2 Mbps DSX Front Cross-Connect Solutions 600 mm Mbps DSX Product Family DSX Introduction 600 mm Products Digital signal cross-connect (DSX) products are used to connect one piece of digital telecommunications equipment to another This simplifies equipment connections and provides a convenient test access point as well as a convenient location for rearranging and restoring circuits Cross-connecting network elements of a DSX is a simple, efficient way of organizing a facility's digital telecommunications equipment There are three basic areas in a DSX The wire termination area for terminating the signal (wire) from a network element The cross-connect area, used to connect the two DSXs that have terminated the signals from two digital network elements And finally, the heart of the DSX, the jack Each DSX jack provides an OUT, IN and MONITOR signal access point The OUT and IN switching jacks provide direct access to the network element's input and output signals These jacks provide a means of temporarily breaking the connection between DSX panels that are cross-connected together and allow access to the signals for test and patching operations A MONITOR jack with high impedance bridge networking is connected to the OUT jack for nonintrusive access to the output signal of each network element At 2.048 Mbps rate, DSX-1 panels connect network equipment such as office repeater bays, channel banks, multiplexers, digital switches, loop carriers, loop switches, radio, fiber optic systems, and other Mbps equipment Traditional DSX Application Network Element A LED Tracer Wire DSX MON MON OUT Tx OUT IN 100571 Rx IN M X-OUT OUT IN X-IN PERMANENT EQUIPMENT CABLE Network Element B DSX X-OUT Typical DSX SemiPermanent Cross Connect Jumper OUT O I IN Tx OUT Rx IN X-IN PERMANENT EQUIPMENT CABLE Test Box 10/03 • Test Box OUT IN Monitoring and testing with traditional DSX requires finding and going to two locations for complete circuit testing It also requires access to both DSX sites and the time necessary to travel and setup test gear in two locations DSX Features and Benefits • • • • • OUT/IN jacks – Fast and easy access to circuits for testing, monitoring and patching Bantam die-cast jacks – Guarantees quality and reliability over time Flashing LEDs available in a variety of colors – Provides easy circuit identification Multiple designs and configurations – Design optimized for each application Coax and 120 Ohm connections provide the flexibility to connect 75 Ohm equipment to 120 Ohm equipment www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 122 Mbps DSX Front Cross-Connect Solutions 600 mm Mbps DSX Product Family The Products FlexDSX™ Panel PxPlus™ Panel Loaded 600 mm Skeleton Bay Empty 600 mm Skeleton Bay DSX 64-Termination Panel 10/03 • 100571 600 mm Products The 600 mm skeleton bay is the basis of ADC’s Mbps DSX product offering The fully-assembled bay meets the standard ETSI 600 mm wide x 2200 mm tall footprint The fuse panel and all the necessary cable management are factory-installed in the bay making installation and ordering fast and easy DSX panels are added in the field as needed The 600 mm skeleton bay is compatible with all ADC 64-termination DSX panels A total of 832 twisted pair or coaxial terminations fit in each bay www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 123 Mbps DSX Front Cross-Connect Solutions Product Selection Guide FlexDSX™ Panels FlexDSX panels offer four-port jack access with dual monitor for applications where the cross-connect may be located far away or is inaccessible such as in collocation applications The dual monitor port also allows for fast isolation of problems as both sides of the circuit can be accessed easily from one termination The jacks are individually removable and the backplane terminations are removable in groups of four 600 mm Products PxPlus™ Panels Ideal for applications requiring three-port jack access and true cost-deferment as equipment cables can be preterminated and jacks can be added as needed If the chassis has more than 60% of its terminations turned up within one year, the fixed, non-modular DSX 64 panels may be a better choice for a high growth environment DSX 64-Termination Panels Ideal for applications where individual circuit modularity is not required This is a fixed, non-modular 64 termination panel with three-port jack access Feature/Need FlexDSX PxPlus DSX 64 64 terminations/panel (Balun & twisted pair) X X X Mounts in IBF-RSC021 skeleton bay X X X (832) Mbps terminations per bay X X X Tracer LED X X X X X X Oversized labels X X X In-service patching and circuit rearrangement X X X Balun options (BNC & 1.6/5.6) X X X Patching and monitoring capabilities X X X Removable jacks X X Dual monitor (4 port jacks) X Variety of backplanes and connector options to fit into chassis X 10/03 • 100571 Ability to prewire backplane www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 124 Mbps DSX Front Cross-Connect Solutions ADC 600 mm Skeleton Bay for FlexDSX™, PxPlus™ and DSX64 Panels 600 mm Products The 600 mm skeleton bay is designed for FlexDSX, PxPlus and DSX 64-termination panels The fullyassembled bay meets the standard ETSI 600 mm wide x 2.2 meter tall footprint for easy office planning Rack mounting will also accommodate standard 48.26 cm (19 inch) panels Fuse panels and all the necessary cable management are factory-installed in the bay, making ordering and installation fast and easy DSX panels are added in the field as needed OUT (Tx) and IN (Rx) cable ways for equipment terminations support the use of either 120 Ohm twisted pair or 75 Ohm coaxial cable The skeleton bay can be mounted on either concrete or raised floor Extra rack space reserved for miscellaneous applications (such as cross aisle panels or monitor panels) or for additional DSX panels (up to [832] Mbps terminations) High-density supports up to (12) 5.25-inch (13.34 cm) panels or (768) Mbps terminations (120 Ohm or 75 Ohm) per bay Single part number simplifies ordering and installation Panels mount over the rings – no need for removal of rings during installation All metric hardware allows easy replacement for misplaced screws 100571 Rings and troughs – preprovisioned jumper management ensures existing wiring is not disturbed during expansion or maintenance 10/03 • Cable tie down bars on the rear of the bay eliminate the need for filler panels and end guards 600 mm 600 mm Empty Skeleton Bay 600 mm width aligns perfectly with raised floor tile dimensions and simplifies office engineering and planning 600 mm Skeleton Bay Front Jumper Rings (shown with panels installed) Ordering Information Description Catalog Number Skeleton bay front cross-connect IBF-RSC021 Note: Bays come fully-loaded with cable troughs, cable rings, fuse panel and grounding kits The bay holds up to nine 7-inch (17.78cm) high modules www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 125 Mbps DSX Front Cross-Connect Solutions FlexDSX™ Introduction 10/03 • 100571 600 mm Products The FlexDSX platform from ADC embodies the ultimate flexibility in circuit access The 4-port jack card provides dual monitor capability Dual monitoring allows nonintrusive monitoring in both directions of a Mbps signal from a single DSX location Monitoring a circuit in both directions from a single DSX location will save time when troubleshooting the network because test gear isn’t moved to a second DSX location to test the complete circuit Dual monitoring also gives access to complete circuits when the other end of the cross-connection is not available, as in the situation where collocation of two carriers exists and the cross-connection between DSX provide the point of interconnection FlexDSX products also provide flexibility in deploying your resources The completely modular design allows you to deploy modules and chassis on an as-needed basis By creating a lineup of skeleton bays and filling the bays with chassis and modules only as needed, you can defer capital expenses until the equipment is ready to create a revenue stream In today's multinational, multiservice environment, FlexDSX products offer a variety of standard terminations From wire-wrap to coax to RJ45 connectors, FlexDSX products offer the option to terminate Mbps equipment from a single location Features • Conduct protocol testing for both OUT and IN transmission directions from one location – saves time when testing a circuit • Staggered jack alignment – allows industry standard patch