Đang tải... (xem toàn văn)
tai lieu van hanh cua bien tan ALSTOM
Operating Manual ALSPA MD2000 22 kVA . 275 kVA Safety and Operating Instructions for F req uency C onv erters according to Low Voltage Directive 73/23/EEC 1. General During op eration, f req uency converters can h ave live, rotating or m oving p arts and th eir surf aces m ay b ecom e h ot, dep ending on th e p rotection class involved. T h ere is a risk of severe p h y sical inj ury or m aterial dam age if any of th e covers are rem oved or th e unit is installed, used or op erated incorrectly . F urth er details are given in th e docum entation. A ll sy stem design, transp ort, installation, com m issioning and m aintenance work m ust b e carried out b y q ualif ied sp ecialist p ersonnel ( according to I EC 6 0 36 4 , CEN ELEC H D 38 4 or DI N VDE 0 1 0 0 and I EC 6 0 6 6 4 or DI N VDE 0 1 1 0 and national saf ety regulations) . Q ualif ied sp ecialist p ersonnel in th e sense of th ese saf ety instructions are p ersons wh o are ex p erienced in th e sy stem design, installation, erection, com m issioning and op eration of th e p roduct and h ave th e q ualif ications req uired f or such work . 2 . C o rrec t u s e Converters are intended f or installation in electrical p lant or m ach inery . W h en installed in m ach ines th e converter m ay not b e com m issioned ( i. e. op eration of th e converter m ay not b e started) until it is evident th at th e m ach ine com p lies with EC directive 9 8 /37/EC ( M ach ine Directive) ( f orm erly 8 9 /39 2/EEC) . A lso EN 6 0 20 4 m ust b e ob served. Com m issioning ( i. e. op eration) is only p erm itted in com p liance with th e EM C directive ( 8 9 /336 /EEC) . O ur converters satisf y th e req uirem ents of low voltage directive 73/23/EEC. T h e standards of th e series EN 5 0 1 78 / DI N VDE 0 1 6 0 in conj unction with EN 6 0 4 39 - 1 / VDE 0 6 6 0 P art 5 0 0 and EN 6 0 1 4 6 / VDE 0 5 5 8 are ap p licab le to drive converters. T h e tech nical data and th e connection conditions are sh own on th e rating p late and in th e docum entation. T h ey m ust b e ob served. 3 . T rans p o rt and s t o rag e T h e instructions f or transp ort, storage and correct h andling m ust b e ob served. Clim atic conditions are to b e m aintained according to EN 5 0 1 78 . 4 . I ns t allat i o n T h e installation and cooling m ust b e in accordance with th e relevant docum entation. A ll converters m ust b e p rotected against undue m ech anical sh ock s or stress. I n p articular no com p onents m ay b e b ent and/or no insulation sp acing m ay b e altered during transp ort and h andling. Do not touch electronic com p onents or contacts. Converters contain com p onents suscep tib le to electrostatic disch arge ( ES D) wh ich are easily dam aged b y static electricity or incorrect h andling. Do not dam age m ech anically or destroy electrical com p onents ( h ealth h az ard p ossib le) . 5 . E lec t ri c al c o nnec t i o n T h e ap p rop riate national saf ety regulations ( e. g. B G V A 2) m ust b e ob served wh en work ing on converters wh ich are connected to th e electricity sup p ly . T h e electrical installation m ust b e ex ecuted in accordance with th e relevant regulations ( e. g. cab le cross- sections, f uses, earth ing) . A dditional instructions are given in th e docum entation. I nstructions on EM C com p liant installation, such as screening, earth ing, f ilters and cab le routing, are also given in th e converters docum entation. T h ese also ap p ly to converters b earing th e CE m ark . Com p liance with th e lim its sp ecif ied in EM C legislation is th e resp onsib ility of th e p lant or th e m ach inery m anuf acturer. 