Mathematical modeling and analysis of organic bulk heterojunction solar cells

147 606 0
Mathematical modeling and analysis of organic bulk heterojunction solar cells

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

Mathematical Modeling and Analysis of Organic Bulk Heterojunction Solar Cells Zhang Teng B.Eng.(Hons.), NUS A Thesis Submitted For the Degree of Doctor of Philosophy Deparment of Chemical and Biomolecular Engineering National University of Singapore May 2014 " .For actually the earth had no roads to begin with, but when many men pass one way, a road is made." - Lu Xun, excerpt from "Hometown", 1921. Typeset with AMS-LATEX. DECLARATION I hereby declare that the thesis is my original work and it has been written by me in its entirety. I have duly acknowledged all the sources of information which have been used in the thesis. This thesis has also not been submitted for any degree in any university previously. Zhang Teng 22 April 2014 Mathematical Modeling and Analysis of Organic Bulk Heterojunction Solar Cells Zhang Teng National University of Singapore Departrment of Chemical and Biomolecular Engineering Singapore 117576, Singapore Abstract Organic photovoltaics have become a promising alternative to today's silicon-based technologies with the potential of providing low-cost, large-area solar cells. However, organic solar cells still su er from signi cantly lower e ciencies than their silicon-based counterparts, and the understanding of their performance limiting factors is hampered by the convoluted morphologies of organic photoactive layers. In this context, this study seeks to establish a multiscale modelling framework to elucidate the structure-property relationships in organic bulk heterojunction (BHJ) solar cells. For this purpose, we have rst generalized the existing device models for organic bilayer and BHJ solar cells by reformulating the interfacial boundary conditions for charge carrier separation and recombination at the donor/acceptor interface. This generalized model could be reduced to either a bilayer or a BHJ model depending on the nature of the interface. The validity of this model has been assessed by calibrating and validating model predictions with experimental current-voltage measurements. In addition, we have utilized the model to investigate the morphology and loss mechanisms in the recently invented pseudo-bilayer solar cells. We employ a two-level modelling approach to investigate the structure-property relations in organic BHJ solar cells: First, we develop a three-dimensional (3D), two-phase device model that resolves the morphological details of representative photoactive layer morphologies; then, we volume-average the local structural details of the photoactive layer to derive a 1D, spatiallysmoothed model that reveals the e ects of inherent morphological characteristics on photovoltaic properties the solar cell in the form of mathematical relations. The spatially-smoothed model is consistent with the existing e ective-medium models, but it captures two essential morphological characteristics not found in existing models: the speci c interfacial area and the donor/acceptor volume fractions. In addition, we derive an analytical model for exciton transport that relates morphological characteristics explicitly with the charge carrier generation rate. This exciton transport model can be directly incorporated into the spatially-smoothed model, allowing it to capture the e ects of morphology and exciton transport on the performance of organic BHJ solar cells. ii With the spatially-smoothed device model derived and validated, we utilize it to investigate the optimum morphology of the recently demonstrated pillar-structured donor/acceptor organic solar cells. We illustrate that the e ective transport and recombination properties of the pillartype morphology are explicit functions of the speci c interfacial area and the donor/acceptor volume fractions. The cross-sectional shape of the pillars, on the other hand, has no major in uence on the performance of this type of solar cells. Based on these closed-form structure-property relations, we establish a fast computational framework to determine the optimal pillar-type morphologies. We further apply the spatially-smoothed device to study the e ect of morphology on the