cords to be used side-by-side in high density products • Jumper rings and rear cable bars are installed on the skeleton bay – provides superior cable management • OUT/IN equipment cable terminations on the backplane are modular in groups of four – allows for multiple circuit count configurations (56, 64, 84) • Works with twisted pair or coax cabling; choose wire-wrap, BNC or 1.6/5.6 interfaces – flexibility to meet a variety of needs • Coax and 120 Ohm connections provide the flexibility to connect 75 Ohm equipment to 120 Ohm equipment FlexDSX™ Application Network Element A LED Tracer Wire FlexDSX MON MON OUT Tx OUT M X-OUT X-OUT OUT IN OUT IN IN Rx IN X-IN MON PERMANENT EQUIPMENT CABLE Network Element B FlexDSX OUT O I IN Tx OUT Rx IN X-IN MON Typical DSX SemiPermanent Cross Connect Jumper PERMANENT EQUIPMENT CABLE Test Box FlexDSX products provide the convenience and time-saving feature of testing and monitoring the signal in both directions from one location www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 126 Mbps DSX Front Cross-Connect Solutions FlexDSX™ Panels – Four-Port (Dual Monitor) Jack Access FlexDSX Rear View (1.6/5.6 Balun version shown) FlexDSX Front View Large labels provide clear documentation of circuits 64-terminations per panel (Balun and twisted pair) – matches 2.048 Mbps equipment cabling breakouts Large front trough avoids cable build-up Chassis are configured with OUT/IN interfaces in groups of four for easy removal and minimal disturbance of adjacent circuits Staggered jacks allow industry standard patch cords to be used side-by-side Tracer LED eliminates manual tracing of circuits for faster circuit identification 100571 600 mm Products FlexDSX panels are the only DSX panels in the industry that offer individual, removable jacks, removable OUT/IN equipment cable terminations, and four-port (bidirectional) test access capabilities The four-port jack system consists of OUT and IN jacks for direct access to the network element’s input and output signals, and DUAL MONITOR jacks for monitoring of the signal in both directions simultaneously at a single location Dual monitors are especially beneficial for testing when the other side of the cross-connect is located far away, in another room, or is inaccessible (i.e., collocation) Four-port (dual monitor) jacks allow quick isolation of problems in larger applications where the cross-connect may be located far away or is inaccessible 10/03 • Individual removable jacks FlexDSX four-port jack card FlexDSX panel with individual jack card pulled out www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 127 Mbps DSX Front Cross-Connect Solutions FlexDSX™ Panels – Four-Port (Dual Monitor) Jack Access Ordering Information Catalog Number Description 10/03 • 100571 600 mm Products Fully-loaded, 64-circuit panel – Wire-wrap cross-connects 5.25" (13.34 cm) high, 19" (48.26 cm), EIA/IEC mounting 120 Ohm wire-wrap equipment interface 120 Ohm wire-wrap equipment interface, rear dual performance monitor BNC Balun equipment interface 1.6/5.6 Balun equipment interface SMB RJ45 Shielded RJ45 DFX-100001 DFX-100001-DPM DFX-210001 DFX-220001 DFX-230001 DFX-400001 DFX-500001 7" (17.78 cm) high*, 19" (48.26 cm), EIA/IEC mounting BNC equipment interface 1.6/5.6 equipment interface DFX-210001-DPM* DFX-220001-DPM* *The IBF-RSC024 skeleton bay holds nine 7-inch (17.78 cm) high panels Module and Card 4-Port Jack Card with 4-Pack Module 4-Pack Module with 1.6/5.6 connectors 4-Pack Module with wire-wrap connectors 4-Pack Module with BNC connectors 4-Port Jack Card Ordering Information Description Catalog Number FlexDSX 64-position empty chassis 19" (482.6mm) x 5.25" (133.35mm) (3RU) DFX-9E0002 4-pack modules Wire-wrap, front cross-connect, 120 Ohm BNC, front cross-connect, 75 Ohm 1.6/5.6, front cross-connect, 75 Ohm RJ45, front cross-connect, 120 Ohm Shielded RJ45, front cross-connect, 120 Ohm SMB, front cross-connect, 75 Ohm DFX-9E1000 DFX-9E2000 DFX-9E3000 DFX-9E4000 DFX-9E4000-S DFX-9E5000 Circuit cards FlexDSX jack, odd FlexDSX jack, even DFX-1 DFX-2 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 128 Mbps Digital Cross-Connect System All-Front-Access FlexDSX™ Panels 10/03 • 100571 600 mm Products The all-front-access FlexDSX product family, designed for 2.048 Mbps cross-connect applications for the standard 600 mm footprint, provides 0.045" (1.14 mm) square wire-wrap pin interface options on both the cross-connect and equipment fields and is available with or without performance monitoring Each chassis holds up to 16 four-circuit front access module packs No internal wiring is required between modules and the chassis or between adjacent modules Each of the 64 individual jack cards in a fully-populated chassis have four bantam-sized ports—monitor OUT, OUT, IN, and monitor IN, as well as a red flashing tracer lamp Monitor network resistors provide 120 Ohm impedance FlexDSX chassis without performance monitoring (Front View) Four-Pack Modules FlexDSX chassis with performance monitoring (Front View) Four-Pack Modules Ordering Information Description Catalog Number All-front-access FlexDSX panels Empty rack (holds 10 DFX-1F0001 chassis) Fully-loaded panel Empty chassis Four pack module DFX-RSFA04 DFX-1F0001 DFX-9E0003 DFX-9F1000 All-front-access FlexDSX with performance monitoring Empty rack (holds DFX-1F0001-DPM chassis) Fully-loaded panel Empty chassis Four pack module DFX-RSFA03 DFX-1F0001-DPM DFX-9E0003-DPM DFX-9F1000-DPM www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 129 Mbps DSX Front Cross-Connect Solutions PxPlus™ Panels – Three-Port Individual Jack Modularity PxPlus panel shown fully loaded with circuit cards PxPlus panel shown empty without circuit cards Large removable labels provide easy documentation of circuits to help avoid mistakes while trouble shooting Designed for individual jack modularity – jacks are ordered separately and installed upon service turn-up Tracer LED eliminates manual tracing of circuits for faster circuit identification Backplane can be fully prewired upon installation – allows circuit cards to be added as needed for true cost deferment 64 terminations per panel (Balun and twisted pair) matches equipment cabling breakouts Three-port (single monitor) jack access allows easy circuit access for testing, patching and monitoring 10/03 • 100571 600 mm Products The PxPlus panel was designed for Mbps DSX cross-connect applications where individual jack modularity is required The PxPlus system consists of a 64-circuit empty panel and individual three-port jack access cards that are sold separately The empty panel can be loaded into the bay and precabled When service is ready to be turned up, the PxPlus jack cards are installed into the panel providing for true cost deferment PxPlus Panel with individual jack card pulled out PxPlus panel (rear view) (Wire-wrap version shown) Ordering Information Description Catalog Number 64-circuit empty chassis – Wire-wrap equipment interface BNC Balun equipment interface PXP-532004 PXP-532003 Jack card Individual 120 Ohm www.adc.com • PXP-A00006 +32-2-712-65-00 • +32-2-712-65-42 130 Mbps DSX Front Cross-Connect Solutions DSX 64-Termination – Three-Port Fixed Panel Each panel supports 64 Mbps terminations and provides three-port jack access for monitoring, patching and testing An LED provides easy identification of cross-connect cables by eliminating manual tracing of wires The equipment (OUT/IN) cables are terminated on the rear of the chassis via wire-wrap and Balun options of 1.6/5.6 or BNC connectors The cross-connects are terminated on the front via wire-wrap pins 600 mm Products Features • • • • • 64 terminations per panel (Balun and twisted pair) – matches 2.048 Mbps equipment cabling breakouts All panels mount into the ADC 600 mm skeleton bay IBF-RSC021 – one platform for all applications Tracer LED eliminates manual tracing of cross-connect wires for fast circuit identification Oversized labels for complete circuit identification In-service patching and circuit rearrangement allows circuit maintenance to be completed during business hours without downtime by using ADC’s bridging office repeaters (Call your local ADC sales office for more information) • Balun terminations increase density by converting 75 Ohm equipment cables to 120 Ohm for crossconnecting while still providing the flexibility of DSX jack access Available in BNC and 1.6/5.6 DSX 64-Termination Panel (Rear View) (BNC Balun version