Q UAD F IBER L OOP C ONVERTER AND M OUNTING C HASSIS The Quad Fiber Loop Converter System from ADC. The T1/E1 Service Delivery Experts QFLC Module and Wall Mount Chassis 2-Position Rack Mount Chassis QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer Description ADC has designed a family of Fiber Loop Converters (FLCs) that provides a cost-effective alternative to deploying service over copper while avoiding the high capital investment of DS3 fiber optic terminals. This family includes products designed for economical distri- bution of single or multiple DS1s. The Quad FLC multiplexes up to four T1s for transport over two fibers at distances of 16 to 20 miles (26 to 33 km). The QFLC system consists of a rack mounted central office chassis and a wall mounted customer premises chassis. In contrast to M12/M13 fiber optic terminal sys- tems (FOTS), which require a variety of modules to start up operation, the QFLC mod- ule is a stand-alone system and does not require additional plug-in equipment. The QFLC was designed to be installed quickly. Plug, play and walk away installation is a reality with the QFLC. Extensive, built-in self-test circuitry allows the QFLC to isolate module failures and alert maintenance personnel via standard office alarms. The optional microprocessor unit (MPU), residing in the 8 position rack mount chassis, collects alarm information from all remote and local QFLC modules for connection to alarm surveillance equipment with a Telemetry Byte Oriented Serial Interface (TBOS). The QFLC supports 1+1 redundancy to protect against single point failures of both opti- cal facilities or electronic equipment. The QFLC features two sets of bit error rate (BER) threshold select switches. These switches enable the user to select the BER at which the module will 1) declare a minor alarm to indicate that the BER has exceeded an early warning level and 2) initiate protection switching in a system configured in a protect mode. The BER threshold at which protection switching occurs may be set according to the performance levels guaranteed to your customers. All of ADC’s FLC products feature the option to provide 60 mA simplex current, which can be turned on and off by the user depending on the needs of a particular installation. This feature allows the QFLC to supply span current on a DS1 output to power channel service units (CSUs) or • Chassis supports optical hubs and is compatible with ADC’s entire FLC family of O/E products Mechanical housing can accommodate a wide variety of plug-in modules. From single DS1 to multiple DS1s, or mixing DS1s with DS3s, the chassis provides a broad platform from which new services can be delivered. A variety of high capacity circuits can now be distributed from a single chassis. • Single module system No need to inventory different working and protect modules, or different near and far-end modules. One part number does it all, reducing investment in spare inventory and simplifying circuit provisioning and installa tion. • Optional 1+1 redundancy Protection against fiber facility or equipment failures. Unprotected circuits can be upgraded later to provide protection, thereby lowering the initial cost of installation. • Dual selectable BER threshold setting Provides selectable BER thresholds for protection switching and early warning minor alarm. Switching and minor alarm levels can be set according to service requirements. • 60 mA simplex current on DS1 outputs Provides span power on an as needed basis for powering network interface devices or channel service units. This eliminates the need for most span powering repeaters at the customer premises, saving money and installation time. Features and Benefits QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer Features and Benefits (cont'd) • Remote (far-end) alarms can be displayed locally Simplifies trouble diagnostics and allows single-ended trouble shooting. This reduces field dispatches and improves responsiveness to potential service interruption. • Remote housekeeping alarm transport Housekeeping alarm inputs provide monitoring of external equipment at the remote site, such as fire and door alarms. Reduces investment in external alarm reporting systems. • Individual DS1 remote loop back capability Allows single-ended testing of each DS1 link to aid in trouble sectionalization. • Redundant AC power converters at customer premises Two AC/DC converters are available in the wall mount chassis to ensure that service is not interrupted if a supply should fail. For an enterprise in today’s highly competitive world, communications and the ability to effectively manage information are seen as strategic components in developing and maintaining a competitive edge. Growing demands for faster service, more features and higher quality mean that service providers must design a migration strategy for their networks that not only addresses today’s needs but also anticipates tomorrow’s. The Quad Fiber Loop Converter provides a solid foundation