opencircuit voltage of organic solar cells. By solving the spatially-smoothed model analytically at open-circuit, we are able to derive a closed-form relation between the open-circuit voltage and the underlying donor/acceptor morphology. We nd that the in uence of morphology on the open-circuit voltage is attributed to a single morphological parameter: the ratio between the donor volume fraction and the speci c interfacial area. Our ndings are veri ed against detailed two-phase models with a range of randomly generated donor/acceptor morphologies. Finally, we highlight how the present work can be extended towards a hierarchical multiscale modelling framework to derive morphology-property relations in realistic, disordered BHJ morphologies. Keywords: organic solar cells; bulk-heterojunction; morphology; charge carrier transport; recombination; exciton; mathematical modeling; volume-averaging iii Preface This thesis presents topics on the mathematical modeling of organic solar cells with a focus on relating the solar cell performance with the microscopic morphology of the photoactive layer. Chapter introduces the background, motivation, and objectives of this work. In Chapter 2, the mathematical formulations for the existing bilayer and bulk-heterojunction (BHJ) device models are summarized and generalized in the form of a pseudo-bilayer device model. This generalized model could be reduced to either a bilayer or a BHJ model depending on the nature of the donor/acceptor interface. In addition, the implementation procedures for three-dimensional device models with disordered donor/acceptor morphologies are outlined. In Chapter 3, the pseudo-bilayer device model is utilized to study the morphology and loss mechanisms in the recently discovered pseudo-bilayer organic solar cell which contains partially intermixed photoactive layer. Chapter 4-5 present the derivation and veri cation of the spatially-smoothed device model, which represent a key contribution of this thesis. In particular, Chapter demonstrates the development of spatially-smoothed forms of the Poisson and charge carrier continuity equations based on volume-averaging the local charge carrier generation, transport and recombination properties. The spatially-smoothed models not only features the simplicity of existing e ective-medium models, but also captures the e ects of inherent morphological characteristics on the photovoltaic properties the solar cell. In Chapter 5, the spatially-smoothed model is further extended to include the e ect of exciton transport and morphology on the interfacial charge carrier generation rate. With the spatially-smoothed model secured, Chapter 6-7 illustrate two applications of this new modeling framework in elucidating structure-property relationships. In Chapter 6, the spatially-smoothed model is utilized to study the recently demonstrated pillar-structured donor/acceptor organic solar cells. Closed-form expressions are derived for the e ective charge carrier transport and recombination properties of this type of device, and the optimum characteristics of the pillar-type structures are derived. In Chapter 7, the spatially-smoothed model is solved analytically at open-circuit to derive an analytical expression of the open-circuit voltage of organic BHJ solar cells as a function of the underlying morphology. A single morphological parameter is identi ed to govern the open-circuit voltage at leading order. The analytical results in Chapter 6-7 are veri ed with detailed two-phase device modeling with randomly generated donor/acceptor morphologies. Finally, Chapter summarizes the main ndings of this thesis, and discusses possible extensions of the current work. iv The following journal publications are based on research carried out for this doctoral thesis: 1. T. Zhang, E. Birgersson, K. Ananthanarayanan, C. H. Yong, L. N. S. A. Thummalakunta, and J. Luther, Analysis of a device model for organic pseudo-bilayer solar cells, J. Appl. Phys. 112, 084511 (2012). 2. T. Zhang, E. Birgersson, and J. Luther, A spatially-smoothed device model for organic bulk heterojunction solar cells, J. Appl. Phys. 113, 174505 (2013). 