND FACILITIES ENGINEERING FIGURE 36 Constant-speed curves for turbine duty. (Chemi-cal Engineering. )FIGURE 37 Constant-speed curves for turbine duty. (Chemi-cal Engineering. )Downloaded ... the website.PUMPS AND PUMPING SYSTEMSP•A•R•T2PLANT ANDFACILITIES ENGINEERING Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com)Copyright ©...

Tài liệu Handbook of Mechanical Engineering Calculations P8 doc

... resistance. Data shown in Table 38 are alsopresented in graphical form in some engineering data.2. Select a suitable piping materialRefer to piping engineering data to determine the corrosion resistance ... Consultant, DuPont Engineering (Table 44), as reported in Chemical Engineering Magazine. The economic study in Step 3 is the work ofMax Kurtz, P.E.FRICTION LOSS IN PIPES HANDLING SOLIDS IN SUSPENSIONWhat ... Engineering, Inc., as presented in Chem-ical Engineering magazine.ESTIMATING COST OF STEAM LEAKS FROMPIPING AND PRESSURE VESSELSSteam at 135 lb/ in 2(930 kPa) is leaking from a 0.05 in 2(0.32...

Tài liệu Handbook of Mechanical Engineering Calculations P11 doc

... liquidheating, gas and air heating, oven warming, deicing, humidifying, plastics heating,pipe heating, etc.Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com)Copyright ... FACILITIES ENGINEERING FIGURE 7 Heat losses from meltingpots. (General Electric Co.)TABLE 4Two Methods for Determining Wattage for Heating Buildings Electrically*Downloaded from Digital Engineering ... FACILITIES ENGINEERING FIGURE 6 Barometric condenser condensing-waterﬂow rate.gal/min at 35ЊF (0.11 m3/min per 3785 L/ min at 1.7ЊC). Using a value of 3 ft3/min (0.08 m3/min) for this...

Tài liệu Fiber in Broadcast and Production Facilities docx

... that when working with fiber, relying on factory-terminated cables offers several advantages over field termination, including performance and savings in labor, material costs and installation ... such as following a 1.5-inch bend radius policy, guarding against excessive cable pile-up, troughing horizontal runs, implementing vertical cable protection and providing for expanding slack ... higher performance and the elimination of wasted material and time offered by using factory-terminated fiber optic cable make a little re-orientation in engineering mindset and practice more than...

Tài liệu Mechanical Engineering Handbook P2 docx

... particles).3.The motion is in a nonaccelerating reference frame.FIGURE 1.3.6Motion of a particle in cylindrical coordinates.FIGURE 1.3.7Relative motion using translating coordinates.rrrvvvaaaBABABABABABA=+=+=+Fa=mMechanics ... particle that moves in circular motion the equations simplify to(1.3.11)Motion of a Particle in Cylindrical CoordinatesCylindrical coordinates provide a means of describing three-dimensional ... three-dimensional problems. In general, curvilinearmotion occurs and is analyzed using a convenient coordinate system.Vector Notation in Rectangular (Cartesian) CoordinatesFigure 1.3.3 illustrates...

Tài liệu Mechanical Engineering Handbook P1 doc

... learnsomething new, but what is needed at the moment is not at their ﬁngertips. This chapter may help thereader in such a situation. Within the constraints of a single book on mechanical engineering, ... following procedure is recommended.1.Determine the support reactions if the section used in the analysis includes the joints supported.FIGURE 1.2.23Method of joints in analyzing a truss.Joint ... ® Roadway Simulator, R&D100 Award-winning system in 1993. See alsoColor Plate 1. *Sandor, B.I.; Roloff, R; et. al. “Mechanics of Solids” Mechanical Engineering HandbookEd. Frank KreithBoca...

Tài liệu Handbook of Mechanical Engineering Calculations P13 doc

... to maintain the contents of the tank in a completely mixed state. Al-though there are numerous ways to accomplish continuous mixing, mechanical mixing will be used here. In mechanical mixing, ... trough. During the backwash cycle, wastewater is ﬁltered continuouslythrough the cells not being backwashed.Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com)Copyright ... website.Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS13.30ENVIRONMENTAL CONTROLbasin in series with the ﬁrst. The power input to the second basin is calculatedusing a lower G value (such...

Xem thêm