for future products and services. By installing the chassis at a central location, service providers can support multiple customers in a variety of applications. Since the chassis supports all FLC modules, including the DS3 FLC, modules can be mixed or matched depending on service requirements. Described on the following pages are several applications which take advantage of the flexibility in the Fiber Loop Converter sys- tem. HUT BUILDING HIGH RISE BUSINESS PARK POINT-TO- MULTIPOINT CENTRAL OFFICE Hut REH REMOTE PEDESTAL REH REMOTE PEDESTAL • Optional wall mount battery back-up Provides a minimum of 8 hours back-up in the event of commercial power failure, ensuring uninterrupted service. QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer For an enterprise in today’s highly competitive world, communications and the ability to effectively manage information are seen as strategic components in developing and maintaining a competitive edge. Growing demands for faster service, more features and higher quality mean that service providers must design a migration strategy for their networks that not only addresses today’s needs but also anticipates tomorrow’s. The Quad Fiber Loop Converter provides a solid foundation for future products and services. By installing the chassis at a central location, service providers can support multiple customers in a variety of applications. Since the chassis supports all FLC modules, including the DS3 FLC, modules can be mixed or matched depending on service requirements. Described on the following pages are several applications which take advantage of the flexibility in the Fiber Loop Converter system. HUT BUILDING HIGH RISE BUSINESS PARK POINT-TO- MULTIPOINT CENTRAL OFFICE Hut REH REMOTE PEDESTAL REH REMOTE PEDESTAL Applications Point-to- Multipoint Providing fiber-based DS1 services in urban applications requires low first cost installa- tion and the capability to serve multiple customer locations. By placing the rack mount chassis in the central office, up to eight different customer locations can be served from a single platform. Service turn-up is fast, as one plug-in part number is all you need, whether the service is 1:1 protected or unprotected. CENTRAL OFFICE POINT-TO- MULTIPOINT DS1 ELECTRICAL CENTRAL OFFICE DSX FDPQFLC OFFICE BUILDING OFFICE BUILDING OFFICE BUILDING QFLC N I D QFLC N I D QFLC N I D OFFICE BUILDING QFLC N I D QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer Remote Pedestals As fiber deployment extends into the loop, remote pedestals and cabinets are being fed with fiber optic cable from a hut or central office. The QFLC is ideal for this application, providing up to 8 DS1s in a 4" chassis, well-suited for a digital loop carrier system. CENTRAL OFFICE HUT REH REMOTE PEDESTAL REH REMOTE PEDESTAL To Central Exchange Remote Pedestal Hut 1 - 240 Homes • • • E1 Electrical QFLCDDF FDP 1 - 240 Homes • • • FOT QFLC ICX Remote Pedestal QFLC ICX Suburban Business Parks With the installation of an eight position rack mount shelf in a CO or CEV, a service provider can support multiple customers, each of which would have a wall or rack mount chassis on their premises. The QFLC allows the service provider to take advan- tage of any unused fiber already terminated at the building premises, thereby providing T1 service in the most economical means possible. By using the span power option on the QFLC, the service provider can eliminate the need for an additional office or span repeater to power the customer’s equipment. As the customer’s service requirements become more critical, the service provider can install an additional QFLC on each end of the link to fully protect the system. CENTRAL OFFICE HUT BUSINESS PARK WAREHOUSE TO CENTRAL OFFICE DS1 ELECTRICAL HUT FOT DSX FDPQFLC OFFICE BUILDING FACTORY QFLC QFLCQFLC QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer High Rise Customer Premises DS1 Distribution The Fiber Loop Converter family makes all-fiber building risers an economical reality. Referencing the application drawing below, you can see many possible configurations that allow for fiber drops on each floor. An M13 FOTS can be located in the basement of a high rise building and the DS1s can be deployed to the various floors of the building via QFLC modules. A series of wall mount chassis can be mounted in the wiring closets of each floor. In all situations, an AC power recep- tacle is all that is required to power the units; battery back- up is also available. CENTRAL OFFICE BUILDING HIGH RISE TO CENTRAL OFFICE DS1 ELECTRICAL FOT DSX QFLC C S U C S U QFLC QFLC BUILDING HIGH RISE PHYSICAL DESCRIPTION Dimensions QFLC Module: Wall Mount Chassis: Rack Mount Chassis: WEIGHT QFLC Module: Wall Mount Chassis: Rack Mount Chassis: ENVIRONMENTAL Temperature Operating: Storage: Humidity Operating: Storage: ELECTRICAL Input Frequency: Input Level: Output Frequency: Interface Standard: Output Signal: Line Build-Out: OPTICAL Wavelength: Line Rate: Transmit Device: Transmit Power: Connector: Cable: Receiver Dynamic Range: Receiving Device: Optical Budget: BER Threshold for Protection Switching: Minor Alarm: 10.75 x 1.4 x 10.0 inches (27.3 x 3.6 x 25.4 cm) 16.88 x 15.92 x 9.58 inches (42.87 x 40.43 x 24.33 cm) 15.70 x 19.00 or 23.00 x 11.71 inches (39.90 x 48.26 or 58.42 x 29.70 cm) 1 lbs 3 oz (.54 kg) 45 lbs. (20.45 kg) 40 lbs. (18.18 kg) -40°C to 65°C (-40°F to 149°F) -40°C to 70°C (-40°F to 158°F) 20 to 80% (no condensation) 10 to 95% (no condensation) 1.544 Mbps ± 200 bps 0 to -6.0 dB; shaped line loss relative to nominal DSX-1 level 1.544 Mbps ± 200 bps DSX-1 Bipolar (B8ZS or Alternate Mark Inversion) Within DSX-1 template and level standard (Meets TR-TSY-000499) Five selectable ranges 0' to 655' 1305 ± 35 nm 6.312 Mbps Singlemode Laser Diode -3 to -9 dBm (Average Power) FC/Ultra PC, SC/Ultra PC 9/125 µm singlemode -4 to -31 dBm PIN Photodiode 22 dB (minimum) 8.5 x 10 -4 to 1 x 10 -10 1 x 10 -6 to 1 x 10 -10 QFLC and Mounting Chassis Specifications QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer -42 to -56 Vdc 336 mA maximum 600 mA maximum 0 to -42 Vdc at -48 Vdc input 375 mA Specifications Description QFC-D3LDFC QFC-D3LDSC FLC-A10MPU FRM-RAW08A FRM-FAW08A FRM-FAW02B FRM-OPM/KIT FRM-FAW02D Quad Fiber Loop Converter module Extended temperature (-40° C t 65° C) Two modules required (one at each end) to multiplex up to 4 T1s for transport over 2 singlemode fibers; redundancy (1+1) supported by supplying 2 modules at each end, and enabling the option on modules and chassis. FC connector SC connector Microprocessor unit (optional) Only used in 8 position rack mount chassis Rack mount chassis 8 position* rear access chassis, wire-wrap connections front access chassis, wire-wrap connections 2 position chassis, QFLC only 23" rack mounted (2 rack spaces) 23" rack mounted (2 rack spaces) with wall mount kit and OPM splice kit 19" rack mounted (2 rack spaces) Ordering Information Catalog Number QFLC and Mounting Chassiss 437 10/97 Original © 1997 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer Specifications published here are current as of the date of publication of this document. Because we are continuously improving our products, ADC reserves the right to change specifications without prior notice. At any time, you may verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications, Inc. views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products or features contained herein may be covered by one or more U.S. or foreign patents. ADC Telecommunications, Inc. P.O. Box 1101 Minneapolis, Minnesota 55440-1101 FAX: (612) 946-3292 From North America, Call Toll Free: 1-800-366-3891, Ext. 3223 Outside of North America: 612-938-8080 Home Page Address: http://www.adc.com International Sales Offices: Brussels, Belgium 32-2-712-6500 • United Kingdom 44-1189 879200 • Dusseldorf, Germany 49-211-530-655-0 Madrid, Spain 34-1-361-01-68 • Sydney, Australia 61-2-9975-1499 • Singapore 65-225-8228 • Beijing, China 86- 10-6500-7001 • Seoul, Korea 82-2-333-8989 • Bangalore, India 91-80-671-0230 • Malaysia 603-254-0025 Bangkok, Thailand 662-231-8316 • Philippines 632-892-4476 • Sao Paulo, Brazil 55-11-3040-0666 • Buenos Aires, Argentina 541-788-8700 • Mexico City, Mexico 525-658-4519 • Venezuela 58-2-286-1444 • Miami Lakes, FL (Caribbean/Miami) 305-231-8742 • Montreal, Quebec (514) 677-9166 Vancouver, BC (604) 270-1675 Toronto, Ont. (905) 629-3104 • Ottawa, Ont. (613) 599-5729 Ordering Information FWM-RJA04A FWM-WWA04A FWM-RJD04B FWM-WWD04B FWM-RJX04A FWM-WWX04A FLC-HDW007 FLC-HDW005 FLC-HDW006 FLC-HDW008 FLC-AC/BB2 FLC-HDW009 FLC-HDW010 FPC-SPD4/PFC-S-XM FPC-SPFC/BIC-S-XM FPC-SPFC-S-XM FPC-SPSC-S-XM Wall mount customer premises chassis Supports up to four QFLC modules, or a combination of QFLC and DS3 FLC modules 4 position, dual redundant AC power supply RJ48X modular jack access (customer side) Wire-wrap connections 4 position with battery back-up RJ48X modular jack access (customer side) Wire-wrap connections 4 position, no power supply RJ48X modular jack access (customer side) Wire-wrap connections Chassis accessories Vertical wall mount kit for 2 position chassis Swing out bracket for 4 position wall mount chassis Rack mount bracket for battery back-up or 4 position chassis Blank front panel kit for 8 position chassis AC power supply and battery back-up system 12.7 amp hours, UL94-V0 3 amp; intended for 2 position chassis Rack mount adapter kit for FLC-HDW009 Patch cords When ordering patch cords, replace X with length of patch cords. Standard length is 6m (20'); other sizes available upon request. D4PC-FCPC FCPC-Biconic FCPC-FCPC SCPC-SCPC Description Catalog Number . ONVERTER AND M OUNTING C HASSIS The Quad Fiber Loop Converter System from ADC. The T1/E1 Service Delivery Experts QFLC Module and Wall Mount Chassis 2-Position. anticipates tomorrow’s. The Quad Fiber Loop Converter provides a solid foundation for future products and services. By installing the chassis at a central location,