THIẾT KẾ CHẾ TẠO KHUÔN MẪU ĐỦ 25 BÀI_SPKT_23-EN

21 388 0
THIẾT KẾ CHẾ TẠO KHUÔN MẪU ĐỦ 25 BÀI_SPKT_23-EN

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

MOULD HEART BE PROCESSED TILT, 3D GVHD: TRẦN MINH THẾ UYÊN SVTH : Nguyễn Hoàng Linh MSSV : 12144060 A few examples of products available tilted cavity I METHOD OF CHICKEN EMBRYO TILT The jig according marker – Intersection incline is scribing – Pallet to vice – Using tracer to review for parallel scribing – Milling Milling like parallel planes with knives or knife cylinder head surface 2 Tilt embryos by wedging angle • When the pallet onto a vise, not use parallel that used wedge wedge angle, wedge angle equal to the angle of the details • After fixing, milling inclined plane as the plane parallel milling α α Holder according to angle size, baseline Face machining Apply alongside vice Pressed surface details By vice Multimeters By tilting universal fixtures II MILLING INCLINE MACHETER BY CORNER  When the inclined plane with small width, using machetes corner III MILLING BY USING INCLINED PLANE TILTED HEAD TOOL  Formed milling head  The position of the swivel milling head  Milling head can be rotated on a plane to ± 90 ° angle of oxygen  Some special types can be rotated in the plane yoz  Normally only be rotated ± 45 ° Milling the inclined plane with the knife cylinder Tilt angle milling head milling incline angle α α Milling the inclined plane with the first surface of the knife o When using a knife face head, milling head tilt angle β=90 -α Sn β Sn α=75 O IV MILLING SLANTED SURFACE WITH ALMIGHTY SELL ROTATE Milling with hinged swivel table IV MILLING SLANTED SURFACE WITH ALMIGHTY SELL ROTATE Drilling oblique V ORDER OF THE MILLING INCLINED PLANE embryos up jig jig Select and hinged machetes Adjust the cut Select the dimension machined Review knife, adjust Cutting depth Where: t = h.cos h t α VI CHECK INCLINE PLANE Check with nursing protractors • • • • Protractors measured in common - There are no high precision Measured with a multimeter protractors - Yes measurement accuracy to ' o α=45 Use protractors - Read the value of the opacity - Plus part minute (') outlines coincide on travelers spend (like on caliper) VI MOULD PROCESSING 3D) Zigzac   Zigzag method usually have options: Run knife under road (two way) Run knife in a street (one way) 2 Tooth comb After each run the knife, knife receded from the face of outsourcing a distance and then ran the initial starting point to cut the next step Run knife method is used when processing crystal surfaces forming steep, narrow grooves VII GIA CÔNG KHUÔN 3D Xoắn ốc Phương pháp chạy dao theo kiểu Spiral: dụng cụ cắt bắt đầu chuyển động từ tâm điểm bắt đầu khu vực cần gia công, tiếp tục gia công khu vực lại theo đường xoắn ốc Thank! [...]... point to cut the next step Run knife method is used when processing crystal surfaces forming steep, narrow grooves VII GIA CÔNG KHUÔN 3D 3 Xoắn ốc Phương pháp chạy dao theo kiểu Spiral: dụng cụ cắt bắt đầu chuyển động từ tâm hoặc điểm bắt đầu của khu vực cần gia công, và tiếp tục gia công khi các khu vực còn lại theo đường xoắn ốc Thank!

Ngày đăng: 20/09/2016, 13:13

Từ khóa liên quan

Mục lục

  • Slide 1

  • Slide 2

  • I. METHOD OF CHICKEN EMBRYO TILT

  • Slide 4

  • Slide 5

  • Slide 6

  • Slide 7

  • II. MILLING INCLINE MACHETER BY CORNER

  • III. MILLING BY USING INCLINED PLANE TILTED HEAD TOOL

  • Slide 10

  • Slide 11

  • Slide 12

  • IV. MILLING SLANTED SURFACE WITH ALMIGHTY SELL ROTATE

  • IV. MILLING SLANTED SURFACE WITH ALMIGHTY SELL ROTATE

  • V. ORDER OF THE MILLING INCLINED PLANE

  • VI. CHECK INCLINE PLANE

  • Slide 17

  • VI. MOULD PROCESSING 3D)

  • Slide 19

  • VII. GIA CÔNG KHUÔN 3D

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan