... contain provisionswhich, through reference in this text, constituteprovisions of this part of this British Standard. For dated references, subsequent amendments to, orrevisions of, any of these ... Utilization of plastic design principlesThe use of plastic limit analysis, with redistribution of moments following the attainment of full plasticmoment capacity is permissible for plastic cross- sections ... workmanship: coldformed sections and sheeting.BS 6399-1, Loading for buildings Ð Codeof practice for dead and imposed loads.BS 6399-2, Loading for buildings Ð Codeof practice for wind loads.BS...
... capacity of the composite slab (or of the profiled steel sheets at the construction stage) to resist distortion in its own plane is not within the scope of this Part of BS 5950. For the designof ... width of slab; and is the shear bond capacity per unit width.ba is the mean width of a trough of an open profile (see Figure 2);bb is the minimum width of a trough of a re-entrant profile ... 8110-2:1985.Figure 4 — Typical profiles BRITISH STANDARDBS 5950-4:1994Structural use of steelwork in building —Part 4: Codeofpracticefordesignof composite slabs with profiled steel sheetingUDC...
... =5384wL4EIserwherew is the intensity of loading at the serviceability limit state;L is the span between the centres of supports;Iser is the effective second moment of area of the profile for serviceability ... stateDpOverall depth of the profileDwSloping distance between the intersection points of a web and flanges (see figure 4)d Diameter of a fastenerdpDiameter of a perforationdwDiameter of a washerE ... edge;E is the modulus of elasticity;t is the net thickness of the steel material.If bef,1+ bef,2$ Dwthe whole web is effective.Dw is the sloping distance between the intersection points of...
... Part 4: Codeofpracticefordesignof composite slabs with profiled steel sheeting.BS 5950-5, Structural use of steelwork in building — Part 5: Codeofpracticefordesignof cold formed thin ... use of steelwork in building — Part 6: Codeofpracticefordesignof light gauge profiled steel sheeting.BS 5950-9, Structural use of steelwork in building — Part 9: Codeofpracticefor stressed ... other forms of cold formed sections is covered in BS 5950-5.NOTE 3 Designfor seismic resistance is not covered in BS 5950. NOTE 4 The publications referred to in this standard are listed on...
... 3.1: Codeofpracticefordesignof simple and continuous composite beams;— Section 3.21): Codeofpracticefordesignof composite columns and frames;— Part 4: Codeofpracticefordesignof ... Specification for materials and workmanship: cold formed sections;— Part 8: Codeofpracticefor fire resistant design; — Part 91): Codeofpracticefor stressed skin design. This Part of BS5950 ... practicefordesignof floors with profiled steel sheeting;— Part 5: Codeofpracticefordesign in cold formed sections;— Part 61): Codeofpracticefordesign in light gauge sheeting, decking...
... Codeofpracticefor design of simple and continuous composite beams;— Part 4: Codeofpracticefordesignof composite slabs with profiled steel sheeting;— Part 5: Codeofpracticefordesign ... sections;— Part 8: Codeofpracticefor fire resistant design; — Part 9: Codeofpracticefor stressed skin design. This Part of BS 5950 gives recommendations for the use of profiled steel sheeting ... designof cold formed sections;— Part 61): Codeofpracticefordesignof light gauge profiled sheeting;— Part 7: Specification for materials and workmanship: cold formed sections;— Part 8: Code...
... accepted if, for example, it is assessed that the risk is low or that the cost of treatment is not cost-effective for the organization. Such decisions should be recorded. For each of the risks identified ... where this is practicable, realistic, and helpful. Examples of risk assessment methodologies are discussed in ISO/IEC TR 13335-3 (Guidelines for the Management of IT Security: Techniques for the ... estimate the risk [ISO/IEC Guide 73:2002] 2.11 risk assessment overall process of risk analysis and risk evaluation [ISO/IEC Guide 73:2002] 2.12 risk evaluation process of comparing...
... characteristics; (e) types of luminaires, their ratings and operating characteristics; CodeofPracticefor Building Energy Audit EAC_2012 1 of 11 EMSD 1. Introduction 1.1 This CodeofPractice ... Audit Form, to reflect the energy usage intensity of the central building services installations. The Energy Audit Form is a specified form under the Ordinance. CodeofPractice for Building ... first day of operation of the building; ii) indication of the EUI per annum (MJ/m2/annum) (based on the total energy consumption data in item i)), respectively for - CodeofPracticefor Building...
... farms, as it is necessary to isolate young chickens from laying hens. For biosecurity reasons, it is best practice to maintain a distance of 1,000 metres. ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY ... establish a benchmark environmental performance for members of theirassociations; and· provide those adhering to the Code with ‘clean, green marketing credentials’.This CodeofPracticeis intended ... ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA33PART 4 OTHER CONSIDERATIONS ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA243.4 NoiseExcessive noise...
... accepted if, for example, it is assessed that the risk is low or that the cost of treatment is not cost-effective for the organization. Such decisions should be recorded. For each of the risks identified ... where this is practicable, realistic, and helpful. Examples of risk assessment methodologies are discussed in ISO/IEC TR 13335-3 (Guidelines for the Management of IT Security: Techniques for the ... information is a shorthand way of determining how this information is to be handled and protected. 7.2.2 Information labeling and handling Control An appropriate set of procedures for information...
... normal supplies of feed or water are interrupted in emergency situations. Recommended codeofpracticefor the care andRecommended codeofpracticefor the care andhandling of poultry from ... evaluation of personnel is the responsibility of the employer.5.3.2 It is advisable not to feed birds for 3-6 h before loading.5.3.3 Careless catching of birds is a common source of injury. ... to the humane disposal of unhatched embryos must be a high priority of thehatchery. All unhatched embryos must be dead before disposal. The processing of unhatched embryos for disposal should...