Removal Joint Using the (-) driver, remove the joint 2.Molding assembly Remove the molding assembly using a(-) screwdriver Remove the molding 4.Using the piano wire, cut the adhesive between side window glass and body Using a cutter knife scrape the old sealant smoothly to a thickness of about mm on the bonding surface around the entire windshield flange 5.Remove the side window glass Half fixed, Half slide type Joint Remove the joint using a flat-tipped(-) screwdriver 2.Molding assembly Remove the molding assembly using a flat-tipped(-) screwdriver Remove the molding 4.Using a cutter knife, or cutting machine cut the adhesive between side window assembly and body Scrape the old sealant smoothly to a thickness of about mm on the bonding surface 5.Remove the side window assembly 6 Remove the side window from the side window assembly Installation Clean carefully remaining adhesive on the body side pillar Repair damaged coating and rust, if any 2.Clean the whole edge (width: 20mm) of the glass and the glass matching area with the unleaded gasoline and dry up at least minutes Glue the window dam around the body member and window pillar 4.Install the clip of side window lower part 5.Install the molding of side window front part Apply the seek cleaner on the glass with width 20 mm and set 5-10 minutes after Upon applying cleaner, not touch or attach oily object 7.Apply the adhesive of the window dam • Glue the adhesive with height 12 mm and width mm of triangle • In applying adhesive, be careful not to make incontinuous or excessive bead at beginning, at finish ing and at a corner • It is a quick hardening adhesive Proceed the work one by one • A working shift shall be not longer than minutes from be ginning to apply the adhesive to matching and fitting the glass • The adhesive is of urethane series, that does not go with silicone sealer The adhesive shall be used at least 1mm away from silicone sealer and good ventilation shall be provided, as well 8.Lift up the side window glass using suction cups not to contaminate the cleaner applied surface on the side window 9.Caring not to remove adhesive applied at the bottom by the glass, put the side window bottom on the clip 10 Watching the right-left gaps of the glass install the glass pressing inside from the upper part 11 Press the upper part of the glass with the clip 12.Remove the surplus adhesive quickly before hardened 13 Molding (1)Apply the adhesive (SEEKER FLEX 250PC) to the stud position (2)Install the lower flange of molding to the window glass (3)Fill the adhesive in the stud 14 Molding Assembly Install the molding assembly to the upper and lower window glass Install the joint to the molding assembly connection and end cap to the end • Heed to top or bottom of molding assembly Install the knar row section of molding assembly to the window glass side • For installation of the clip, draw the one side the molding assembly Do not tap it expressively 15.Clean the adhesive or pollutants with gasoline on the window glass and molding Half fixed, Half slide type Remove or clean the adhesive of body of pillar If the paintwork is damaged, repair the damaged area with touch-up paint or antirust solvent 2.Clean the whole edge of the side window assembly and the window assembly adhesive area using the unleaded gasoline and leave it at least minutes to dry • Apply the SEEK cleaner in the whole round when installing the window assembly into the adhesive area • Caution to be free from foreign material (Hand mark Oily gloves) • If not confirming the former procedure, it may cause the leak water and the grease and the window assembly can be slipped out Attach the window dam around the body member and window pillar as shown illustration 4.Install the lower edge clip of the side window 5.Install the molding to the front side window assembly Matching the glass, apply appropriate quantity of gasoline for better slip of rubber Apply the SEEK cleaner to side window assembly and window assembly contact surface and set 5-10 minutes after Upon applying cleaner, not touch or attach oily abject 7.Apply the adhesive (SEEKER FLEX 250PC) along window dam • Glue the adhesive with height 12mm, width 8mm of triangle • In applying adhesive, be careful not to make incontinuous or excessive bead at beginning, at finishing and at a corner • It is a quick hardening adhesive Proceed the work one by one A working shift shall be not longer than minlutes from beginning to apply the adhesive to matching and fitting the glass • The adhesive is of urethane series, that does not go with silicone sealer.The adhesive be used at least mm away from silicone and good ventilation shall be provided, as well 8.Using a glass holler, lift up the side window glass and heed not to contamination of the side window assembly of the cleaner surface 9.Install the side window assembly on the clip 10 Heeding the gaps of both sides of window assemblies, push the upper glass to the inside 11 Fix the clip of chassis upper part 12.Quickly scrape or wipe excessive adhesive off the putty knife or gauze 13 Remove the masking tape to make drain hole 14 Molding (1)Apply the adhesive (SIKA) to the stud position (2)Match the lower flange of the molding with the window assembly (3)Fill the adhesive in the stud 15.Molding Assembly Install the molding assembly to the upper and lower window glass Install the joint to the molding assembly connection and end cap to the end • Heed to top or bottom of molding assembly Install the narrow section of molding assembly to the window glass side • For installation of the clip, draw the one side the molding assembly 16 Clean the adhesive or pollutants with the gasoline on the window glass and molding Side Window(Fixed Window) Cut the weather strip glass fitting area using a cutter knife and put off the glass outward from the vehicle 1 Clean the glass cut area with the unleaded gasoline and leave it at least minutes to dry 2.Carefully clean off the remaining sealing material on the window frame Install the weather strip on the glass 4.Install the glass on the window frame and carefully apply sealing material (Packing seal 960) on the matching surface preventing water leak 5.Clean the sealing material and dirt around the glass weather strip Side Window(Sliding Window Area) Move the window frame(built-in) to the center and release the attaching type rail mounting screw(A) 2.Pull off the window frame(built-in) to the left together with the attaching type rail Cut the fitting surface between weather strip(Rubber) and the glass 4.Disassemble the window frame and remove the side window glass the weather strip(Rubber) Checking Check the run channel for damage, and replace it, if required Cleanse the glass cut area with unleaded gasoline and leave it to dry at least minutes 2.Remove sealing material attached to the window frame(built-in) Apply sealing material (Packing seal 960) at the fitting area between the weather strip(Rubber) and the glass and insert the side window 4.Assemble the window frame(built-in) 5.Clean sealing material and dirt around the glass and the weather strip using unleaded gasoline Set the attaching type rail and fit onto the window frame 7.Fix the attaching type rail, tightening the mounting screw(A) Sealant and Adhesive for Glass, and Sealant, Adhesive and Parts for Maintenance NO Part Name Remarks Cemedine 560 Front window Prior Sunstar 435-40(Made by Sunstar) Glass surface Prior Sunstar 435-95(Made by Sunstar) Painted surface Better Seal 551(Made by Sunstar) Front window, driver side window Primer N-200 Front window Knit Sealant 687 Rear widow Front window, driver side window Cemedine CS3061-6ALR Rear widow Knit After Sealer 681 Driver side window Penking Seal 960(Sunstar 211) Driver side window, side window 10 Seeker flex 250PC Side window 11 Thicker Cleaner(No.1) Side window 12 Thicker Primer(VP 209) Painted surface 13 Thicker Black Primer Glass (both surfaces) NO Part Name Remarks Unleaded gasoline or toluene Cleaning Thin brush, pencil Primer coating Putty Knife Finishing sealed area Sealer gun Sealing device Vinyl tape, masking tape Masking for primer coated area Cutter knife Cutting sealant Base Preparing maintenance equipments Anti-corrosive coating, touch-up paint Repair Glass holder Supporting window glass 10 Piano wire 0-6 Cutting sealant 11 (-) screwdrive Removing molding 12 Other maintenance parts Sponge rubber, weather strip, butyl rubber type, clip, spacer, end cap mole holder, etc Caution for the use of Seeker flex 250PC The followings are to provide general warnings for the use of adhesive and cleaner Removal and installation procedures for the window are provided at the corresponding chapter Removing the window and the window assembly, cut the adhesive to leave approx 1mm thick layer using piano wire or a cutting machine 2.For removing the coating, apply primer VP 209 In order to remove ceramic film on glass, apply black primer and then repair it 3 Body side and window matching area shall be cleaned with the unleaded gasoline and left for drying at least minutes 4.Upon applying Thicker Cleaner No.1, wait 5-10 minutes for drying Upon applying cleaner, not touch or attach oily object 5.Apply the sealant(Seekerflex 250PC) according to following cautions • Glue the adhesive with height 12mm and width 8mm of triangle • In applying adhesive, be careful not to make incontinuous or excessive bead at beginning, at finishing and at a corner • It is a quick hardening adhesive Proceed the work one by one A working shift shall be not longer than minutes from beginning to apply the adhesive to matching and fitting the glass • The adhesive is of urethane series, that does not go with silicone sealer The adhesive shall be used at least 1mm away from silicone sealer and good ventilation shall be provided, as well Lift up the side window using suction cups not to contaminate the cleaner applied surface If the cleaner applied surface is touched or oily material is stuck on the surface, apply it once again 7.Remove the surplus adhesive quickly before hardened and clean with unleaded gasoline [...]... Front window 2 Prior Sunstar 435-40(Made by Sunstar) Glass surface 3 Prior Sunstar 435-95(Made by Sunstar) Painted surface 4 Better Seal 551(Made by Sunstar) Front window, driver side window 5 Primer N-200 Front window 6 Knit Sealant 687 Rear widow Front window, driver side window 7 Cemedine CS3061-6ALR Rear widow 8 Knit After Sealer 681 Driver side window 9 Penking Seal 960(Sunstar 211) Driver side window, ... and lower window glass Install the joint to the molding assembly connection and end cap to the end • Heed to top or bottom of molding assembly Install the narrow section of molding assembly to the window glass side • For installation of the clip, draw the one side the molding assembly 16 Clean the adhesive or pollutants with the gasoline on the window glass and molding Side Window( Fixed Window) Cut... clean off the remaining sealing material on the window frame 3 Install the weather strip on the glass 4.Install the glass on the window frame and carefully apply sealing material (Packing seal 960) on the matching surface preventing water leak 5.Clean the sealing material and dirt around the glass weather strip Side Window( Sliding Window Area) 1 Move the window frame(built-in) to the center and release... the side window assembly on the clip 10 Heeding the gaps of both sides of window assemblies, push the upper glass to the inside 11 Fix the clip of chassis upper part 12.Quickly scrape or wipe excessive adhesive off the putty knife or gauze 13 Remove the masking tape to make drain hole 14 Molding (1)Apply the adhesive (SIKA) to the stud position (2)Match the lower flange of the molding with the window. .. widow Front window, driver side window 7 Cemedine CS3061-6ALR Rear widow 8 Knit After Sealer 681 Driver side window 9 Penking Seal 960(Sunstar 211) Driver side window, side window 10 Seeker flex 250PC Side window 11 Thicker Cleaner(No.1) Side window 12 Thicker Primer(VP 209) Painted surface 13 Thicker Black Primer Glass (both surfaces) NO Part Name Remarks 1 Unleaded gasoline or toluene Cleaning 2 Thin... sealing material attached to the window frame(built-in) 3 Apply sealing material (Packing seal 960) at the fitting area between the weather strip(Rubber) and the glass and insert the side window 4.Assemble the window frame(built-in) 5.Clean sealing material and dirt around the glass and the weather strip using unleaded gasoline 6 Set the attaching type rail and fit onto the window frame 7.Fix the attaching... window frame(built-in) to the center and release the attaching type rail mounting screw(A) 2.Pull off the window frame(built-in) to the left together with the attaching type rail 3 Cut the fitting surface between weather strip(Rubber) and the glass 4.Disassemble the window frame and remove the side window glass the weather strip(Rubber) Checking Check the run channel for damage, and replace it, if required... the window are provided at the corresponding chapter 1 Removing the window and the window assembly, cut the adhesive to leave approx 1mm thick layer using piano wire or a cutting machine 2.For removing the coating, apply primer VP 209 In order to remove ceramic film on glass, apply black primer and then repair it 3 Body side and window matching area shall be cleaned with the unleaded gasoline and... holder Supporting window glass 10 Piano wire 0-6 Cutting sealant 11 (-) screwdrive Removing molding 12 Other maintenance parts Sponge rubber, weather strip, butyl rubber type, clip, spacer, end cap mole holder, etc Caution for the use of Seeker flex 250PC The followings are to provide general warnings for the use of adhesive and cleaner Removal and installation procedures for the window are provided... adhesive is of urethane series, that does not go with silicone sealer The adhesive shall be used at least 1mm away from silicone sealer and good ventilation shall be provided, as well 6 Lift up the side window using suction cups not to contaminate the cleaner applied surface If the cleaner applied surface is touched or oily material is stuck on the surface, apply it once again 7.Remove the surplus