6 . O p erat i o n I f necessary , p lant or m ach inery in wh ich converters are f itted m ust b e eq uip p ed with additional m onitoring and saf ety f acilities in accordance with th e relevant regulations, e. g. th e law on tech nical eq uip m ent, th e ap p rop riate saf ety regulations etc. Do not touch any p arts of th e eq uip m ent wh ich m ay b e live or any p ower connections even af ter th e converter h as b een isolated f rom th e electricity sup p ly , as cap acitors m ay rem ain ch arged. F ollow th e instructions given on warning lab els. A ll covers and doors m ust b e k ep t closed during op eration. 7 . S erv i c e and m ai nt enanc e A ll instructions given in th e docum entation m ust b e ob served. K E E P T H E S E S A F E T Y I N S T R U C T I O N S I N A S A F E P L A C E Correction to Operating Manual A L S P A MD 2 0 0 0 / 0 2 9 . 1 4 6 7 4 8 A E 0 1 Correction to Operating Manual ALSPA MD2000 22 k V A . . . 27 5 k V A Ord er N o. 0 2 9 . 1 4 6 7 4 8 !!! The mains chokes are not included in the ALSPA MD2000 scope of supply!!! Page 6 2.2 Series of types A L SP A M D 20 0 0 for 3 - ph a se A C c on n ec tion A L S PA M D 2 0 0 0 2 2 . 2 7 5 k V A , 3 A C 3 8 0 . 4 8 0 V Pr o c es s o r - c o n t r o l l ed p u l s e i n v er t er w i t h f i el d - o r i en t at ed c o n t r o l c o n c ep t f o r c o n t i n u o u s l o w - l o s s s p eed ad j u s t m en t o f s t an d ar d A C m o t o r s . . . 1 ) R at ed c u r r en t w i t h o v er l o ad c ap ac i t y 1 .2 x r at ed c u r r en t 2 ) B as i c l o ad c u r r en t w i t h o v er l o ad c ap ac i t y 1 .5 x b as i c l o ad c u r r en t 3 ) M ax . c u r r en t f o r m ax . 60 s o v er l o ad , c y c l e t i m e 60 0 s 4 ) M ai n s c o m m u t at i o n c h o k e n ot i n c l u d ed i n s c o p e o f s u p p l y . N o t i n s t al l ed i n t h e A L S PA M D 2 0 0 0 . S u p p l i ed l o o s e f o r i n s t al l at i o n o u t s i d e t h e u n i t . 5 ) T h e d et ai l s f o r t h e m ai n s c u r r en t w i t h t h e s t an d ar d m ai n s c h o k e ar e b as ed o n a m ai n s s h o r t c i r c u i t c ap ac i t y i n r el at i o n t o t h e i n v er t er p o w er o f 1 0 0 : 1 at u n i t o u t p u t c u r r en t = r at ed c u r r en t . . S c o p e o f s u p p l y : B u i l d - i n u n i t , I P2 0 , i n c l u d i n g m ai n s c o m m u t at i o n c h o k e s u p p l i ed l o o s e Page 2 2 2.4 .1 .2 M a in s c h ok es ( 3 - ph a se c h ok es) I f t h e A L S PA M D 2 0 0 0 i s c o n n ec t ed t o a 3 A C m ai n s s u p p l y a m ai n s c h o k e i s r eq u i r ed i n t h e s u p p l y c ab l e t o r ed u c e t h e h ar m o n i c s an d l i m i t c o m m u t at i o n f ai l u r es . T h e m ai n s c h o k es f o r t h e r el ev an t A L S PA M D 2 0 0 0 t y p es ar e l i s t ed i n t h e t ab l e b el o w . M ai n s c h o k es ar e n ot i n c l u d ed i n t h e A L S PA M D 2 0 0 0 s c o p e o f s u p p l y f o r 3 A C m ai n s c o n n ec t i o n . T h ey ar e s u p p l i ed l o o s e w i t h t h e A L S PA M D 2 0 0 0 an d ar e i n s t al l ed o u t s i d e t h e A L S PA M D 2 0 0 0 i n t h e c u b i c l e. . . Page 1 7 5 5 .3 M a in s a n d m otor c on n ec tion Pl eas e r ef er t o t h e o p er at i n g m an u al " S o f t w ar e V 3 .0 " R ef . N o . 