... limb) and premotor cortex (genu) fibresallows for lesions with and without spasticity (Frieset al., 1993).Although both cortical areas 4 and 6 must beaffected to produce spasticity and both ... loss of digital dexterity (Phillips &Porter, 1977) and, in humans, mild hand and footweakness, mild tendon hyperreflexia, normal tone and an extensor plantar response (Bucy et al., 1964;van ... is considered appro-priate and functional and a manifestation of normalreciprocalinnervation. Normal co-contraction is ini-tiated and modulated as the movement demands.Co-contraction is dysfunctional...
... Knowledge Management) o Effective KMS dựa trên việc học kiến thức mới và thay đổi thủ tục và hướng tiến cận như một kết quả (Is based on learning new knowledge and changing procedures and approaches ... conclusions and works backward to supporting facts)o Forward chaining Bắt đầu với những sự kiện và làm việc tiến tới kết luậnd. Yếu tố giải thích (The Explanation Facility)Chương 11: Knowledge Management ... tiến tới kết luậnd. Yếu tố giải thích (The Explanation Facility)Chương 11: Knowledge Managementand Specialized Information Systems1. Nguyên lý và mục tiêu học tập Quản lý tri thức là cho phép...
... TRANSACTION MANAGEMENT, AND AOP79In principle, the transactionality of the methods could be implemented by explicitly writing all of the methods with appropriate try and catch blocks, and accessing ... syntax and by creating custom Advice and Pointcut imple-mentation classes.Minter_685-4C05.fm Page 93 Monday, November 5, 2007 6:46 AM98CHAPTER 5 ■ THE SERVICE LAYER, TRANSACTION MANAGEMENT, AND ... transaction-manager="txManager"/>This uses XML namespaces and the Spring 2 support for XML schemas as a shorthand for the configuration of beans that generate and substitute a proxy class for your service...
... xxxWhat’s New in Backup and Recovery? xxxiiiOracle Database Release 10g New Features in Backup andRecovery xxxivPart I Recovery Manager Advanced Architecture and Concepts1 Recovery Manager ArchitectureAbout ... 14-11Instance Recovery Performance Tuning: FAST_START_MTTR_TARGET 14-12Understanding Instance Recovery 14-12Checkpointing and Cache Recovery 14-13Configuring the Duration of Cache Recovery: FAST_START_MTTR_TARGET ... interactively, start RMAN and then type commands intothe command-line interface. For example, you can start RMAN from the UNIXcommand shell and then execute interactive commands as follows:% rman...
... three types of recovery: Instance Recovery, Media Recovery, and Flash Recovery, as described in the following sections.Instance Recovery Only one setting refers to instance recovery, FAST_START_MTTR_TARGET, ... restore database command, limiting the restore to SCN 764904. 6. Issue the recover command, again limiting the recovery of the database to SCN 764904, and wait for the recovery to complete. ... recovery, and then you need to perform cancel-based recovery of the database from the SQL*Plus client. Chapter 1 describes the process of performing manual cancel-based database recovery. Recovery...
... sites.Backup andRecovery with RMAN1-12 Backup andRecovery BasicsBackup andRecovery with RMANAs noted earlier, using RMAN gives you access to several data backup and recovery techniques and features ... appropriate recovery from a media failure depends on the files affected and thetypes of backup available.Oracle Backup andRecovery Solutions: RMAN and User-Managed BackupFor performing backup andrecovery ... example:■Using Recovery Manager simplifies most backup andrecovery operationscompared to user-managed backup and recovery. It automates management ofmost backup files, including the deletion of backups and...
... validate command, which allows you to examine a given backup set and verify that it can be restored. This command is similar to the backup validate command, with a few extra bells and whistles. ... restore andrecovery operations, but protects the backup record from being removed during the execution of the delete expiredcommand. Here are some examples of the use of the change command:change ... type disk unavailable;You can also use the change command to delete backup sets (physically on the backup media and from the control file andrecovery catalog). The delete parameter is used for...
... available to you for recovery purposes.We also talked about the change and delete commands and how they can be used to modify the status of RMAN records in the control file or recovery catalog. ... helps support recovery through resetlogs and also helps support easier recovery to a previous incarnation.An important point to note is that output generated with a recovery catalog and output ... the RMAN report command. Each of these commands provides facilities for in-depth analysis of the database that you are using RMAN to back up and its backups. These commands are the primary...
... the basics of Data Guard standby databases and are ready to create one using RMAN.RMAN and the Standby DatabasePrimarily, the relationship between RMAN and the standby database is a simple ... standby completes, your standby database is mounted but not open, and you will need to decide how to proceed with media recovery. If you would like RMAN to perform the initial media recoveryand ... used to create the standby database using the duplicate…for standby command. We discussed the means by which you use the duplicate command to create the standby database and included an RMAN...
... use for disaster recovery. Although disaster recovery is inherent in the hardware sync and split model as well, having a FIGURE 22-4 Using sync and split with a standby database and Flashback ... the commandThe syntax diagram for the commandThe relevant chapter in the book in which you can find more details on the commandExamples of the use of the command@ CommandThe @ command executes ... UPGRADE CATALOG VALIDATERMAN Specifier and Operands ListsThe following table provides the names of the various RMAN specifiers and operands. allocOperandList archivelogRecordSpecifier completedTimeSpecconnectStringSpec...
... isactually needed to physically make the connection, and what the technician actuallyhas to work with.Cable Managementand Slack StorageCable Management and Slack StorageWHITE PAPER ... importance of fiber cable managementand how it candramatically affect the operational costs of a network. ADC has a wealth of experiencein the areas of cable managementand slack storage systems ... protection, and easy access to individual fibers. It will also mitigate many potentialproblems that non-managed systems could face over time.Keys to Unlocking Fiber Management Good fiber cable management...
... rec cat;create script CommandThe create script command allows you to create a stored command script within RMAN. You must have a recovery catalog to use this command.Syntax DiagramCREATEGLOBALSCRIPT’script_name’COMMENT’comment’{backupCommandsmaintenanceCommandsmiscellaneousCommandsrestoreCommands}FROM ... DiagramCREATEGLOBALSCRIPT’script_name’COMMENT’comment’{backupCommandsmaintenanceCommandsmiscellaneousCommandsrestoreCommands}FROM FILE’filename’;Chapter ReferenceThe create script command is referenced in Chapter 10.Examplecreate ... archivelog time between 'sysdate' and 'sysdate-30';delete CommandThe delete command allows you to mark backups and copies in the recovery catalog or control file with a status...
... Lab 13.9.3: Windows Registry Backup andRecovery Estimated time: 20 Minutes Objective In this lab, the student will learn how to back up and perform a recovery of the registry. These files ... displays. Supply a label for the backup job and for the backup media. Windows will supply a backup label and media label by using the current date and time by default. In the Backup Label text ... state and registry files. Step 1 Log on to the Server with the Administrator account When the systems boots up, Click Start, and then click Run. In the “Run Dialog box, type “ntbackup” and...