shown) Front wire-wrap cross-connect pins for easy circuit rearrangement Large removable labels provide easy documentation of circuits to help avoid mistakes while troubleshooting 64-terminations per panel (Balun and twisted pair) – matches equipment cabling breakouts One part number allows for easy ordering and installation • 100571 DSX 64-Termination Panel (Front View) 10/03 Three-port (single monitor) jack access allows easy circuit access for testing, patching and monitoring Tracer LED eliminates manual tracing of circuits for faster circuit identification DSX 64-Termination Panel Ordering Information Description Catalog Number 64-termination panel 120 Ohm wire-wrap equipment interface BNC Balun to wire-wrap equipment interface 1.6/5.6 Balun to wire-wrap equipment interface www.adc.com • +32-2-712-65-00 D1M-1A2016 D1M-1A2015 D1M-1A2017 • +32-2-712-65-42 131 Mbps Digital Cross-Connect System Bay Hardware and Accessories End Guard These 2.2 m high end guards provide protection and a finished appearance at the start and end of the lineup Ordering Information Description Catalog Number RAC-EGK450* 600 mm deep end guard RAC-EGK600* 300 mm deep end guard RAC-EGK300* * Each kit comes with two end guards DSX Frame Doors The door kit provides left and right doors for the front and rear of the DSX frame Also included are top, front, and rear brackets for mounting of the doors to the frame Ordering Information Catalog Number Description IBF-1ENCDOR DSX frame door kit End Guard for Use with Door Enclosure Kit This end guard kit is used in conjunction with the DSX frame doors used to enclose the frame It also provides protection and a finished appearance to the start and end of the frame lineup Ordering Information Description Catalog Number End guard for use with DSX frame door kit IBF-1ENCEG 10/03 • 100571 600 mm Products 450 mm deep end guard Filler Panel Kits The filler panel kits add spacing between DSX frames The kits come in 150 mm and 300 mm measurements Ordering Information Description Catalog Number 150 mm filler panel kit SFK-122150 300 mm filler panel kit that includes upper and lower cable trough SFK-122300 www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 132 Mbps Digital Cross-Connect System Bay Hardware and Accessories Rack Installation Kit This rack installation kit comes with all the necessary hardware to install the DSX rack in a raised floor environment Ordering Information Description Catalog Number RAC-MX0615 Concrete floor kit 600 mm Products Zone raised floor mounting kit RAC-MX0616 Note: See installation guidelines for instructions on mounting the DSX Frame AC Outlet Kit This AC outlet kit is a universal continental Europe outlet that mounts in the base of the frame Ordering Information Description Catalog Number UK AC outlet kit AUX-AC0003 Continental Europe AC outlet kit AUX-AC0004 North American AC outlet kit AUX-AC0005 Cross Aisle Panels 10/03 • 100571 Ordering Information Description Catalog Number 128-circuit cross aisle panel AUX-200022 64-circuit cross aisle panel with trace LEDs AUX-200064 Alarm Panels Ordering Information Description Catalog Number 64-circuit all front access panel www.adc.com • +32-2-712-65-00 AUX-000040 • +32-2-712-65-42 133 Mbps Super High Density Solutions DSX600™ Bay ADC introduces the 600 mm Super High Density Bay (SHD) product line Quick to install, easy to manage and maintain, Super High Density Bays maximize the network’s termination density, simplifies engineering and is designed to match any application Perfectly ADC’s 600 mm Super High Density DSX – ensuring transparent service evolution 10/03 • 100571 600 mm Products Features and Benefits One part number ADC’s Super High Density (SHD) Bay comes preassembled to the customer’s specification, eliminating multiple parts and lineup hardware This reduces installation time, simplifies ordering, and helps generate revenue faster by turning up service sooner Waterfall IN/OUT cabling Waterfall cabling increases lineup density, thereby saving valuable floor space and reducing cost by eliminating the need for bay spacers 600 mm width The bay’s width aligns perfectly with raised floor tile dimensions, simplifying office engineering and planning Integrated trouble-free cross-connect cable management Providing increased jumper capacity, ADC’s patented cable management system eases operations and maintenance by reducing cross-connect jumper congestion Expanded labeling space Decreases possibility of mistakes during troubleshooting as all circuits are clearly identified 64-position panels Panel termination count matches digital switch and fiber optic multiplexer Mbps signal groups for simplified network engineering 1152 wire-wrap or 768 BNC terminations Industry's highest DSX density improves profitability by conserving valuable floor space Helps providers realize more revenue and have more space for other revenue-generating network equipment 192 cross aisle tie circuit Integrated cross aisle tie panels ensure ability to add new lineups without sacrificing overall termination density Single or dual bantam monitor ports Streamlines installation, maintenance and troubleshooting Supports traditional monitoring practices as well as monitoring on OUT (Tx) and IN (Rx) ports of the DSX Overhead and raised floor cabling Provides flexibility for any installation criteria www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 134 Mbps Super High Density Solutions 10/03 ADC’s Super High Density Bay (SHD) comes preassembled to customer specification, eliminating multiple parts and lineup hardware This reduces installation time, simplifies ordering and saves money Waterfall cabling increases lineup density, thereby saving valuable floor space and reducing cost by eliminating the need for costly bay spacers 600 mm 600 mm With its 600 mm width, ADC’s SHD bay aligns perfectly with raised floor tile dimensions simplifying office engineering and planning By providing increased jumper capacity (a), ADC’s patented cable management system (b) eases operations and maintenance by reducing cross-connect jumper congestion This makes removal of inactive jumpers easy • 100571 600 mm Products DSX600™ Bay a b www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 135 Mbps Super High Density Solutions DSX600™ Bay Labeling is critical to troubleshooting efforts ADC’s SHD Bay allows technicians to clearly identify each circuit by providing expanded labeling space to improve network documentation and decrease the potential for mistakes while troubleshooting 600 mm Products 100571 10/03 www.adc.com • +32-2-712-65-00 • The SHD Bay utilizes 64-termination panels to match digital switch and fiber optic multiplexer two megabit signal groups, simplifying network engineering • With (1152) Mbps terminations and 192 cross aisle terminations, ADC’s SHD Bay provides the industry's highest DSX density available, saving money by conserving valuable floor space In situations where 75 Ohm terminations are required, ADC provides a 768 termination bay which fits in the same lineup as the 120 Ohm bay and maintains the advantage of ADC’s patented cross-connect jumper management +32-2-712-65-42 136 Mbps Super High Density Solutions DSX600™ Bay Ordering Information Dimensions (HxWxD) Description Catalog Number 2.13 m 2.13 m x 600 mm x 457 mm SHD-0323 768 Mbps terminations 75 Ohm BNC OUT/IN interface Wire-wrap cross-connect interface Designed for below floor cabling Super High Density Bay end guard 2.13 m x 600 mm x 457 mm SHD-0424 SHD-0007 2.2 m 1152 Mbps terminations 64 cross aisle tie circuits Dual monitor panels 32 interbay circuits Designed for below floor cabling 2.2 m x 600 mm x 457 mm SHD-W-0001 1152 Mbps terminations 192 cross aisle tie circuits Wire-wrap OUT/IN interface Wire-wrap cross-connect interface Designed for overhead cabling 2.2 m x 600 mm x 457 mm SHD-0512 1344 Mbps terminations 120 Ohm BNC OUT/IN interface Wire-wrap cross-connect interface Designed for below floor cabling Super High Density Bay end guard 2.2 m x 600 mm x 457 mm SHD-0051 SHD-W-0005 Super High Density Bay raised floor installation kit (for 600 mm floors) SHD-HR-28 Super High Density Bay raised floor installation kit (for 850 mm floors) SHD-HR-55 Concrete floor installation kit RINST-FLR 10/03 • 100571 600 mm Products 1152 Mbps terminations 192 cross aisle tie circuits Wire-wrap OUT/IN interface Wire-wrap cross-connect interface Designed for below floor cabling Super High Density Bay Front View Super