... HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\TerminalServer\WinStations\RDP-Tcp\PortNumber 2. Now, to access the server usingthe new setting, type the new port number after the IP address of the computer to which you want to connect. If the new port is 8098, and the IP address ... will open. Go tothe DNS tab and clear the Register this connection's addresses in DNS checkbox. In case you want to perform the same operation usingthe registry, open the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces ... specified on the General tab of the TCP/IP properties window. To disable this feature, click the Advanced button on the General tab of the Internet Protocol (TCP/IP) Properties window. The Advanced...
... run to add the new row tothe Products table. The database then generates a new ProductID for the row, which is then returned by the AddProduct4() stored procedure. You can then read the new ... database. The AddProduct4() stored procedure is run to add the new row tothe Products table, and the RowState of myNewDataRow changes to Unchanged. Modifying a DataRow in a DataTable The following ... ProductID is automatically generated by the database when the new row is pushed tothe database by the Update() method in step 4. When the Update() method is called, the AddProduct4() stored procedure...
... multiple administrators want to connect. If two administrators are connected yet not usingthe session, the third administrator cannot connect. Customizing a Network UsingtheRegistry It's ... considers them to be set to default values. Figure 8. 32: The Sessions tab of the RDP-Tcp Properties window Remote Desktop Port Settings In contrast tothe steps described above, the tweak ... risks. To modifythe default settings for Remote Desktop, proceed as follows: 1. Open the Control Panel, start Administrative Tools, then select the Terminal Services Configuration option. The...
... to call the stored procedures. • Add, modify, and remove a DataRow to from a DataTable. The C# methods shown in this section follow the same steps as shown in the earlier section, "Modifying ... run to push your changes tothe database. Let's take a look at how to set the InsertCommand, UpdateCommand, and DeleteCommand properties of your DataAdapter. Using Stored Procedures to ... Procedures to Add, Modify, and Remove Rows from the Database You can get a DataAdapter object to call stored procedures to add, modify, and remove rows from the database. These procedures are...
... display the new form, as shown in Figure 6 .26 . Notice that the top part of the form shows the details for the row from the Customers table where the CustomerID is ALFKI; the bottom part of the ... o Add The Add button allows you to add a new row. o Delete The Delete button allows you to delete the current row. o Cancel The Cancel button allows you to cancel a change made tothe current ... displays the rows from the Orders table for that customer. When you move to the next row in the Customers table, the rows from the Orders table for that customer are automatically displayed in the...
... will to decide whether or not you (or the user whose computer you're going to configure) really need this customization and, if so, just how much you (or the other user) need it. The customizations ... change the default settings of the operating system. Note that these default settings are satisfactory for most users. Before going any further, export theregistry keys that you're going to ... any further, read Chapter 2 carefully and make sure that you haven't skipped anything. Tip Before you edit theregistryto make any of the changes described in this chapter, read the appropriate...
... Open to Closed The InfoMessage Event The InfoMessage event fires when the database returns a warning or information message produced by the database. You use the InfoMessage event to monitor these ... "Introduction to Transact-SQL Programming." The following InfoMessageHandler() method is used to handle the InfoMessage event. Notice the use of the Errors collection to display the message: ... see how to use these events next. The StateChange Event The StateChange event fires when the state of your connection is changed, and you can use this event to monitor changes in the state...
... -2 63 (-9 ,22 3,3 72, 036,854,775,808) and 2 63 - 1 (9 ,22 3,3 72, 036,854,775,807). SqlMoney A currency value between - 922 ,337 ,20 3,685,477.5808 and 922 ,337 ,20 3,685,477.5807. This is accurate to 1/10,000th ... -2 15 (- 32, 768) and 2 15 - 1 ( 32, 767). SqlInt 32 A 32- bit signed integer between -2 31 ( -2, 147,483,648) and 2 31 - 1 (2, 147,483,647). SqlInt64 A 64-bit signed integer between -2 63 (-9 ,22 3,3 72, 036,854,775,808) ... that reads the ProductID, ProductName, UnitPrice, UnitsInStock, and Discontinued columns from the Products table usingthe GetSql* methods. To figure out which GetSql* method to use to retrieve...
... desktop windows, sending them flying tothe Dock. 1 .2. 4. Close Button As the tip of your cursor crosses the three buttons at the upper-left corner of a window, tiny symbols appear inside them: ... is an efficient way to backtrack to return tothe enclosing window. Get in the habit of right-clicking (or Control-clicking, or -clicking) the name of the window to access the menu shown in Figure ... cursor. The most important window gadget is the Close button, the red, droplet-like button in the upper-left corner (Figure 1-6). Clicking it closes the window, which collapses back into the icon...
... Hiding code in VS .NET usingthe #region directive To view hidden code, all you have to do is to click the plus icon tothe left of the code. Figure 6.6 shows the code within the #region and #endregion ... myLabel and myButton tothe form and sets the properties for those objects. These properties include the Location (the position in the form), Name, Size, TabIndex (the order in which the control ... and myButton, which are the label and button controls you added to your form earlier. Because the myLabel and myButton objects are private, this means that they are accessible only in the Form1...
... Mở rộng thị phần tín dụng theo hướng đầu tư khép kín gồm: sản xuất, chế biến, tiêu thụ, xuất khẩu (nội tệ, ngoại tệ) gắn nghiệp vụ tín dụng với thanh to n kể cả thanh to n quốc tế, vốn nội tệ, ... - Lập hồ sơ pháp lý theo quy định, quản lý hạn mức, theo dõi kiểm tra quá trình thực hiện dự án bảo lãnh vay vốn nước ngoài. Thực hiện chế độ báo cáo định kỳ và đột xuất theo quy định ... năng hàng nhằm mục tiêu phát triển kinh doanh an to n, hiệu quả của NHNo & PTNT VN. Nhiệm vụ: - Quản lý điều hành hoạt động tín dụng trong to n hệ thống NHNo & PTNT VN. - Dự thảo các...