0 2 9 .2 0 8 8 8 9 f o r a c o m p r eh en s i v e d es c r i p t i o n o f p ar am et er s an d d i s p l ay s . . . T h e s em i c o n d u c t o r f u s es an d m ai n s c h o k es t o b e u s ed ar e l i s t ed i n s ec t i o n s 2 .4 .1 .1 an d 2 .4 .1 .2 . T h e m ai n s c h o k es ar e n ot i n c l u d ed i n t h e A L S PA M D 2 0 0 0 s c o p e o f s u p p l y an d ar e s u p p l i ed l o o s e. T h e m ai n s c o n t ac t o r , m ai n s f i l t er , p o w er d u m p an d m o t o r d u / d t f i l t er s ar e o p t i o n s an d ar e o n l y r eq u i r ed i f n ec es s ar y f o r t h e c o n n ec t i o n . . . Contents ALSPA MD2000 1 Brief description 1 1.1 General .1 1.2 Basic operation .2 1.3 Main features .3 2 Technical Data .5 2.1 Key to types, rating plate 5 2.2 Series of types .6 2.2.1 Technical data at rated current .8 2.2.2 Technical data at basic load current .9 2.2.3 Power loss and cooling air volume 10 2.3 System data 11 2.3.1 Standards, operating conditions and certificates .16 2.3.1.1 Standards applicable 16 2.3.1.2 Certificate 17 2.3.1.3 CE Certificate 17 2.3.2 CE mark 18 2.4 Supply components 20 2.4.1 Components for 3AC supply .20 2.4.1.1 Fuses for 3AC mains connection 20 2.4.1.2 Mains chokes (3-phase chokes) .22 2.4.1.3 Line fuses for operation class gL and cable cross-sections .26 2.4.1.4 Fuse circuit breakers .27 2.4.1.5 Mains contactor .28 2.4.2 DC supply .29 2.5 Options 30 2.5.1 Control unit (BDE) .30 2.5.2 Brake chopper and braking resistors 32 2.5.2.1 Brake chopper option E31 33 2.5.2.2 Braking resistors .34 2.5.2.3 Thermal overcurrent relay .36 2.5.2.4 Overload relay for braking resistors 37 2.5.3 Mains filters and push-pull chokes 38 2.5.4 Motor filters and output chokes .39 2.5.4.1 Motor du/dt filters 39 2.5.4.2 Output choke .42 2.5.5 Optional assemblies for A10 Control board 44 2.5.5.1 Relay outputs 220 V Option E81 .44 2.5.5.2 Optocoupler, Option E80 46 2.5.6 Option boards for ALSPA MD2000 .48 2.5.6.1 Encoder interface Option E83 .53 2.5.6.2 I/O Interface Option E24 .60 2.5.6.3 Field bus coupler Modnet 1/SFB (Bitbus) Option E11 67 2.5.6.4 Field bus coupler Modnet 1/P (PROFIBUS) Option E11 .69 2.5.6.5 Field bus coupler Modnet 1/MB+ (Modbus Plus) Option E11 72 2.5.6.6 Field bus coupler Modnet1/SN1 (SNET) Option E11 75 2.5.6.7 Technology coprozessor .78 2.5.6.8 Additional power supply NG3 .79 2.5.6.9 Connection kit .81 2.5.6.10 Connection kit Technology coprocessor .82 2.5.6.11 Electronics auxiliary supply .83 2.5.6.12 Analog isolation module 84 2.5.6.13 Function low voltage .85 2.5.6.14 Through-mounting .86 2.5.6.15 Operation on a mains supply with no earth .88 2.5.7 PC Handling and Operating Software .89 2.5.7.1 ALSPA PCS .89 2.5.7.2 Unit-specific files .90 2.5.7.3 RS232 PC connection (V.24) .91 2.5.7.4 RS422 connection for the PC 93 Contents ALSPA MD2000 2.6 Summary circuit diagrams . 95 2.6.1 Summary circuit diagram, ALSPA MD2000 with 3AC supply . 95 2.6.2 Summary circuit diagram, ALSPA MD2000 with DC supply 96 2.7 Connection, terminal wiring 97 2.7.1 Power stack 97 2.7.1.1 3AC supply . 97 2.7.1.2 DC supply 100 2.7.2 Electronics section, A10 control board :X15 103 2.7.2.1 Terminal strip wiring :X15 and signal functions 104 2.7.2.2 Description of terminal strip inputs / outputs 109 2.8 Dimensions, Installation drawing, weights . 113 2.8.1 Alspa MD2000 build-in units 113 2.8.2 Mains chokes for ALSPA MD2000 . 115 2.8.3 Installation drawing for ALSPA MD2000 control unit BDE 117 2.8.4 Dimensions and installation dimensions Base for semiconductor fuses of operating class gR with 110 mm length 119 2.8.5 Dimensions and installation dimensions Fuse isolator for semiconductor fuses with 110 mm length (DIN 43653) 120 2.8.6 Dimensions and installation dimensions Fuse isolator for encapsulated fuses 27.60 . 121 2.8.7 Dimensions and installation dimensions Braking resistors . 122 2.8.8 Dimensions and installation dimensions, motor du/dt filters 123 2.8.9 Dimensions and weights 125 2.8.10 Output choke 126 2.8.11 Dimensions and weights 127 2.8.11.1 Connection and Installation dimensions, Mains filter . 128 2.8.11.2 Connection and installation dimensions, Matching chokes . 132 2.8.12 Electronics auxiliary supply 134 2.8.13 Dimensions and connection Thermal overcurrent release . 135 3 Transport, Installation and Connection 137 3.1 Safety instructions 137 3.2 Storage . 138 3.3 Transport 138 3.4 Installation 138 3.5 Connection and wiring . 139 3.5.1 Potential separation 146 3.6 Installation and connection instructions for EMC . 148 3.7 Specific measures for ensuring electromagnetic compatibility (EMC) . 159 4 Operation and Software . 161 4.1 Unit operation . 161 4.1.1 Software structure 162 4.1.2 Control philosophy . 163 4.2 Parameter adjustment 164 4.3 Menu 166 4.4 Description of parameters and displays 171 5 Commissioning 173 5.1 Safety instructions for commissioning 173 5.2 General . 175 5.3 Mains and motor connection 175 5.4 Sequence diagram . 176 5.5 Commissioning report 180 Contents ALSPA MD2000 6 Help in the event of errors .189 6.1 First value log for error messages .189 6.2 Switching sequence on errors .189 6.3 Event log .189 6.4 Events .189 6.5 Error log 192 6.6 Errors .192 7 Maintenance .197 7.1 Battery for RAM and clock 197 7.1.1 Battery change 197 7.1.2 Technical data of battery 197 7.2 Fans 197 7.3 Power connections 197 7.4 Reforming the link capacitors .198 8 Spare Parts .201 9 Appendix 205 EU – Declaration of Conformity 233 List of diagrams 235 List of Tables .237 Comments from users .239 c 06-1/01 Comments ALSPA MD2000 Expressions used Note: :: : Notes separate important information from the text and give additional information. Important! !! ! Important means that the relevant instruction must be followed exactly to avoid damage. Warning! Warning means that the operator may be injured if the instructions are not followed. Limitation of liability Unless anything to the contrary is contractually agreed, the "General Delivery Terms for Products and Services of the Electrical Industry" ["Allgemeine Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie"] as amended from time to time shall apply. Data, illustrations and descriptions contained in this manual shall not entitle any customer, user or any third party to request any modification whatsoever of equipment previously supplied. In the event of any software modifications and updates, we are not obliged to make such modifications and updates available to customers on a retroactive basis. The contents of this manual were developed and revised with utmost care. However, ALSTOM does not accept any liability for any damage or loss whatsoever which might result from any defects in such documentation. The user shall be solely responsible for the proper and correct use of the ALSPA MD2000 frequency inverter. ALSTOM disclaims any liability whatsoever for improper or incorrect installation or use. Process information and circuit details contained in this manual shall be deemed as being suggestions only, which shall be subject to verification with regard to their suitability for any given application. ALSTOM disclaims any warranty or liability for the suitability of such process information and circuit suggestions with regard to any given application. Data, illustrations, modifications Data and illustrations shall not be deemed as being warranted properties in the legal meaning. Modifications in the interest of technical progress are reserved. Please let us know if you have any suggestions for improvement or modification. A model form can be found on the last pages of this publication. Training ALSTOM offers training programs for additional and supplementary system knowledge Without our prior approval, this document shall not be copied or disclosed to any third party in any manner whatsoever. The recipient hereof or any third party shall not use this document for any improper purpose whatsoever. Translation to any foreign language is not permitted. Any data, dimensions, weights, illustrations and other technical information shall be subject to change without notice, particularly in the interest of further perfecting our equipment. The data and specifications agreed to in the event of an order shall be generally deemed as being the binding basis. © 2001 ALSTOM Power Conversion GmbH 1 Brief description ALSPA MD2000 1 1.1 General ALSPA MD2000 units are processor-controlled pulse inverters with a field-orientated control concept for continuous low-loss speed adjustment of AC motors. The power stack consists of a diode rectifier in a 3-phase bridge circuit on the mains side and an IGBT inverter on the motor side. The basic inverter models are designed for standard applications. Through suitable options (eg. bus couplers, encoder interface) the units can be integrated into automation systems and can also fulfil highly dynamic requirements. Operation of all units is identical throughout the entire type range. Easy familiarisation and operation as well as maximum flexibility were the prime objectives during development. The inverters are operated and parameters adjusted by means of a optional removable control unit (BDE) or using a PC and an PC software package. Connection to automation systems is possible through conventional bus systems (see field bus coupler options). With a mains voltage range from 380 to 480 V build-in units cover the power range from 22 kVA to 330 kVA. In conjunction with standard asynchronous motors the drive capacities provided are therefore as follows: - At unit rated current 18.5 kW to 200 kW, 400 V 21 kW to 230 kW, 480 V - At unit basic load current 15 kW to 160 kW, 400 V 17 kW to 184 kW, 480 V Note: This operating manual applies to the following units: ALSPA MD2000 22/27-400 . 225/275-400 Software version: V3.0 Ref. No.: 029.152 730 Important! ALSPA MD2000 units are designed as standard for operating on earthed networks. 1 Brief description 2 ALSPA MD2000 1.2 Basic operation The link voltage is generated from the mains supply through the mains rectifier. A 3- phase choke connected to the mains supply reduces harmonic currents and serves to decouple the unit from other converters (consumers) on the same supply network. ALSPA MD2000 units are connected as standard to an earthed network. The link voltage is smoothed by high quality electrolytic capacitors. With the motor converter these provide the magnetising reactive power required by the motor and decouple the converter on the mains side from the inverter on the motor side. Through optimised pulse width modulation the motor converter generates from the link voltage a sinusoidal 3-phase system with variable frequency and voltage. A power dump (option) in conjunction with a braking resistor allows braking energy to be used in regenerative operation. Control and regulation of the ALSPA MD2000 are fully digital. Different control structures such as, frequency control, speed control with or without encoder and torque control with or without encoder can be selected, depending on the application requirements. The field-orientated control concept provides control dynamics directly comparable to those of a DC drive. In addition, various inputs and outputs can be connected individually according to the task involved. Thus the drive system can very easily be customised for the requirements of the specific application. RS 422/485 A D I/O CPU Controller SAB 80C 187 Options Encoder Interface Bus Central Control PLC R B *) Powerboard *) *) *) *) M 3~ + - Start Stop Motor Parameter menu enter quit error ready run PC *) Option Fig. 1: Summary circuit diagram, basic layout, operation Brief description 1 ALSPA MD2000 3 1.3 Main features • Consistent range of Types for drives from 15 kW to 250 kW with IGBT inverters • Supply voltage ranges: - 3AC 380 V . 460 V +10 %/ -15 % . 480 V +6 %/ -15 % • Standard design for connection to earthed networks • Output frequency range: 0 . 300 Hz • 120 % overload capacity for 60 s based on unit rated current (Unit rated current = 1.25 ∗ unit basic load current) • 150 % overload capacity for 60 s based on unit basic load current • Standard asynchronous motors can be used without power reduction • High dynamics: Torque rise time: t an = 2 to 8 ms • ALSPA MD2000 units are resistant to idling, short circuit and earth fault • DC system bus supply for several ALSPA MD2000 through DC link connection (option) • 4Q operation (option) through power dump with braking resistor or mains feedback unit (option) • Cooling airflow Power stack cooling air circuit can be remote (optional through- mounting facility) The cooling system can be installed outside the switchgear cubicle • Mains supply power connections at top and motor connections at foot • Motor temperature monitoring by thermistor processing electronics (PTC) • Easy, user-friendly system structure • Consistent and easily learned operation via control unit (option) with plain text display (various languages available) • Extensive additional operating facilities via PC, for example menu control, user-controlled commissioning, oscilloscope function • RS 422 serial interface as standard • Consistent operation through control systems (option) • Connection to automation system through field buses (option): Bitbus, Profibus, Modbus Plus, SNET • Control structures available: - Frequency control - Speed control with or without incremental rotation encoder - Torque control with or without incremental rotation encoder [...]... [A] 22/ 27-400 1 40 32 48 LS 37 .22 097 414 27/33-400 1 48 40 60 LS 37 .22 097 414 33/43-400 1 62 48 72 LS 47 .22 097 415 43/54-400 1 78 62 93 LS 47 .22 097.415 54/62-400 2 90 78 117 LS 47 .22 097 415 62/78-400 2 113 90 135 LS 77 .22 106 813 78/102-400 2 147 113 170 LS 107 .22 084 465 102/ 122- 400 2 176 147 221 LS 107 .22 084 465 122/ 150-400 3 216 176 264 LS 177 .22 092 617 150/178-400 3 257 216 324 LS 247 .22. .. Power reduction curves (Derating) ALSPA MD2000 22 275- 400 14 ALSPA MD2000 60 Technical data 2 Efficiency curves 100 Efficiency h in % 95 90 M=konst 2 M»n 85 80 75 10 20 30 40 50 60 Frequency in Hz Fig 6: ALSPA MD2000 Efficiency curves 22 275- 400 The curves in Fig 6 apply to pulse frequency 3 at a 400 460 V supply voltage ALSPA MD2000 15 2 Technical data 2.3.1 Standards, operating conditions and certificates... x 