3. T. Zhang, E. Birgersson, and J. Luther, Closed-form expression correlating exciton transport and interfacial charge carrier generation with the donor/acceptor morphology in organic bulk heterojunction solar cells. Physica B 456 267 (2015) 4. T. Zhang, E. Birgersson, and J. Luther, Modelling the structure-property relations in pillarstructured donor/acceptor solar cells, Organ. Electron. 15 2742 (2014). 5. T. Zhang, E. Birgersson, and J. Luther, Relating morphological characteristics with the open circuit-voltage of organic bulk-heterojunction solar cells, accepted in Appl. Phys. Express, 2014. v Acknowledgements I owe my deepest gratitude to my PhD advisor, Dr Erik Birgersson, who is the most enthusiastic teacher and one of the smartest people I know. Erik has supported me throughout my PhD journey with thoughtful guidance on my research work, invaluable advise on my career and personal development, whilst allowing me the room to learn and work in my own way. I could not have imagined having a better advisor and mentor for my PhD study. I would like to express my sincere gratitude to Professor Joachim Luther for his insightful comments on my research papers and many enlightening discussions on the physics of solar cells. I would like to thank Associate Professor Peter Ho for the constructive feedback to my manuscripts. I am also in debt to my colleagues - Yong Chian Haw and L. N. S. A, Thummalakunta for the help in conducting experiments for model validations, and Dr Krishnamoorthy Ananthanarayanan, Set Ying Ting, and To Thin Tran for many fruitful discussions and helpful suggestions. I cannot nd words to express my gratitude to my parents who always provide their unconditional love and care. I dedicate the thesis to my ancee , Tang Pan, for her continued love, support, and encouragement for me to pursue an academic career. Finally, I gratefully acknowledged the nancial support from the Solar Energy Research In- stitute of Singapore and the Singapore Economic Development Board for the research work conducted for this thesis. Contents Introduction 1.1 Organic solar cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Device physics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Photoexcitaton and exciton transport . . . . . . . . . . . . . . . . . . . . 1.2.2 Charge carrier separation . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.3 Charge carrier transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.4 Recombination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.5 Summary of the device operation . . . . . . . . . . . . . . . . . . . . . . . photoactive layer morphology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3.1 The bulk-heterojunction morphology . . . . . . . . . . . . . . . . . . . . . 1.3.2 Morphology control and characterization . . . . . . . . . . . . . . . . . . . 11 Device models for organic solar cells . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.4.1 E ective-medium models . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.4.2 Two-phase models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Objectives and outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.3 1.4 1.5 Mathematical formulation 2.1 21 Mathematical formulation for the pseudo-bilayer device model . . . . . . . . . . . 22 2.1.1 Governing equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.1.2 Boundary conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.1.3 Constitutive relations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.2 E ective-medium and two-phase models . . . . . . . . . . . . . . . . . . . . . . . 27 2.3 Three-dimensional two-phase models . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.3.1 Morphology generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.3.2 Numerical implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.3.3 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.4 Device physics of organic pseudo-bilayer solar cells 35 3.1 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 3.2 The device model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 vii Bibliography 113 [22] M. S. White, D. C. Olson, S. E. Shaheen, N. Kopidakis, and D. S. Ginley. Inverted bulk-heterojunction organic photovoltaic device using a solution-derived zno underlayer. Applied Physics Letters, 89(14):{, 2006. [23] C. Z. He, C. M. Zhong, S. J. Su, M. Xu, H. B. Wu, and Y. Cao. Enhanced powerconversion e ciency in polymer solar cells using an inverted device structure. Nature Photonics, 6:591595, 2012. [24] B. Arredondo, C. de Dios, R. Vergaz, A.R. Criado, B. Romero, B. Zimmermann, and U. W'urfel. Performance of ito-free inverted organic bulk heterojunction photodetectors: Comparison with standard device architecture. Organic Electronics, 14(10):2484 { 2490, 2013. [25] Jin Young Kim, Kwanghee Lee, Nelson E. Coates, Daniel Moses, Thuc-Quyen Nguyen, Mark Dante, and Alan J. Heeger. E cient tandem polymer solar cells fabricated by all-solution processing. Science, 317(5835):222{225, 2007. [26] J. You, L. Dou, K. Yoshimura, T. Kato, K. Ohya, T. Moriarty, K. Emery, C-C/ Chen, J. Gao, G. Li, and Y. Yang. A polymer tandem solar cell with 10.6 Nat Commun, 4:1446, 2013. [27] Manu Jaiswal and Reghu Menon. Polymer electronic materials: a review of charge transport. Polymer International, 55(12):1371{1384, 2006. [28] D. Chirvase, Z. Chiguvare, M. Knipper, J. Parisi, V. Dyakonov, and J.C. Hummelen. Temperature dependent characteristics of poly(3 hexylthiophene)-fullerene based heterojunction organic solar cells. Journal of Applied Physics, 93(6):3376{3383, 2003. [29] Z. Zhu, D. Waller, R. Gaudiana, M. Morana, D. M'uhlbacher, M. Scharber, and C. Brabec. Panchromatic conjugated polymers containing alternating donor/acceptor units for photovoltaic applications. Macromolecules, 40(6):1981{1986, 2007. [30] Johan C. Bijleveld, Arjan P. Zoombelt, Simon G. J. Mathijssen, Martijn M. Wienk, Mathieu Turbiez, Dago M. de Leeuw, and Rene A. J. Janssen. Poly(diketopyrrolopyrroleterthiophene) for ambipolar logic and photovoltaics. Journal of the American Chemical Society, 131(46):16616{16617, 2009. PMID: 19886605. [31] Yongye Liang, Danqin Feng, Yue Wu, Szu-Ting Tsai, Gang Li, Claire Ray, and Luping Yu. Highly e cient solar cell polymers developed via ne-tuning of structural and electronic properties. Journal of the American Chemical Society, 131(22):7792{7799, 2009. [32] Yongye Liang, Zheng Xu, Jiangbin Xia, Szu-Ting Tsai, Yue Wu, Gang Li, Claire Ray, and Luping Yu. For the bright future-bulk heterojunction polymer solar cells with power conversion e ciency of 7.4 Advanced Materials, 22(20):E135{E138, 2010. 114 Bibliography [33] S. R Scully, P. B. Armstrong, C. Edder, J. M. J. Frechet, and M. D. McGehee. Long-range resonant energy transfer for enhanced exciton harvesting for organic solar cells. Advanced Materials, 19(19):2961{2966, 2007. [34] Krishna Feron, Warwick J. Belcher, Christopher J. Fell, and Paul C. Dastoor. Organic solar cells: Understanding the role of f'Orster resonance energy transfer. International Journal of Molecular Sciences, 13(12):17019{17047, 2012. [35] Wallace C.H. Choy, editor. Organic Solar Cells Materials and Device Physics. SpringerVerlag London, 2013. [36] R. Kroon, M. Lenes, J. C. Hummelen, P Blom, PBlom, and B. de Boer. Small bandgap polymers for organic solar cells (polymer material development in the last years. Polymer Reviews, 48(6):531{582, 2008. [37] Chih-Wei Chu, Vishal Shrotriya, Gang Li, and Yang Yang. Tuning acceptor energy level for e cient charge collection in copper-phthalocyanine-based organic solar cells. Applied Physics Letters, 88(15):{, 2006. [38] Guangjin Zhao, Youjun He, and Yongfang Li. 6.5poly(3-hexylthiophene) and indene-c60 bisadduct by device optimization. Advanced Materials, 22(39):4355{4358, 2010. [39] P. W. M. Blom, V. D. Mihailetchi, L. J. A. Koster, and D. E. Markov. Device physics of polymer:fullerene bulk heterojunction solar cells. Advanced Materials, 19(12):1551{1566, 2007. [40] Charles L. Braun. Electric eld assisted dissociation of charge transfer states as a mechanism of photocarrier production. The Journal of Chemical Physics, 80(9):4157{4161, 1984. [41] T. E. Goliber and J. H. Perlstein. Analysis of photogeneration in a doped polymer system in terms of a kinetic model for electric- eld-assisted dissociation of charge-transfer states. The Journal of Chemical Physics, 80(9):4162{4167, 1984. [42] M. Lenes, F. B. Kooistra, J. C. Hummelen, I. Van Severen, L. Lutsen, D. Vanderzande, T. J. Cleij, and P. W. M. Blom. Charge dissociation in polymer:fullerene bulk heterojunction solar cells with enhanced permittivity. Journal of Applied Physics, 104(11), 2008. [43] Jiye Lee, Koen Vandewal, Shane R. Yost, Matthias E. Bahlke, Ludwig Goris, Marc A. Baldo, Jean V. Manca, and Troy Van Voorhis. Charge transfer state versus hot exciton dissociation in polymer-fullerene blended solar cells. Journal of the American Chemical Society, 132(34):11878{11880, 2010. [44] E. A. Davis N. F. Mott. Electronic Processes in Non-crystalline Materials. Oxford University press, 1979. Bibliography 115 [45] R. A. Street, J. E. Northrup, and A. Salleo. Transport in polycrystalline polymer thin- lm transistors. Phys. Rev. B, 71:165202, Apr 2005. [46] P. W. M. Blom, M. J. M. de Jong, and M. G. van Munster. Electric- eld and temperature dependence of the hole mobility in poly(p-phenylene vinylene). Phys. Rev. B, 55:R656{ R659, Jan 1997. [47] M. C. J. M. Vissenberg and M. Matters. Theory of the eld-e ect mobility in amorphous organic transistors. Phys. Rev. B, 57:12964{12967, May 1998. [48] C. Tanase, P. W. M. Blom, and D. M. de Leeuw. Origin of the enhanced space-chargelimited current in poly(p-phenylene vinylene). Phys. Rev. B, 70:193202, Nov 2004. [49] W. F. Pasveer, J. Cottaar, C. Tanase, R. Coehoorn, P. A. Bobbert, P. W. M. Blom, D. M. de Leeuw, and M. A. J. Michels. Uni ed description of charge-carrier mobilities in disordered semiconducting polymers. Phys. Rev. Lett., 94:206601, May 2005. [50] Th. B. Singh, N. S. Sariciftci, H. Yang, L. Yang, B. Plochberger, and H. Sitter. Correlation of crystalline and structural properties of c60 thin lms grown at various temperature with charge carrier mobility. Applied Physics Letters, 90(21):{, 2007. [51] H. Yang, T. J. Shin, L. Yang, K. Cho, C.Y. Ryu, and Z. Bao. E ect of mesoscale crystalline structure on the eld-e ect mobility of regioregular poly(3-hexyl thiophene) in thin- lm transistors. Advanced Functional Materials, 15(4):671{676, 2005. [52] Claire H. Woo, Claudia Piliego, Thomas W. Holcombe, Michael F. Toney, and Jean M. J. Frchet. A quantitative correlation between the mobility and crystallinity of photo-crosslinkable p3ht. Macromolecules, 45(7):3057{3062, 2012. [53] R. Mauer, M. Kastler, and F. Laquai. The impact of polymer regioregularity on charge transport and e ciency of p3ht:pcbm photovoltaic devices. Advanced Functional Materials, 20(13):2085{2092, 2010. [54] Elizabeth von Hau , Vladimir Dyakonov, and Jrgen Parisi. Study of eld e ect mobility in pcbm lms and p3ht:pcbm blends. Solar Energy Materials and Solar Cells, 87:149 { 156, 2005. [55] V. D. Mihailetchi, J. Wildeman, and P. W. M. Blom. Space-charge limited photocurrent. Phys. Rev. Lett., 94:126602, Apr 2005. [56] L. J. A. Koster, V. D. Mihailetchi, H. Xie, and P. W. M. Blom. Origin of the light intensity dependence of the short-circuit current of polymer/fullerene solar cells. Applied Physics Letters, 87(20):{, 2005. 116 Bibliography [57] L. Jan Anton Koster, Valentin D. Mihailetchi, Martijn Lenes, and Paul W. M. Blom. Performance Improvement of Polymer: Fullerene Solar Cells Due to Balanced Charge Transport, pages 281{297. Wiley-VCH Verlag GmbH & Co. KGaA, 2009. [58] S. K. Pal, T. Kesti, M. Maiti, F. Zhang, O. Ingan•as, S. Hellstr•om, M. Andersson, F. Os• wald, F. Langa, T. Osterman, T. Pascher, A. Yartsev, and V. Sundstr•om. Geminate charge recombination in polymer/fullerene bulk heterojunction lms and implications for solar cell function. Journal of the American Chemical Society, 132(35):12440{12451, 2010. [59] R. A. Street, Sarah Cowan, and A. J. Heeger. Experimental test for geminate recombination applied to organic solar cells. Phys. Rev. B, 82:121301, Sep 2010. [60] V. D. Mihailetchi, L. J. A. Koster, J. C. Hummelen, and P. W. M. Blom. Photocurrent generation in polymer-fullerene bulk heterojunctions. Phys. Rev. Lett., 93:216601, Nov 2004. [61] R. Mauer, . Howard, I., and F. Laquai. E ect of nongeminate recombination on ll factor in polythiophene/methanofullerene organic solar cells. The Journal of Physical Chemistry Letters, 1(24):3500{3505, 2010. [62] G. Juska, K. Arlauskas, G. Sliauzys, A. Pivrikas, A. J. Mozer, N. S. Sariciftci, M. Scharber, and R. 