Centum CS300 r3 engineering course

179 55 0
  • Loading ...
1/179 trang
Tải xuống

Thông tin tài liệu

Ngày đăng: 18/10/2019, 19:35

1. PROJECT CREATION Project Creation2.1 PROCESS IO DEFINITION (PFCS) 2.1.1 Analog IO Definition 2.1.2 Digital IO Definition 2.2 PROCESS IO DEFINITION (LFCS) 2.2.1 Analog IO Definition 2.2.2 Digital IO Definition 2.3 PROCESS IO DEFINITION (KFCS) 2.3.1 Analog IO Definition 2.3.2 Digital IO Definition 2.4 PROCESS IO DEFINITION (FFCS_L) 2.4.1 Analog IO Definition 2.4.2 Digital IO Definition TRAINING CENTRE (SINGAPORE) STUDENT TRAINING WORKBOOK Name : Company : Course Period : Document No: CKEG_R3_Vnet/IP_WB Ed September 2007 Document No: CKEG_R3_Vnet/IP_WB Ed September 2007 COURSE : CS 1000 & CS 3000 ENGINEERING (Vnet/IP) NAME OF COURSE MATERIAL USED : CS 1000 & CS 3000 ENGINEERING (Vnet/IP) Edition Date September 2001 December 2004 March 2006 September 2007 This document is maintained by Revised Item Contents Revised Materials to Vnet/IP Revision : Wendy Kok Rev No.* R3.01 R3.04 R3.06 R3.07 Author Jessie Chong Jessie Chong Jessie Chong Ivan Choo Initial: Wendy Kok Date: September 2007 Note: Instruction Manual is updated/controlled by YHQ * - Denotes the release no of the software corresponding to the contents of this instruction manual The revised contents are valid until the next edition is issued TABLE OF CONTENTS TABLE OF CONTENTS PROJECT CREATION Project Creation 2.1 PROCESS I/O DEFINITION (PFCS) 2.1.1 Analog I/O Definition 2.1.2 Digital I/O Definition 11 2.2 PROCESS I/O DEFINITION (LFCS) 2.2.1 Analog I/O Definition 2.2.2 Digital I/O Definition 16 20 2.3 PROCESS I/O DEFINITION (KFCS) 2.3.1 Analog I/O Definition 2.3.2 Digital I/O Definition 25 32 2.4 PROCESS I/O DEFINITION (FFCS_L) 2.4.1 Analog I/O Definition 2.4.2 Digital I/O Definition 37 42 CREATION OF REGULATORY CONTROL FUNCTION Cascade Loop Operation 3.1 Function Block Creation 3.1.1 Control Drawing Builder Activation 3.12 Drawing and Editing of Control Drawing Window 3.2 User Defined Window Creation 3.2.1 Control Window Creation 3.2.2 Trend Window Creation 3.3 Confirmation of Operation with Test Function 3.3.1 Start-up of Test Function 3.3.2 Wiring Data Change 3.3.3 Wiring Operation Function 3.3.4 Confirmation of Operation by Operation and Monitoring Function 3.3.5 Control Drawing Window Display 48 48 49 62 62 65 68 68 70 73 74 77 MODIFICATION OF FUNCTION BLOCK 4.1 4.2 Open-Close Mark Change of Range YOKOGAWA SINGAPORE TRAINING CENTRE 78 80 Page of CKEG_R3_Vnet/IP_WB Ed September 2007 TABLE OF CONTENTS CASCADE CONTROL SIGNAL DISTRIBUTION BLOCK 5.1 5.2 Control Action of Cascade Signal Distribution Block (FOUT) 84 5.1.1 Cascade Control Signal Distribution Block 84 Operation Procedure 86 CREATION OF SEQUENCE TABLE 6.1 6.2 6.3 6.4 6.5 Common Switch Definition Control Drawing Creation 6.2.1 Control Drawing Builder Activation 6.2.2 Function Block Creation 6.2.3 Timer Definition 6.2.4 Sequence Table Definition Function Block Detail Definition 6.3.1 Timer Definition 6.3.2 Sequence Table Definition Control Window Definition 6.4.1 Graphic Builder Activation Confirming Operation with Test Function 6.5.1 Activating Test Function 6.5.2 Confirming Operation with Operation and Monitoring Function 6.5.3 Exiting Test Function 88 90 90 91 93 94 95 95 96 102 102 106 106 107 109 7.1 CREATION OF GENERAL PURPOSE CALCULATION BLOCK1 7.1.1 Control Drawing Builder Creation 7.1.1.1 Control Drawing Builder Activation 7.1.1.2 Function Block Creation 7.1.1.3 Operation Test 7.2 CREATION OF GENERAL PURPOSE CALCULATION BLOCK 120 CREATION OF LOGIC FUNCTION 8.1 8.2 8.3 8.4 8.5 111 111 112 119 Common Switch Definition Control Drawing Creation Control Window Creation Confirming Operation with Test Function Behaviour of Logic Chart Internal Timer 121 122 126 127 128 CREATION OF GRAPHICS 9.1 9.2 9.3 Creation of Level Control Loop Drawing and Editing the Graphic Window Inspecting the Graphic Window YOKOGAWA SINGAPORE TRAINING