... learning algorithm within the system
software. Establishing the touch point is the system's method for ensuring that the clutch
actuation system is properly calibrated. This is necessary ... learning
completes
successfully
Refer to Transmission
Control Module (TCM)
Adaptive Learning in
this section.
U002
8
Vehicle
Communication
Bus A
non-MIL sister
code to U0073
Holds current ... transmission. The
motors work independently of each other.
The clutch actuators are independent systems within the clutch housing which apply an axial
force operating against the clutch diaphragm springs...
... grinding
Width of linings
Thickness of linings (including mounting)
Minimum thickness of linings (including mounting)
Diameter of discs
Thickness of discs
Minimum thickness of discs (1)
Thickness of linings ... mm)
Diameter of slave cylinders
Diameter of discs
Thickness of discs
Minimum thickness of discs (1)
Thickness of linings (including mounting)
Minimum thickness of linings (including mounting)
Maximum ... Once converted by the
equipment, this variation is displayed in SEEM
units (US).
Calibration of the equipment
The equipment is calibrated at the factory, howe-
ver, this calibration must be checked...
... of two bolts around the gearbox.
92903S
C
engines
21-13
MANUAL GEARBOXES
Special features
GEAR CHANGE PATTERN
The gearboxes of the following types:
JB0
JB4
JB2
JB1
JB3 5 forward gears
JB5 1 ... the gearbox with oil.
21-28
MANUAL GEARBOXES
5th speed linkage in situ
21
On the secondary shaft:
Remove shouldered washer (64).
PRG21.1
Remove the fixed gear using tool B.Vi. 28-01-02-
03 fitted ... 1007.
88575R
REFITTING
On the secondary shaft:
Put three drops of
Loctite FRENBLOC
on the fixed
gear splines.
Fit the fixed gear using tool B. Vi. 1175 and shoul-
dered washer (64).
93462R
Remove tool B....
... them so
that they can be reconnected in their original positions. This is essential.
30
"X" TYPE BRAKING SYSTEM
with fixed compensator which
is integral with the wheel cylinder
91563-3S
"X" ... have
METRIC THREADS.
Consequently, it is important only to use the parts
shown in the Parts catalogue for this vehicle.
Parts identification :
- THE SHAPE of the ends of the steel or copper
PIPES (A),
-
THE ... is
driven over bumpy roads.
PARALLELISM
The steering must be in the straight ahead
position when this adjustment is carried out if a
detrimental effect on the road holding is to be
avoided.
It...
... 1989 or 1990 ?
Check for + 12 Volts on track 5 of the AC relay
Is this correct?
no
Check + 12 Volts on track 1 of relay 690.
Is this correct?
no
Check + 12 volts on track A1 of connector R99.
Is ... component
unit
connection
Is this correct?
Connection to component unit R99 disconnected,
ignition off, passenger compartment fan
operating and AC on MAX.
Check the wiring continuity between tracks A1
and C4.
Is this ... MAX).
Is this correct?
yes
Repair the wiring between
the control panel and
connector R99.
B2 A1
B4 C4
no
Change the control
panel.
Check the earth on track 6 of
the electronic thermostat.
Is this...
... notches) (two operators are required
to do this).
Start at the centre of the upper section of the
hood.
Rub the rear screen strip of material using the
smoothing tool in order to prevent creases ... Number: 77 01 041 838
1 - Clip and safety connection
2 - Slider
3 - Adhesive sealing strip
4 - Smoothing tool
Before carrying out any work, park the vehicle in
an area where there is an ambient temperature
of ... the hood without locking it.
99569
73-22
Description of operation :
REMOVAL
99563
Using the smoothing tool, lift the formed section
bead (A). Over a length of approximately 100 mm
at the lower...
... this line).
2 Body centreline: A - D - C (position of body jig bench bracket at Y, in relation to this line).
3 Base line: L - D - B (position of body jig bench bracket at Z, in relation to this ...
41
A
92567S
This operation is to be carried out on a body jig
bench. Refer to sub-section for instructions
on fitting the components.
PRS4112
BUTT WELDING JOINT ON THE SIDE MEMBER
1
Thickness of ... HEADLIGHT
CARRIER PANEL
3
Thickness of panels (mm)
Cross member: 1.25
Headlight carrier panel: 0.8
Unpicking
8 spot welds
One 15mm MAG weld fillet
Welding
BUTT WELDING JOINT ON THE LOCK SUPPORT
4
Thickness of...
... 1996
Edition Anglaise
Sealing and Soundproofing
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods ... constructed".
All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior ... inner rubbing strip
C
66-1
WINDOW SEALS
Rear door frame seal
66
E
Remove the trim and the small fixed window
Remove:
the seal, which is very fragile, using an extra-flat
chisel. Free the rear section...
... Pump
Fuel Flow
Cam
Piston
HỆ THỐNG NHIÊN LiỆU – SƠ ĐỒ MẠCH GIỚI THI U HỆ
THỐNG NHIÊN LIỆU GDI
13
Introduction of YF
Copyright 2009 All rights reserved. No part of this material may be reproduced, ... mức tiêu hao nhiên liệu 2%), Giảm sự độc
hại của khí thải (50%)
PHUN NHIÊN LiỆU TRƯC TIẾP (GDI)
45
Introduction of YF
Copyright 2009 All rights reserved. No part of this material may be ... the written
permission of Hyundai Motor Company.
GIỚI THI U VỀ ESC
Những hệ thống phanh ESC áp dụng trên xe HYUNDAI
Nhà san xuât Model Type Xe áp dung Lưu ý
MANDO
MGH-20 ABS+TCS GK, XD F/L, HR,...