High Density Bay Rear View (Note: This application shows overhead cabling This configuration is available upon request.) www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 137 Mbps Super High Density Solutions FlexDSX™Super High Density Bay Introduction ADC’s FlexDSX Super High Density Bay design is unmatched in the marketplace ADC’s vertical IN/OUT terminal blocks with extra cabling space and cable management fanning strips provide 50 percent more cabling space than traditional high-density bays Simultaneously, it provides increased jumper capacity to simplify cross-connect wire management for easy operation and maintenance The FlexDSX Super High Density design incorporates a recessed vertical wireway for cross-connect cabling and up to seven horizontal cross-connect jumper wireways instead of the standard two wireways Vertical and horizontal wireways are on separate planes to avoid congestion and pile-up at intersections The FlexDSX Super High Density Bay enables service providers to realize additional cost savings by conserving valuable floor space The bay provides more than 30 percent floor space savings, while doubling the density and provides dual monitoring with ADC’s reliable FlexDSX jack technology Description The FlexDSX Super High Density Bay achieves greater density in a 7-foot height x 26-inch width x 18-inch depth, accommodating up to 1512 (7') usable DSX jack terminations ADC’s flexible ordering guide allows bay designs in 64 or 84 jacks per panel This eliminates jack waste or complications in circuit management administration • Provides clear identification of each circuit by offering expanded labeling space improving network documentation and decreasing potential mistakes while troubleshooting • Colored cross-connect labels allow for easy determination of circuit terminations 10/03 • 100571 600 mm Products ADC’s FlexDSX™ Super High Density Bay offers greater termination density as well as built-in, trouble-free cable management for flexible network planning, installation and maintenance • Flashing LED and Dual monitoring www.adc.com • • Block’s design provides better cable management and more space for cables • Cable entry is allowed on both sides of block +32-2-712-65-00 • +32-2-712-65-42 138 Mbps Super High Density Solutions FlexDSX™Super High Density Bay Description 10/03 • 100571 600 mm Products • 1512 jacks per seven-foot bay uses an efficient jack count of 84 jacks per panel Dual monitoring of the out and in ports, panel termination count matches digital switching broadband equipment for simplified network engineering Consists of 18 panels of 84 jacks in a single plane • More than 30 percent floor space savings – the industry’s highest DSX density improves profitability by conserving valuable floor space Service providers can realize more revenue and more space for other revenue generating network equipment • Incorporating vertical IN/OUT terminal blocks with extra cabling space and cable management strips provide 50 percent more cabling space than traditional high-density bays Increased lineup density saves valuable floor space and reduces costs by eliminating the need for bay spacers Dual hinged doors with designation labels on both sides provide double the designation space Adhesive backed labels guarantee the identification designations will always be available The expanded label space minimizes the possibility of mistakes during trouble shooting as all circuits are clearly identified • Built-in trouble-free cross-connect cable management provides increased jumper capacity ADC’s cable management system eases operations and maintenance by reducing crossconnect jumper congestion and pileup • Tie pair terminal blocks (2) 80 circuits wired point-to-point to tie pair blocks in the rear cross-connect field by ADC Built-in aisle tie panels ensure ability to grow new lineups without sacrificing overall termination density • The rear cross-connect high density design allows for all jack maintenance activities to remain at an arm’s length • Guarantees a worry-free maintenance environment with over 40 years of proven jack quality and reliability and a lifetime warranty All components of the bay are made by ADC, ensuring quality from beginning to end