... 1ME- 4 30 Introduction to Computer Aided Design CARD HOLDER - Pro/ ENGINEERWildfire3.0 Dr. Herli Surjanhata Pick the Create a new object icon . 13 CREATE ... Orientation box. 39 Click New Set for round Set 2. Enter 0. 5 mm radius of round for Set 2 Pick the edge as shown. Click New Set for round Set 3. Enter 1 .0 mm radius ... 35 Click . Enter the shell thickness of 3.0 mm. Pick the all side faces (THREE surfaces) and bottom surface as shown. Click . Create another shell with 0. 8...
... reference. 1ME- 4 30 Introduction to Computer Aided Design ARM BRACKET - Pro/ ENGINEERWildfire 2 .0 Dr. Herli Surjanhata In a system window, create a new directory called ME- 4 30 (e.g. H:\PTC_Working_Dir\ME- 4 30 ). ... Click to save the part. 3 Type in ARM_BRACK for the name of the new part. Un-check Use default template. The default units of Pro/ E is inlbs_part_solid. ... Horizontal: 10 Vertical: 12.5 This placement references can be verified by clicking the Placement tab. Click . 6 Click . Type in 40 for...
... The revolved angle is 30 degrees. RIGHT datum plane 1ME- 4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Helical Extension Spring Pro/ ENGINEERWildfire 2 .0 Dr. Herli Surjanhata ... Double click PITCH1 .00 , and change the value 0. 5. Pick the Regenerate icon . Pick the trajectory. 20 4 Sketch a circle with diameter 0. 25 centered on ... Click the Check button. Type in 30 for the angle. Click the button. Create R 0. 5 Sweep. From Insert pull-down menu, select Sweep -> Protrusion Select Sketch Traj...
... GRAPH menu and OK from the dialog box. ME- 4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Conical Spring Pro/ ENGINEERWildfire 2 .0 Dr. Herli Surjanhata START CREATING A NEW ... revolved angle to be 1 80. and click the button to finish. CREATE A REVOLVED PROTRUSION AT THE TOP PART OF SPRING Repeat the same procedure as shown above for 1 80 revolved protrusion, here ... click the helical sweep protrusion in the model tree, then select Edit. Pick the trajectory inclined line. Right click, and select Edit. Pick PITCH1 .00 and change the value...
... Add Dimension button , and select appropriate dimensions as shown below – The HEIGHT distance 3.00 0; the overall WIDTH 4 .000 and bottom RADIUS 8 .000 of balancing body. The three dimensions ... the datum point (e.g. PNT_COG_282) Then pick the axis (e.g. A_4 axis). The Distance = 0 .35 0 236 is shown under Results. Click the Close button. 5ANALYSIS FEATURES Click ... move. Pro/ ENGINEER evaluates the model at intervals throughout the range of the variable and graphs one or more design parameters (e.g. the offset distance vs. the dimension). 1ME- 4 30 INTRODUCTION...
... First chamfer: 45 X 0.03 First chamfer: 45 X 0.03 First chamfer: 45 X 0.03 First chamfer: 45 X 0.03 5 Click to re-dimension as shown ... select Properties. The Dimension Properties dialog box open. Change the Number of decimal places to 4. Change the Nominal Value to 1. 202 0. Change the Upper tolerance to 0.000 6 ... the same technique to create a 45º x 0. 02 in. chamfer on the edges shown below. Second chamfer: 45º x 0. 02 Second chamfer: 45º x 0. 02 10 In the dashboard, click the Remove...
... and then pick to complete the sweep. 1ME- 4 30 Introduction to Computer Aided Design TRAY - Pro/ ENGINEERWildfire 2 .0 Dr. Herli Surjanhata Pick the Create a new ... -> Protrusion. 15 Pick the appropriate additional reference, and Close the Reference dialog box. Sketch the following section. Click . Then Click . 13 Sketch ... the Model Tree. Pro/ ENGINEER highlights all of the part geometry in the graphics window. From Edit pull down menu, select the Mirror Tool . 12Create a Clip Protrusion ...
... bài viết này hướngdẫn chi tiết các bước cài đặt vCenter 5 .0 Chuẩn bị môi trường để cài đặt :- Bạn có thể cài vCenter lên 1 Server vật lý hoặc 1 Server ảo, để cho thuận tiện bạn nên cài đặt vCenter ... Server 200 8 R2 để cài vCenter.- Download bộ cài đặt vCenter 5 .0 từ webiste : www.vmware.com, chú ý là bạn có thể dùng thử 60 ngày (trial) nếu chưa có License của vCenter.Các bước cài đặt:- ... dùng Trial 60 ngày), Nhấn Next- vCenter cần có Database Server để lưu các thông tin, bạn có thể dùng : SQL Server, SQL Express, Oracle DB, trong hướngdẫn này ta sử dụng SQL Server 200 8 Express...
... r =0. 5*m*z1/cos(goc) todeg=1 80/ pi theta=t* 10* m*tan(goc)*todeg/r Z=-t* 10* m TIN HỌC ỨNG DỤNG AIC – 19 HÒA BÌNH - LÀNG ĐẠI HỌC THỦ ĐỨC - ĐT 08 .96 501 4 , 09 092 537 58 - 10 - Bước 3 : Tạo ... trụ răng thẳng. HƯỚNG DẪN THIẾT KẾ BÁNH RĂNG CÔN RĂNG THẲNG TIN HỌC ỨNG DỤNG AIC – 19 HÒA BÌNH - LÀNG ĐẠI HỌC THỦ ĐỨC - ĐT 08 .96 501 4 , 09 092 537 58 - 1 - HƯỚNG DẪN THIẾT KẾ BÁNH RĂNG ... được H. 10 . H.9 H. 10 Như vậy ta đã hoành thành xong phần phôi của bánh răng TIN HỌC ỨNG DỤNG AIC – 19 HÒA BÌNH - LÀNG ĐẠI HỌC THỦ ĐỨC - ĐT 08 .96 501 4 , 09 092 537 58 - 3 - 3. Tạo...