... FastEthernet0
C 192.168.1.0/24 is directly connected, Serial1
S* 0.0.0.0/0 is directly connected, Serial1
RouterB#
Understanding The Routing
Table
Part 1: The Routing Table Structure
Part 2: The ... default routing behavior, whether classful or classless, is simple. The command to enable
classless routing behavior is:
RouterB(config)#ip classless
RouterB(config)#
The command to disable classless ... brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 172.16.4.1 YES NVRAM up up
Loopback1 172.20.0.1 YES manual up up
Loopback2 172.30.0.1 YES manual up up
Serial0 192.168.1.2 YES NVRAM up...
... tells the Copyright Office who they should
mail the registration certificate to. If this is the same as the person
(or organization) in Section 3, check the first box. If it’s the same as
the ... AGREEMENTS
The problem was that the consultants had signed an NDA say-
ing they wouldn’t reverse-engineer the interface, so the court
ruled that they couldn’t use the trade secrets they’d obtained ... check the Citizenship and United
States boxes. If the author is a citizen of some other country,
check the Citizenship and Other boxes on the first line of this
item, and then select the name...
... Relay.
–However, there are times when the benefits outweigh
the cost of the leased line.
The dedicated capacity removes latency or jitter
between the endpoints.
–Constant availability is essential ... modulates the binary data into an analog signal
at the source and demodulates the analog signal to binary
data at the destination.
The physical characteristics of the local loop to the PSTN ... Academy
Choosing a WAN Link Connection
What is the purpose of the WAN?
–Do you want to connect local branches, connect
remote branches, connect to business partners?
What is the geographic...
...
–Data is encapsulated by the sending router.
The frame is sent on a physical medium to the WAN.
–There are various ways to traverse the WAN,
The receiving router uses the same communications ... signal back into a sequence of bits.
The remote DCE then signals this sequence to the
remote DTE.
The connection between the two DCE devices is
the WAN service provider transmission network. ... Enter the interface configuration mode of the
serial interface.
–Step 2. Enter the encapsulation hdlc command to
specify the encapsulation protocol on the interface.
The output of the show...
... unicast so that the other node
gets the routing updates.
In the example, R1 uses the frame-relay map
command to map the VC to R2.
To verify the Frame Relay mapping, use the
show frame-relay ... connections.
The output shows the following
information:
•10.140.1.1 is the IP address of the
remote router, dynamically learned
via the Inverse ARP process.
•100 is the decimal value of the local ... in the memory of each switch
–As the frame moves across the network, Frame
Relay labels each VC with a DLCI.
The DLCI is stored in the address field of every
frame transmitted to tell the...
...
Please refer to the chart at the end of thelab to correctly identify the interface identifiers to be used
based on the equipment in the lab. The configuration output used in this lab is produced ... the previous steps, finish thelab by doing the following:
• Logoff by typing exit
• Turn the router off
• Remove and store the cables and adapter
2 - 8 CCNA 4: WAN Technologies v 3.0 - Lab ... the following according to the chart:
• The hostname
• The console
• The virtual terminal
• The enable passwords
If there is a problem completing this, refer to the Network Address Translation...
... Please refer to the chart at the end of
the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The
configuration output used in this lab is produced ... reload instructions at the end of this lab. Perform those steps on all
routers in this lab assignment before continuing.
Step 1 Configure the routers
On the routers, enter the global configuration ... configure the hostname as shown in the
chart. Then configure the console, virtual terminal and enable passwords. Next configure the
6 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab...
... cycle the switch (hardware restart) instead of issuing the
reload command. To power cycle the switch, remove the power cord from the back of the
switch or unplug it. Then plug it back in.
If the ...
refer to the Basic Switch Configuration lab.
Step 2 Configure the hosts attached to the switch
Configure the hosts to use the same IP subnet for the address, mask, and default gateway as on the ... network similar to the one in the diagram. The configuration output used in this lab is
produced from a 2950 series switch. Any other switch used may produce different output. The
following steps...
... Missing Manual by David Sawyer McFarland
eBay: The Missing Manual by Nancy Conner
Excel 2003: The Missing Manual by Matthew MacDonald
Excel 2007: The Missing Manual by Matthew MacDonald
Facebook: The ... options:
• Themanual way is to click the [edit] link for a section below the lead section, then
go to the URL at the top of the screen and change the number at the end of the
Figure 1-12. An article with ... Biersdorfer, and
Matthew MacDonald
The Internet: The Missing Manual by David Pogue and J.D. Biersdorfer
iMovie 6 & iDVD: The Missing Manual by David Pogue
iMovie ’08 & iDVD: The Missing Manual by...
... 2007: The Missing Manual by Matthew MacDonald
Excel 2010: The Missing Manual by Matthew MacDonald
Facebook: The Missing Manual, Second Edition by E.A. Vander Veer
FileMaker Pro 10: The Missing Manual ... Missing Manual by Matthew MacDonald
Buying a Home: The Missing Manual by Nancy Conner
CSS: The Missing Manual, Second Edition, by David Sawyer McFarland
Creating a Web Site: The Missing Manual, ... followed
by the version number and the
”.dmg”extension. Launch the
installer by double-clicking the
box icon. ThePDF file contains
information about the release
that you can read while the
...
... the command they want. Other people like to press the mouse button
continuously as they click the menu title and drag down the list to the desired
command; only then do they release the mouse ... above and slightly to the right of the
stage. Drag the word the straight up so that it is above the stage.
These are the starting positions for each of the words. They should be com
-
pletely ... appears, and the W/H Size properties determine the dimensions of
the text box. Keep in mind that the Size properties change the size of the text box,
but they don’t change the size of the letters....
...
I wanted to keep the user and group permissions the same, I needed
to make sure that they each had read (4) and write (2) permissions
(4 + 2 = 6). Because I want the “other” group to be the ... be set on the file. The
first field determines whether it is a directory. Desktop is a directory as
denoted by the d in the first field. The next three fields each represent
the owner, the group, ... Hands-on Guide to the Red Hat
®
Exams: RHCSA
™
and RHCE
®
Cert Guide and Lab Manual
e
Moves to the end of a word
b
Moves to the beginning of a word
$
Moves to the end of a line
H
Moves to the first line...