419 140 Table 2: ALSPA MD2000 frame sizes, AC supply Scope of supply: 6 ALSPA MD2000 Build-in unit, IP20, including mains commutation choke supplied loose Technical data 2 ALSPA MD2000 for DC supply ALSPA MD2000 22 275 kVA, DC 500 630 V Processor-controlled pulse inverter with field-orientated control concept for continuous low-loss speed adjustment of standard AC motors ALSPA MD2000 type Frame... apparent power in kVA at basic load current Overload capacity: 1.5 ∗ basic load current Series *) Based on 3AC 400 V supply voltage Fig 2: ALSPA MD2000 rating plate The following details are required for identifying the unit: - Type No : Serial No : Project No : Option No : ALSPA MD2000 5 2 Technical data 2.2 Series of types ALSPA MD2000 for 3-phase AC connection ALSPA MD2000 22 275 kVA, 3AC 380 48 0... the current rise when the voltage rises This prevents excessive overvoltages at the ALSPA MD2000 mains input ALSPA MD2000 type Frame size Unit output current Rated current Basic load current [A] 22/ 27-400 27/33-400 33/43-400 43/54-400 54/62-400 62/78-400 78/102-400 102/ 122- 400 122/ 150-400 150/178-400 178 /225 -400 225 /275- 400 1 1 1 1 2 2 2 2 3 3 4 4 [A] Max current for 60 s [A] 40 48 62 78 90 113 14 7... 54/62-400 90 117 62 65 72 75 45 51 62/78-400 113 135 78 81 90 94 55 63 78/102-400 147 170 102 106 117 122 75 86 102/ 122- 400 176 221 122 127 140 146 90 103 122/ 150-400 216 264 150 155 172 180 110 126 150/178-400 257 324 178 185 205 214 132 151 178 /225 -400 325 386 225 234 259 270 160 184 225 /275- 400 396 488 275 285 316 330 200 230 Table 5: Technical data at rated current with overload capacity 1.2 x rated... load 2) current [A] Rated 1) current [A] 22/ 27-400 27/33-400 33/43-400 43/54-400 54/62-400 62/78-400 78/102-400 102/ 122- 400 122/ 150-400 150/178-400 178 /225 -400 225 /275- 400 1 1 1 1 2 2 2 2 3 3 4 4 40 48 62 78 90 113 147 176 216 257 325 396 32 40 48 62 78 90 113 147 176 216 257 325 Max current 3) 60 s [A] ALSPA MD2000 for DC supply Ref No 48 60 72 93 117 135 170 221 264 324 386 488 029.146 637 029.14 6... continuous low-loss speed adjustment of standard AC motors ALSPA MD2000 type Frame size Unit input current, 5) mains current eff [A] 22/ 27-400 27/33-400 33/43-400 43/54-400 54/62-400 62/78-400 78/102-400 102/ 122- 400 122/ 150-400 150/178-400 178 /225 -400 225 /275- 400 1 1 1 1 2 2 2 2 3 3 4 4 Unit output current Rated 1) current [A] 43 51 65 82 95 119 154 184 226 268 340 415 Basic load 2) current [A] 40 48 62 7 8... Fig 4: ALSPA MD2000 Overload capacity 1.5 x basic load current ALSPA MD2000 9 2 Technical data The rise in temperature of the cooling air at rated current is ∆υ ≤ 16 °C for the cooling air volume stated and when the installation clearances are maintained 2.2.3 Power loss and cooling air volume ALSPA MD2000 type 22/ 27-400 27/33-400 33/43-400 43/54-400 54/62-400 62/78-400 78/102-400 102/ 122- 400 122/ 150-40 0... LS 247 .22 087 554 178 /225 -400 4 325 257 386 LS 247 .22 087 554 225 /275- 400 4 396 325 488 CA-5-550A 139 073 Table 17: Mains contactors Mains contactors and accessories are stated for 400 V, 50/60 Hz mains voltage Accessories for mains contactors Contactor Interference suppression module LS 37 .22 - LS 47 .22 LS 77 .22 - CA5-550 Table 18: Accessories for 3-phase contactors 28 ALSPA MD2000 LRC-V2-0 15-400 . Operating Manual ALSPA MD2000 22 kVA ... 275 kVA Safety and Operating Instructions for F req uency C onv. 2 Technical data 6 ALSPA MD2000 2.2 Series of types ALSPA MD2000 for 3-phase AC connection ALSPA MD2000 22 ... 275 kVA, 3AC 380 ... 480 V