Super High Density Bay Ordering Information # of # of Cross Terminations Aisle Circuits Jack Position Description 7' concentration bay, overhead cabling 7' maintenance bay, overhead cabling 7' maintenance bay, raised Floor cabling 7' concentration bay, raised Floor cabling 2.2m concentration bay, overhead cabling 2.2m maintenance bay, overhead cabling 1512 1512 1260 1260 1152 960 84 84 84 84 64 64 160 160 160 160 160 160 Catalog Number DFX-SHD001 DFX-SHD002 DFX-SHD003 DFX-SHD004 DFX-SHD005 DFX-SHD006 *Overhead cabling denotes the cable enters the top of the bay and the equipment termination blocks are at the top of the bay Raised floor cabling denotes the cable enters from the raised floor into the bottom of the bay and the equipment blocks are at the bottom of the bay www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 139 Mbps Super High Density Solutions FlexDSX™ Super High Density Bay Accessories Ordering Information Catalog Number AC outlet kit (FlexDSX Super High Density Bays accept outlet kits in front only, North American) ACOK-PWNB End guards 7' height x 18.75" width 2.2 m height x 18" width, 600mm rack SHD SHD-HR-85 SHD-HR-92 Installation kits SHD-HR-43N SHD-HR-44N SHD-HR-91 RINST-FLR SHD-HR-93 7' to 9' extension rack 7' to 11.5' extension rack Installation kit, raised floor Installation kit, concrete floor, overhead cabling Installation kit, raised floor, metric 10/03 • 100571 600 mm Products Description www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 140 Mbps Super High Density Solutions Accessories Bantam Patch Cords Ordering Information Description Catalog Number 10/03 • 100571 600 mm Products Three conductor* Single 1' (.3 m) 1.5' (.46 m) 2' (.61 m) 2.5' (.76 m) 3' (.91 m) 4' (1.22 m) 5' (1.52 m) 6' (1.83 m) PJ712 PJ713 PJ714 PJ715 PJ716 PJ718 PJ720 PJ722 PJ1208 PJ1210 PJ1212 PJ1415 PJ1420 PJ1425 PJ1430 PJ1450 8' (2.44 m) 10' (3.05 m) 12' (3.66 m) 15' (4.57 m) 20' (6.1 m) 25' (7.62 m) 30' (9.15 m) 50' (15.24 m) Dual* 1' (.3 m) 2' (.61 m) 2.5' (.76 m) 3' (.91 m) 4' (1.22 m) 5' (1.52 m) 6' (1.83 m) 8' (2.44 m) 10' (3.05 m) 12' (2.66 m) 14' (4.27 m) 20' (6.1 m) 25' (7.62 m) 30' (9.15 m) 35' (10.68 m) 45' (13.73 m) PJ768 Three-Conductor Dual Patch Cord PJ762 PJ764 PJ765 PJ766 PJ768 PJ770 PJ772 PJ1308 PJ1310 PJ1312 PJ1514 PJ1520 PJ718 Three-Conductor Single Patch Cord PJ1525 PJ1530 PJ1535 PJ1545 Patch cord kit International patch cords kit ACK-INTL International patch cords kit, nickel-plated ACK-INTL-N * For nickel plated patch cords, add the suffix “N” For plenum-rated fire retardant patch cords, add the suffix “PL” www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 141 Mbps Super High Density Solutions Accessories Tools and Tool Kits Ordering Information Catalog Number Manual wire-wrap kit includes: Manual wire-wrap kit 22-24 AWG wire-wrap bit sleeve 24-26 AWG wire-wrap bit sleeve 22-24 AWG wire-wrap bit 26 AWG wire-wrap bit Mannual wire-cutting/stripping tool Manual unwrapping tool (screw driver tool) Manual unwrapping tool (soft, ergonomic handle) Unwrapping sleeve for use with AUX-0X0381 Electric 220 wire-wrap gun 22-24 AWG bit (0.64 - 0.51mm) 22-24 AWG sleeve (0.64 - 0.51mm) AUX-0X0165 AUX-0X0803 AUX-0X0802 AUX-0X0381 AUX-0X0383 AUX-0X0466 AUX-0X0467 AUX-0X0468 Cross-Connect Wire Ordering Information Description Cross-connect Cross-connect Cross-connect Cross-connect Catalog Number wire, wire, wire, wire, 500-foot roll (150 m) 1000-foot roll (300 m) 1500-foot roll (450 m) 2000-foot roll (600 m) DSX-CCW/500 DSX-CCW/1000 DSX-CCW/1500 DSX-CCW/2000 10/03 • 100571 600 mm Products Description www.adc.com • +32-2-712-65-00 • +32-2-712-65-42 142 ... www.adc.com • + 32- 2-7 12- 65-00 • + 32- 2-7 12- 65- 42 124 Mbps DSX Front Cross-Connect Solutions ADC 600 mm Skeleton Bay for FlexDSX™, PxPlus™ and DSX6 4 Panels 600 mm Products The 600 mm skeleton bay.. .2 Mbps DSX Front Cross-Connect Solutions 600 mm Mbps DSX Product Family The Products FlexDSX™ Panel PxPlus™ Panel Loaded 600 mm Skeleton Bay Empty 600 mm Skeleton Bay DSX 64-Termination... high modules www.adc.com • + 32- 2-7 12- 65-00 • + 32- 2-7 12- 65- 42 125 Mbps DSX Front Cross-Connect Solutions FlexDSX™ Introduction 10/03 • 100571 600 mm Products The FlexDSX platform from ADC embodies