... not in the ON position,
the ignition relay in the IPDM E/R is ON.
XX
Ignition relay (inte-
grated in IPDM E/R)
IGN RELAY OFF —
When the ignition switch is not in the ON position,
the ignition ... M61.
LH Turn Signal Lamp
When the turn signal switch is moved to the left turn position, the BCM receives an input signal requesting left
turn signals to flash. The BCM then supplies power
• through ... “SELECT DIAG MODE” screen.
When lighting switch is 2ND
position
: HEAD LAMP SW 1 ON
: HEAD LAMP SW 2 ON
Headlamp low beam should operate.
Headlamp low beam should operate.
When lighting switch is...
... modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front ... distribution module engine room) controls the headlamp high and
headlamp low relay coils. These relays, when energized, direct power to the respective headlamps, which
then illuminate.
If voltage is applied ... position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
signal requesting the headlamps (and...
... there is a
problem either with the vehicle or with the tester.
HINT:
• If communication is normal when the tester is
connected to another vehicle, inspect the DLC3
of the original vehicle.
• ... and the Diagnostic Trouble
Codes (DTCs) can be read from the Data Link
Connector 3 (DLC3) of the vehicle. When the
system seems to be malfunctioning, use the
intelligent tester to check for ... repairs.
2. CHECK DLC3
(a) The ECU uses ISO 15765-4 for communication.
The terminal arrangement of the DLC3 complies
with SAE J1962 and matches the ISO 15765-4
format.
NOTICE:
*Before measuring the...
... 1, Mạch đèn pha cốt:
a, Nguyên lí hoạt động:
Khi bật khoá sang vị trí ON,
đi ệ nt ừ ắ cqui →công t ắ c khoá →
công tắc chính của hệ thống đèn
→
công tắc ... phucô trong chụp nhôm. Dòng phucô tác dụng với từ
trường của nam châm làm chụp nhôm quay, kéo theo kim chỉ vận tốc tương ứng
trên vạch chia của đồng hồ. Mômen quay của chụp nhôm được cân bằng ... đổi.
Hình.1. Đồng hồ tốc độ xe loại cáp mềm
2, Mạch xi nhanh:
a, Nguyên lí hoạt động:
Khi bật khoá sang vị trí ON,
điệ nt ừ ắ cqui →khoá→
Cực B của rơ le xi nhanh .
Khi gạt công tắc qua trái hoặc...
... 2.
2.SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed ... OPERATION
When the interior room lamp switch is in the DOOR position and when all conditions below are met, the BCM
begins timer control (maximum 30 seconds) for interior room lamp ON/OFF.
• When the ... the interior room lamp timer control function of the BCM.
• Trunk room lamp (if equipped) is controlled by the trunk room lamp control function of the BCM.
The timer control functions of the...
... check that the LED in the
"HomeLink" logo illuminates as illustrated. If one or
more of the switches do not cause the LED to
illuminate, confirm that the fuse and the wiring to the ... bring the original
handheld transmitter within 2 to 9 cm (1 to 3 in.)
of the garage door opener system. Press and
hold the switch on the handheld transmitter. If
the flashing speed of the garage ... the way of the garage door or other device.
• Before beginning programming of the garage
door opener system, turn off the engine and
remove the key from the ignition key cylinder.
• The garage...
... điểm sáng đặt ngay tiêu c F của pha phản
chiếu parabôn. Chùm tia sáng phản chiếu thay đổi tuỳ theo vị trí vị trí của dây tóc
bóng đèn đối với tiêu cự của pha đèn. ánh sáng từ bóng đèn tập trung ... của khí halogen
làm tăng tuổi thọ của dây tóc và loại trừ vách thuỷ tinh bóng đèn bị phủ đen theo thời
gian và đảm bảo pha đèn luôn trong sáng.
10.1.2 Sơ đồ mạch điện hệ thống đèn pha cốt
Sửa...
... xa so
với dòng điện nhỏ đó để có thể vượt qua khe hở lớn của má vít. Khi mà
sự vượt dòng qua khe khi má vít mở bị hạn chế, chúng ta sẽ không nghe
thấy tiếng rè nhiễu trên radio.
Má vít cần ... đều có một điện trở để chống nhiễu cho sóng
radio. Khe hở bugi quá rộng, lượng điện thế không đủ lớn để vượt qua
tạo ra mất tia lửa điện. Khe hở quá hẹp, điện áp tập trung trên bugi sẽ
lớn dẫn ... tụ điện không có ở đấy, nó sẽ cố gắng vượt qua khe của má vít
khi má vít mở. Nếu điều đó sảy ra, má vít sẽ nhanh chóng bị cháy và bạn
có thể nghe thấy tiếng lách cách trên radio của xe. Để tránh...
... phân xưởng SCCK
Dây dẫn và cáp trong mạng điện được lựa chọn theo các điêu kiện sau đây:
- Lựa chọn theo điều kiện phát nóng
- Lựa chọn theo điều kiện tổn thất điện năng cho phép.
Đối với mạng đện ... ta chọn theo điều kiện tổn thất cho phép, sau đó nhất thiết
phải kiểm tra theo điều kiện phát nóng vì đây là điều kiện đảm bảo an toàn đối với
dây dẫn và cáp.
Dây dẫn hạ áp được chọn theo điều ... 1,4
Trong đó: S’
đm
: Là công suất định mức của máy biến áp sau khi đã hiệu
chỉnh theo nhiệt độ . S’
đm
được tính theo công thức:
S’
đm
= S
đm
.
−
−
−
−
100
35
1.
100
5
1
cdtb
θθ
Trong...