CENTRE 130 131 163 Page of CKEG_R3_Vnet/IP_WB Ed September 2007 PROJECT CREATION PROJECT CREATION Create a new project using System View AIM : To create a user-defined project ENGPJT and define field control station (FCS0101) and human interface station (HIS0164)*1 To create a user-defined project ENGPJT and define field control station (FCS0101) and human interface station (HIS0124)*1 To create a user-defined project VNETIP and define field control station (FCS0101) and human interface station (HIS0164)*1 *1: HIS number subject to change if VF701 card is installed Procedure: Activate the System View by selecting [Start] [All Programs] [YOKOGAWA CENTUM] [System View] or by selecting [Activate System View] in the [Window Call Menu] YOKOGAWA SINGAPORE TRAINING CENTRE Page CKEG_R3_Vnet/IP_WB Ed September 2007 PROJECT CREATION Select [File] [Create New] [Project] The [Outline] window appears Enter the data in the User, Organization and Project information columns Click on [OK] button YOKOGAWA SINGAPORE TRAINING CENTRE Page CKEG_R3_Vnet/IP_WB Ed September 2007 PROJECT CREATION The [Create New Project] window appears Enter the data as follows : Click on [OK] button [Create New FCS] window appears Set as follows : Station Type : PFCD-H Duplexed Field Control Station (Compact Type) AFS20D Duplexed Field Control Unit (for RIO, with Cabinet) OR AFS10D Duplexed Field Control Unit (for RIO, Rack Mountable) AFS40D Duplexed Field Control Unit (for FIO, with Cabinet) AFV10D Duplexed Field Control Unit (for VnetIP, for FIO, 19” Rack Mountable) Database Type : General - Purpose Domain Number :1 Station Number :1 Component / Number : Leave it blank Station Comment : Leave it blank Alias of Station : Leave it blank Station Status Display : Leave it blank Upper Equipment Name : Leave it blank YOKOGAWA SINGAPORE TRAINING CENTRE Page CKEG_R3_Vnet/IP_WB Ed September 2007 PROJECT CREATION Click on [OK] button YOKOGAWA SINGAPORE TRAINING CENTRE Page CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS 17 When the next tool is selected, the object gets deselected The graphic image created up to this point is shown below: 18 Change the grid for easy drawing Select the [Zoom Out] from the toolbar A 200% grid is displayed 19 Select the [Circle] from the toolbar 20 Drag the cursor from point a to point b A circle is displayed 21 Select [Line] from the [Format] menu The property setting menu dialog box to specify the [Circle] of the object is displayed 22 Set the items on the Line tab of the property setting menu dialog box as shown below • Line Style: Solid line • Line Thickness: dot • Line Color: Green 23 Click the [Apply] button Check that the setting contents are displayed and click the [OK] button The property setting menu dialog box closes YOKOGAWA SINGAPORE TRAINING CENTRE Page 152 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS 24 Select the [Straight Line] tool button from the toolbar 25 Drag the cursor from point a to point b A straight line is displayed 26 Select [Line] from the [Format] menu of the menu bar The property setting menu dialog box to specify the [Straight Line] of the object is displayed 27 Set the items on the Line tab of the property setting menu dialog box as shown below • Line Style: Solid line • Line Thickness: dot • Line Color: Green 28 Click the [Apply] button Check that the setting contents are displayed and click the [OK] button The property setting menu dialog box closes 29 When the next tool is selected, the selection of the object is canceled The graphic completed up to this point is shown below: YOKOGAWA SINGAPORE TRAINING CENTRE Page 153 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Creating the Tag Name and Level Unit: Select the [Text] from the toolbar Click point a The drawing area of the text appears Enter the text [LIC100], and click an arbitrary point on the screen to enter the next text Click the point b and enter the text [M] LIC100 Select the [Select Mode] button from the toolbar Select the text [LIC100] Select [Text] from the [Format] menu The property setting menu dialog box to specify the [Text] of the object is displayed Set the items on the Text tab of the property setting menu dialog box as shown below • Font: Arial • Size: 16 point • Text Color: Green • Background Color: Black Click the [Apply] button Check that the setting contents are reflected 10 Select the text [M] The setting items of the property setting menu dialog box are redirected to the text [M] 11 Set each item in the same way as Click the [Apply] button YOKOGAWA SINGAPORE TRAINING CENTRE Page 154 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS 12 Clicking the [OK] button closes and deselects the text menu The graphic image created up to this point is shown below: Displaying Process Data: Select the [Process Data-Character] from the toolbar Click point a The characters [RRRRRRR] are displayed LIC100 Select the [Text] from the [Format] menu The property setting menu dialog box to specify the [Process Data-Character] of the object is displayed YOKOGAWA SINGAPORE TRAINING CENTRE Page 155 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Set the items on the Text tab of the property setting menu dialog box • Font: Arial • Size: 16 point • Text Color: Cyan • Background Color: Black Select the [Process Data-Character] tab of the property setting menu dialog box • Type: Numerical Value • Number of Digits for Integer: • Number of Digits After the Decimal Point: • Data Type: Process Data • Display Data: LIC100.PV Click the [Apply] button Check that the setting contents are displayed and click the [OK] button The property setting menu dialog box closes YOKOGAWA SINGAPORE TRAINING CENTRE Page 156 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS When the next tool is selected, the text menu closes and becomes deselected The graphic image created up to this point is shown below: Setting the Touch Target: Select [Touch Target] from the toolbar Drag the cursor from point a to b LIC100 RRRR.RR M Select the [General] from the [Format] menu of the menu bar The property setting menu dialog box to specify the [Touch Target] of the object is displayed YOKOGAWA SINGAPORE TRAINING CENTRE Page 157 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Set the items on the Function tab of the property setting menu dialog box: • Function Type: Call Window • Window Name: Tuning • Parameter: LIC100 • Specify Window Size: • Window Size: Medium Size • Specify Window Display Position: • Specify Coordinates: • Display Position X: 500 • Display Position Y: 300 Click the [Apply] button and the [OK] button The property setting menu dialog box closes YOKOGAWA SINGAPORE TRAINING CENTRE Page 158 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS The object becomes deselected when the [Select Mode] tool is selected The graphic image created up to this point is shown below: YOKOGAWA SINGAPORE TRAINING CENTRE Page 159 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Registering Parts: The created objects such as shut-off valves and detectors can be saved as parts files There are system files and user files in the parts files Parts can be stored as user files from the [Insert] menu in the menu bar of Graphic Builder The Graphic Select [Parts] Parts window will display Parts list display area Parts image display area Parts explanation display area Select the [User] option for parts file type on Parts Window Click on the [Display Always] window to the Parts window button Drag the created shut-off valve in the Graphic YOKOGAWA SINGAPORE TRAINING CENTRE Page 160 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS The part is displayed when dropped in the Parts Image Display Area To save the part, select [Save As] from the [File] menu The [Save As] dialog box is displayed Save in “Desktop” with “Shut Off Valve” as the file name Click the [Save] button YOKOGAWA SINGAPORE TRAINING CENTRE Page 161 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Setting Parts Name and Comment on the Parts: Select [Properties] from the [Edit] menu in the Parts window The Change Part Properties dialog box is displayed Set the parts name as “Valve 1” and comment for the parts as “GR0001” in the Change Part Properties dialog box Click the [OK] button, and the data that has been set will be displayed in the parts list display area and the parts explanation display area of the Parts window Referencing Parts: The parts that have been registered (shut-off valve, detector, etc.) can be reused in a different Graphic window as needed Select [Parts] from the [Insert] menu in the menu bar The Parts window is displayed Select [User] of the [Type of Parts File] items in the Parts window Select [Open] from the [File] menu The Open dialog box is displayed Select “Shut Off Valve” form the “Desktop” in the Open dialog box Click the [Open] button, then the specified parts file appears in the Parts window Select the desired part from the parts list in the Parts window The specified part appears in the parts image display area YOKOGAWA SINGAPORE TRAINING CENTRE Page 162 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Drag the part in the parts image display area to a suitable location the graphic builder window 9.3 Inspecting the Graphic Window An individual test of the Graphic window is performed during editing Enter data to the process data LIC100 and check the operation of data character display Double click on the “Process Data – Bar” and the property setting menu dialog box appears YOKOGAWA SINGAPORE TRAINING CENTRE Page 163 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Check the check box [Set Data During Debugging] in the General tab of the property setting menu dialog box Click on [OK] Repeat the same procedure for the “Shut Off Valve” and “Process Data – Character” Select the [Debug] from the [Tools] menu of the menu bar The debug dialog box is displayed Select [Process Data – Character] in the type column and set the following items in the debug dialog box: • Data Kind: Numerical Value • Data Value: 50 YOKOGAWA SINGAPORE TRAINING CENTRE Page 164 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Click the [Update Data] button Check that the dummy data appear in the data character display and the change in the data rectangle bar display of the debug window Select [Modify] in the type column and set the following items in the debug dialog box • Data Kind: Numerical Value • Data Value: YOKOGAWA SINGAPORE TRAINING CENTRE Page 165 CKEG_R3_Vnet/IP_WB Ed September 2007 CREATION OF GRAPHICS Click the [Update Data] button Check that “Shut Off Valve” changes to “Magenta” in the debug window When the checking result is NG, make sure that the primitive attribute setting is correct 10 When it is necessary, correct it and click the [ReRead] button of the Debug dialog box 11 Click the [Exit Debug] button, and the dialog box closes and the check ends YOKOGAWA SINGAPORE TRAINING CENTRE Page 166 CKEG_R3_Vnet/IP_WB Ed September 2007 ...Document No: CKEG _R3_ Vnet/IP_WB Ed September 2007 COURSE : CS 1000 & CS 3000 ENGINEERING (Vnet/IP) NAME OF COURSE MATERIAL USED : CS 1000 & CS 3000 ENGINEERING (Vnet/IP) Edition Date... maintained by Revised Item Contents Revised Materials to Vnet/IP Revision : Wendy Kok Rev No.* R3. 01 R3. 04 R3. 06 R3. 07 Author Jessie Chong Jessie Chong Jessie Chong Ivan Choo Initial: Wendy Kok Date:... [Start] [All Programs] [YOKOGAWA CENTUM] [System View] or by selecting [Activate System View] in the [Window Call Menu] YOKOGAWA SINGAPORE TRAINING CENTRE Page CKEG _R3_ Vnet/IP_WB Ed September 2007
- Xem thêm -

Xem thêm: Centum CS300 r3 engineering course, Centum CS300 r3 engineering course, 1 PROCESS I/O DEFINITION - PFCS, 2 PROCESS I/O DEFINITION - LFCS, 3 PROCESS I/O DEFINITION - KFCS, 4 PROCESS I/O DEFINITION – FFCS_L

Gợi ý tài liệu liên quan cho bạn