... situations. Recommended codeofpracticefor the care and Recommended codeofpracticefor the care and handling of poultry from hatchery to processing planthandling of poultry from hatchery ... Facilities forand handling of loose-housed poultry5.2.1 Proper building design and accessibility to transport vehicles greatly improves the humanehandling of loose-housed poultry. Owners and operators ... and watering space, an adequate and predictable supply of feed and water, and an adequate number of nest boxes and roosts. 142.5 Supervision and protection of chickens2.5.1 Chicken flocks...
... use of steelwork in building — Part 4: Codeofpracticefor design of composite slabs with profiled steel sheeting.BS 5950-5, Structural use of steelwork in building — Part 5: Codeofpractice ... carbon steel bars for the reinforcement of concrete.BS 4482, Specification for cold reduced steel wire for the reinforcement of concrete.BS 4483, Steel fabric for the reinforcement of concrete.BS ... 5: Codeofpracticefor design of cold formed thin gauge sections.BS 5950-6, Structural use of steelwork in building — Part 6: Codeofpracticefor design of light gauge profiled steel sheeting.BS...
... Information Labeling and secure handling of classified information is a key requirement for information sharing arrangements. Physical labels are a common form of labeling. However, some information assets, ... guidelines This codeofpractice may be regarded as a starting point for developing organization specific guidelines. Not all of the controls and guidance in this codeofpractice may be applicable. ... operations; e) management and business consultants, and auditors; f) developers and suppliers, e.g. of software productsand IT systems; g) cleaning, catering, and other outsourced support...
... forced fan ventilation. ‘Director’ means the Director of Electrical and Mechanical Services. CodeofPracticefor Building Energy Audit EAC _2012 9 of 11 EMSD cost benefit analyses, and ... reference no. CodeofPracticefor Building Energy Audit EAC _2012 6 of 11 EMSD 7.2 – Collection of Building Information Information on building operation characteristics and technical ... Energy Audit EAC _2012 1 of 11 EMSD 1. Introduction 1.1 This CodeofPractice titled CodeofPracticefor Building Energy Audit”, hereinafter referred as the “Energy Audit Code or “EAC“,...
... handling;· Manual handling; and · Vehicle and equipment safety. ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA33PART 4 OTHER CONSIDERATIONS ENVIRONMENTAL CODEOFPRACTICE ... Welfare of Animals: Land Transport of Poultry, available from the Internet site<www.publish.csiro.au> ;and the Department of Local Government and Regional Development’s Code ofPracticefor ... for transportation to the central grading floor in Palmyra for grading and retaildistribution. ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIAiv ENVIRONMENTAL CODE OF...
... information is a shorthand way of determining how this information is to be handled and protected. 7.2.2 Information labeling and handling Control An appropriate set of procedures for information ... techniques — Codeof practice for information security management 1 Scope This International Standard establishes guidelines and general principles for initiating, implementing, maintaining, and ... contracts and other factors as required. In serious cases of misconduct the process should allow for instant removal of duties, access rights and privileges, andfor immediate escorting out of the...
... materials and workmanship: coldformed sections and sheeting.BS 6399-1, Loading for buildings Ð Codeof practice for dead and imposed loads.BS 6399-2, Loading for buildings Ð Codeof practice for ... practicefor protective coating of iron and steel structures against corrosion1).BS 5502-22, Buildings and structures for agriculture Ð Codeofpracticefor design,construction and loading.BS ... properties of fasteners ÐBolts, screws and studs.CP3 Codeof basic data for the design of buildings:Chapter V: Part 2: Wind loads.1.4 Terms and definitions For the purposes of this part of BS...
... 3.4 and 3.5 of BS 8110-1:1985 or Tables 5.1 and 5.2 of BS 8110-2:1985.Figure 4 — Typical profiles BRITISH STANDARDBS 5950-4:1994Structural use of steelwork in building —Part 4: Codeofpractice ... loadDpOverall depth of profiled steel sheetsDsOverall depth of composite slabdsEffective depth of slab to centroid of profiled steel sheetsE Modulus of elasticity of profiled steel sheetsFaEnd ... factor of 1.25 is a partial safety factor for resistances gm, selected on the basis of the behaviour and mode of failure of the slab.The empirical parameters mr and kr in this formula...
... Rt,0.5 and Rmshould normally be taken as specified in the relevant product standard for the steel sheet or strip and used for the formed sections. For information, the resulting values of Ys and ... Properties of materials and section properties3.1 Range of thicknessesThe provisions of this Part of BS 5950 apply primarily to profiled steel sheet with a net thickness of steel basemetal of not ... stateDpOverall depth of the profileDwSloping distance between the intersection points of a web and flanges (see figure 4)d Diameter of a fastenerdpDiameter of a perforationdwDiameter of a washerE...
... 3.1: Codeofpracticefor design of simple and continuous composite beams;— Section 3.21): Codeofpracticefor design of composite columns and frames;— Part 4: Codeofpracticefor design of ... Specification for materials and workmanship: cold formed sections;— Part 8: Codeofpracticefor fire resistant design;— Part 91): Codeofpracticefor stressed skin design.This Part of BS5950 ... of floors with profiled steel sheeting;— Part 5: Codeofpracticefor design in cold formed sections;— Part 61): Codeofpracticefor design in light gauge sheeting, decking and cladding;—...
... 3.1 Codeofpracticefor design of simple and continuous composite beams;— Part 4: Codeofpracticefor design of composite slabs with profiled steel sheeting;— Part 5: Codeofpracticefor ... design of cold formed sections;— Part 61): Codeofpracticefor design of light gauge profiled sheeting;— Part 7: Specification for materials and workmanship: cold formed sections;— Part 8: Code ... sections;— Part 8: Codeofpracticefor fire resistant design;— Part 9: Codeofpracticefor stressed skin design.This Part of BS 5950 gives recommendations for the use of profiled steel sheeting...