Đang tải... (xem toàn văn)
tài liệu hướng dẫn cách vẽ trong Mastercam X3 có hình ảnh và hướng dẫn cụ thể
Indexing (Tombstone & Chuck) Training Tutorials X³To order more books:Call 1-800-529-5517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X³ Training Tutorials – Indexing (Tombstone & Chuck)- Mill ApplicationsDate: Oct,20 2008Copyright © 1984 - 2008 In-House Solutions Inc. - All rights reserved.Software: Mastercam Mill X³Authors: Mariana LendelISBN: 978-1-926566-14-6NoticeIn-House Solutions Inc. reserves the right to make improvements to this manual at any time and withoutnotice.Disclaimer Of All Warranties And LiabilityIn-House Solutions Inc. makes no warranties, either express or implied, with respect to this manual or withrespect to the software described in this manual, its quality, performance, merchantability, or fitness forany particular purpose. In-House Solutions Inc. manual is sold or licensed "as is." The entire risk as to itsquality and performance is with the buyer. Should the manual prove defective following its purchase, thebuyer (and not In-House Solutions Inc., its distributor, or its retailer) assumes the entire cost of allnecessary servicing, repair, of correction and any incidental or consequential damages. In no event will In-House Solutions Inc. be liable for direct, indirect, or consequential damages resulting from any defect inthe manual, even if In-House Solutions Inc. has been advised of the possibility of such damages. Somejurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental orconsequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. All rights are reserved.This document may not, in whole or part, be copied, photocopied, reproduced, translated or reduced to anyelectronic medium or machine readable form without prior consent, in writing, from In-House SolutionsInc.TrademarksMastercam is a registered trademark of CNC Software, Inc.Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation;Mastercam Verify is created in conjunction with Sirius Systems Corporation; Windows NT and WindowsXP are registered trademarks of Microsoft Corporation. TABLE OF CONTENTSGetting StartedTombstone Project Using WCSTombstone With Multiple Fixtures On Each FaceChuck Indexing ProjectMastercam NotesA1112131B1 X³ TOMBSTONE PROJECTAbout Construction Plane (Cplane)The Cplane is a flat, two dimensional plane on which you create geometry and that can be definedanywhere in three dimensional space.There are 8 predefined construction planes in Mastercam. They are the same as the Graphic Views(Gviews).View 1 =View 2 =View 3 =View 4 =View 5 =View 6 =View 7 =TopFrontBackBottomRight SideLeft SideIsometricTo set the desired Cplane, choose Plane, from the Status Bar, and select the desired Cplane.You can also work in a 3D plane that allows you to draw in unrestricted 3D space. You can use the3D plane while creating geometry that can be related with existing geometry. For example, if youcreate a line knowing the endpoints or trimming entities up to other entities.To set the 3D plane, choose 3D from the Status Bar.STEP 2:CREATE THE CIRCLES IN THE FRONT CONSTRUCTION PLANE.Select Planes in the Status Bar.Select Front.Change the current construction Z depth to 5.0 by entering the value in the Status Bar as shown.CreateArcCircle Center PointPage 1 8 X³Enter the Diameter value 0.75 (Enter).TOMBSTONE PROJECT[Enter the center point]: Select the Fast Point icon.Enter the values :Press Enter.Select the Apply button.Enter the Diameter valueto remain in the same command.2.0 (Enter).[Enter the center point]: Select the Fast Point icon.Enter the values :Press Enter.Select the OK button. to exit the command.XformTranslateSelect the 2“ diameter circleSelect thiscircleSelect End Selection button.Change the parameters in the Translate dialog box as shown to the right.Make sure that Join is enable and Z is set to 0.25The preview of the geometry should look as shown bellow.Select the OK button to exit the Translate dialog box. Page 1 9 X³ TOMBSTONE PROJECTSTEP 3:CREATE THE OBROUND SHAPE IN THE RIGHT SIDE CONSTRUCTION PLANE.Select Planes in the Status Bar.Select Right side.Change the current construction Z depth to 4.75 by entering the value in the Status Bar as shown.CreateRectangular ShapesType the Width and the Height as shown in the following screenshot.Select the Obround as shown.Select thisradio buttonSelect the middle radio button as the anchor.Select thisradio button[Select position of base point]: Select the Fast Point icon.Move the Rectangular Shapes Options dialog box if necessary.Enter the values :Press Enter.Select the OK button to exit the rectangle dialog box.Page 1 10 [...]... selected view button Check Enable origin to set the new origin for the plane at the lower left corner based on the view coordinates Change the Work Offset # to 0 To set different work offset for each Tplane, Mastercam requires that you specify work offsets in a generic format Offsets are identified starting with the number zero and incremented by one for each successive offset For example, in Fanuc controls,... Incremental values are relative to the location of the chained geometry Clearance, Retract, and Feed plane are relative to the Top of stock Select the Depth cuts button to enter a maximum rough step that Mastercam uses to divide the total depth into equal steps and to set the finish pass Select the OK button to exit Depth cuts Page 1 28 X³ TOMBSTONE PROJECT Select the Roughing/Finishing parameters and . 2008Copyright © 1984 - 2008 In-House Solutions Inc. - All rights reserved.Software: Mastercam Mill X³Authors: Mariana LendelISBN: 97 8-1 -9 2656 6-1 4-6 NoticeIn-House Solutions. 1-8 0 0-5 2 9-5 517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X³ Training Tutorials – Indexing (Tombstone & Chuck)-