0

car rim part

Tài liệu Car Rim – Part and Assembly Photo Rendering pdf

Tài liệu Car RimPart and Assembly Photo Rendering pdf

Kĩ thuật Viễn thông

... INTRODUCTION TO COMPUTER AIDED DESIGN Car RimPart and Assembly Photo Rendering Pro/ENGINEER Wildfire Dr. Herli Surjanhata Create a part named car_ rim with three default datum planes and ... shown below. ASSEMBLE THE RIM AND TIRE 21 13 CREATE A BLIND HOLE The hole is made co-axis with the rim, and DTM4 is taken as primary reference. 10Pattern ... resulting cut: Mirror the cut about TOP datum plane. CREATE AN INSIDE CUT ON THE TOP PART OF THE RIM The cut is made by revolving the rectangular section shown below. 2 The resulted...
  • 21
  • 247
  • 0
TU petrol engine in-car repair procedures (Part A) potx

TU petrol engine in-car repair procedures (Part A) potx

Kĩ thuật Viễn thông

... itremains in the car. If the engine has beenremoved from the car and is being dismantledas described in Part C, any preliminarydismantling procedures can be ignored. Referto Part B for the ... 45°2A•2 TU engine in -car repair procedures1 General informationHow to use this Chapter1 This Part of Chapter 2 describes thoserepair procedures that can reasonably becarried out on the TU ... the relevant Part of Chapter 4, carry out the following tasks:a) Refit all disturbed wiring, hoses andcontrol cable(s) to the inlet manifold andfuel system components.b) On carburettor models,...
  • 14
  • 587
  • 0
XU petrol engine in-car repair procedures (Part B) potx

XU petrol engine in-car repair procedures (Part B) potx

Kĩ thuật Viễn thông

... remains in the car. If the engine hasbeen removed from the car and is beingdismantled as described in Part C, anypreliminary dismantling procedures can beignored. Refer to Part A for information ... freetowards the front of the car (see Part A). Donot try to swivel the head on the cylinderblock/crankcase; it is located by dowels, aswell as by the tops of the liners. Take care notto damage the ... remove all tracesof gasket and carbon; also clean the pistoncrowns. On ‘wet’ liner engines, refer toparagraph 36 before turning the engine. Takeparticular care on these models, as the softaluminium...
  • 24
  • 1,330
  • 0
Part IV: Advanced Tips and Tricks

Part IV: Advanced Tips and Tricks

Thiết kế - Đồ họa - Flash

... on the type of layer you’reworking on:310 Part IV: Advanced Tips and Tricks 22_129869 ch15.qxp 11/29/07 12:03 PM Page 310In this part . . .This part contains two chapters. Chapter 16 covers ... in.That’s all there is to it! The on-demand companies take care of the sales, theprinting, and the mailing of your manga or comic. The best part of this deal isthat it costs you nothing to do this. ... (or whomay purchase a trade paperback of your series should you decide to print it).332 Part V: The Part of Tens 24_129869 ch16.qxp 11/29/07 12:04 PM Page 332To outline a selection you created,...
  • 39
  • 820
  • 0

Xem thêm

Tìm thêm: xác định các mục tiêu của chương trình xác định các nguyên tắc biên soạn khảo sát các chuẩn giảng dạy tiếng nhật từ góc độ lí thuyết và thực tiễn khảo sát chương trình đào tạo gắn với các giáo trình cụ thể xác định thời lượng học về mặt lí thuyết và thực tế tiến hành xây dựng chương trình đào tạo dành cho đối tượng không chuyên ngữ tại việt nam điều tra với đối tượng sinh viên học tiếng nhật không chuyên ngữ1 khảo sát thực tế giảng dạy tiếng nhật không chuyên ngữ tại việt nam khảo sát các chương trình đào tạo theo những bộ giáo trình tiêu biểu nội dung cụ thể cho từng kĩ năng ở từng cấp độ xác định mức độ đáp ứng về văn hoá và chuyên môn trong ct phát huy những thành tựu công nghệ mới nhất được áp dụng vào công tác dạy và học ngoại ngữ mở máy động cơ rôto dây quấn hệ số công suất cosp fi p2 đặc tuyến mômen quay m fi p2 đặc tuyến dòng điện stato i1 fi p2 sự cần thiết phải đầu tư xây dựng nhà máy thông tin liên lạc và các dịch vụ phần 3 giới thiệu nguyên liệu từ bảng 3 1 ta thấy ngoài hai thành phần chủ yếu và chiếm tỷ lệ cao nhất là tinh bột và cacbonhydrat trong hạt gạo tẻ còn chứa đường cellulose hemicellulose