PREPARING THE SHAFT FOR DETAILED DRAWING 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN SHAFT DETAILED DRAWING Pro/ENGINEER Wildfire 2.0 Dr. Herli Surjanhata PREPARING THE SHAFT FOR DETAILED DRAWING Open shaft.prt, and make sure you have the saved view ISO_1. Create A Cosmetic Curve And An Axis Through The Curve Portion Of The Keyway From Insert pull down menu, select Cosmetic -> Sketch Click Done. 2 Select FRONT as sketching plane, then click Okay. Select Top in the SKET VIEW menu, and pick the TOP datum plane. Select the curved end of the sledgerunner keyway as a reference. Pick this curve for reference. 3 Sketch a circle as shown. Click . Create An Axis Thru The End Of Keyway Click , and pick the curved end of the sledrunner keyway. 4 CREATE A DETAILED DRAWING OF THE SHAFT Select the Create new object icon Choose Drawing from the New dialog box. Enter the name shaft. Uncheck the Use default template. Click OK button. Accept SHAFT.PRT as default model, and click Browse button to pick c.frm format. Select Open. Click OK button. 5 Create FRONT, TOP, RIGHT-SIDE, ISOMETRIC and Detailed views of the shaft as describe and shown below. Create The First FRONT View Of The Shaft Click to insert drawing view of the shaft. The message prompt to Select CENTER POINT fro drawing view, and pick a location near the middle left of the drawing – see Figure. The Drawing View dialog box opens. Under Model view names, select FRONT from the list. Click OK. Turn off the datums and coordinate system. , and click to redraw. Unlock the movement of drawing views. 6 Right-click the graphics area, and select Lock View Movement. Now the view can be moved Or click to unlock or lock the drawing views. Create A Projected RIGHT-SIDE View Of The Shaft Click the FRONT view, then right-click and select Insert Projection View. Pick a location to the right of the front view. Create A Projected TOP View Of The Shaft 7 Click the FRONT view, then right-click and select Insert Projection View. Pick a location to the top of the front view. Create A Scaled ISOMETRIC View Of The Shaft Click to insert drawing view of the shaft. Pick a location near the upper right-hand corner of the drawing. Under Model view names, select ISO_1 from the list. Click Apply. 8 Select Scale under Categories. Pick Custom Scale. Enter 0.5 as scale for view. Click OK. Create A Detailed View Of Snap Ring Groove 9 From Insert pull-down menu, select Drawing View -> Detailed. Pick a point on the top view in the center of the snap ring groove. The boundary of the detailed view are defined with a spline. To sketch a spline, pick points around the center point to define the view boundary. Press middle mouse button to finish. Pick a location above the snap ring groove on the top view. The detailed view appears. Be sure to move the detailed view and notes to best location – see figure. Pick a point here. [...]... dimension the axial locating dimension for the snap ring groove from the end of shaft rather than from the shoulder Redefine the shaft so that the correct dimension exists in the part model Open the SHAFT. PRT Pick the revolved cut in the Model Tree, right-click and select Edit Definition Select Placement -> Edit Click 29 Click and select from the Section dialog box Click to finish Save the part and close the. .. Zoom into the detailed drawing Pick the snap ring groove Click OK While Sel to Remove button is selected, pick the 0.60 dimension to remove it Click OK Pick the keyway and the snap ring groove in the top view, then click OK 14 Show Axes in the Drawing Toggle the Dimension button off and the Axis button on Under Show By, select View Pick the front view and click the Accept All button Pick the top view... desired location Pick the text in the detail note and move it to the center of detailed view 20 To move the extension lines, pick the dimension, then press and hold left button of the mouse on the extension line, and move it up The result is shown below The result after clean up is shown below 21 Create a Section View for Dimensioning the Keyway Depth and Width 22 Click the front view, then right-click... To move the numerical value of the dimension to the left Pick the dimension, and hover the cursor over one of the two red squares The cursor changes to two arrows symbol Press left mouse button, and bring the dimension to the left To move dimension text, left-click the dimension, and bring the cursor over the numerical value of the dimension, press left mouse button, and bring the dimension to the desired... Save the part and close the shaft. prt window Activate the shaft. drw window to open the Show/Erase dialog box Zoom in the detailed view, and click When the dialog box opens, verify that the Show and Dimension buttons are selected Select Feature and View in the Show By section Pick the snap ring groove in the detailed view Click OK, and select Accept All Close the dialog box Move the position of new dimension... select Accept All, then click Close Move the R.03, 45º x 02 and 45º x 03 to the new position located in the top area of the top view – see figure Pick the 45º x 02 dimension, rightclick to activate the Right Mouse Button short cut menu and select Edit Attachment Pick the new location as shown below 31 Repeat the same technique for other dimensions Move the dimensions if necessary The resulted rearrangement... view and click the Accept All button Pick the right view and click the Accept All button Pick the detailed view and click the Accept All button Zoom in to the right side view Click the Erase button, and Axis button Under Erase By, select Selected Items Pick the small transverse axis through the sledrunner keyway to remove it 15 Show the Surface Finish Symbols Toggle the Axis icon off and the Surface Finish... highlighted dimension to the desired location Right-click and select Properties 18 Pick Move Text button Move the numerical value of the dimension to the left 19 Pick the 3.00 keyway length, and move it to the front view Right-click and select Move Item to View Pick the front view By default, the movement of drawing views with the mouse is disallowed So, to move the view , and now the view can click be... Yes Erase the Cosmetic Curve from Isometric, Top and Right Side Views Select Erase, and toggle the Surface Finish icon off and the Cosmetic icon on Under Erase By, select View, and pick the isometric view, the top view and the right side view The only cosmetic curve remaining is on the front view Close the Show/Erase dialog box 16 Clean Up the Drawing Dimensions Click Pick front, top, and detailed. .. OK Accept the default offset and increment values Click Apply Click Close Switch the Diametral Dimensions to the Top View Zoom in on the front and top views Pick the four diametral dimensions Right-click, and select Move Item to View Pick the top view The dimensions move 17 Move the diametral dimensions underneath the top view To move the dimension, click the dimension, left-click and move the highlighted . PREPARING THE SHAFT FOR DETAILED DRAWING 1 ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN SHAFT DETAILED DRAWING Pro/ENGINEER Wildfire. Surjanhata PREPARING THE SHAFT FOR DETAILED DRAWING Open shaft. prt, and make sure you have the saved view ISO_1. Create A Cosmetic Curve And An Axis Through The