'Osterbacka. Double injection as a technique to study charge carrier transport and recombination in bulk-heterojunction solar cells. Applied Physics Letters, 87(22):{, 2005. [63] C. G. Shuttle, B. O'Regan, A. M. Ballantyne, J. Nelson, D. D. C. Bradley, and J. R. Durrant. Bimolecular recombination losses in polythiophene: Fullerene solar cells. Phys. Rev. B, 78:113201, Sep 2008. [64] Carsten Deibel, Alexander Wagenpfahl, and Vladimir Dyakonov. In uence of charge carrier mobility on the performance of organic solar cells. physica status solidi, 2(4):175{177, 2008. [65] L. Jan Anton Koster, Martijn Kemerink, Martijn M. Wienk, Klara Maturova, and Rene A. J. Janssen. Quantifying bimolecular recombination losses in organic bulk heterojunction solar cells. Advanced Materials, 23(14):1670{1674, 2011. [66] Gytis Juska, Kristijonas Genevicius, Nerijus Nekrasas, Gytis Sliauzys, and Ronald 'Osterbacka. Two dimensional langevin recombination in regioregular poly(3- hexylthiophene). Applied Physics Letters, 95(1):{, 2009. [67] G. Juska, K. Genevicius, N. Nekraas, G. Sliauzys, and G. Dennler. Trimolecular recombination in polythiophene: fullerene bulk heterojunction solar cells. Applied Physics Letters, 93(14):{, 2008. Bibliography 117 [68] R. A. Street, M. Schoendorf, A. Roy, and J. H. Lee. Interface state recombination in organic solar cells. Phys. Rev. B, 81:205307, May 2010. [69] Thomas Kirchartz, Bart E. Pieters, James Kirkpatrick, Uwe Rau, and Jenny Nelson. Recombination via tail states in polythiophene:fullerene solar cells. Phys. Rev. B, 83:115209, Mar 2011. [70] Gert-Jan A. H. Wetzelaer, Martijn Kuik, and Paul W. M. Blom. Identifying the nature of charge recombination in organic solar cells from charge-transfer state electroluminescence. Advanced Energy Materials, 2(10):1232{1237, 2012. [71] Sarah R. Cowan, Wei Lin Leong, Natalie Banerji, Gilles Dennler, and Alan J. Heeger. Identifying a threshold impurity level for organic solar cells: Enhanced rst-order recombination via well-de ned pc84bm traps in organic bulk heterojunction solar cells. Advanced Functional Materials, 21(16):3083{3092, 2011. [72] R. A. Street, J. E. Northrup, and B. S. Krusor. Radiation induced recombination centers in organic solar cells. Phys. Rev. B, 85:205211, May 2012. [73] Ying Ting Set, Marc Daniel Heinemann, Erik Birgersson, and Joachim Luther. On the origin of the quadrant i semicircle in intensity-modulated photocurrent spectra of p3ht:pcbm bulk heterojunction solar cells: Evidence of degradation-related trap-assisted recombination. The Journal of Physical Chemistry C, 117(16):7993{8000, 2013. [74] Christopher R. McNeill. Morphology of all-polymer solar cells. Energy Environ. Sci., 5:5653{5667, 2012. [75] Xiaoniu Yang and Joachim Loos. Toward high-performance polymer solar cells: The importance of morphology control. Macromolecules, 40(5):1353{1362, 2007. [76] Harald Hoppe and Niyazi Serdar Sariciftci. Morphology of polymer/fullerene bulk heterojunction solar cells. J. Mater. Chem., 16:45{61, 2006. [77] B. Viktor Andersson, Anna Herland, Sergej Masich, and Olle Ingan'as . Imaging of the 3d nanostructure of a polymer solar cell by electron tomography. Nano Letters, 9(2):853{855, 2009. PMID: 19119912. [78] Ryan C. Nieuwendaal, Hyun Wook Ro, David S. Germack, R. Joseph Kline, Michael F. Toney, Calvin K. Chan, Amit Agrawal, David Gundlach, David L. VanderHart, and Dean M. Delongchamp. Measuring domain sizes and compositional heterogeneities in p3ht-pcbm bulk heterojunction thin lms with 1h spin di usion nmr spectroscopy. Advanced Functional Materials, 22(6):1255{1266, 2012. [79] C. Groves, R. A. Marsh, and N. C. Greenham. Monte carlo modeling of geminate recombination in polymer-polymer photovoltaic devices. The Journal of Chemical Physics, 129(11):{, 2008. 118 Bibliography [80] Jonathan A. Bartelt, Zach M. Beiley, Eric T. Hoke, William R. Mateker, Jessica D. Douglas, Brian A. Collins, John R. Tumbleston, Kenneth R. Graham, Aram Amassian, Harald Ade, Jean M. J. Frechet, Michael F. Toney, and Michael D. McGehee. The importance of fullerene percolation in the mixed regions of polymer-fullerene bulk heterojunction solar cells. Advanced Energy Materials, 3(3):364{374, 2013. [81] J. F. vanDuren, X. Yang, J. Loos, C. W. T. Bulle-Lieuwma, A. B. Sieval, J. C. Hummelen, and R. A. J. Janssen. Relating the morphology of poly(p-phenylene vinylene)/methanofullerene blends to solar-cell performance. Advanced Functional Materials, 14(5):425{434, 2004. [82] F. Padinger, R.S. Rittberger, and N.S. Sariciftci. E ects of postproduction treatment on plastic solar cells. Advanced Functional Materials, 13(1):85{88, 2003. [83] Youngkyoo Kim, Stelios A. Choulis, Jenny Nelson, Donal D. C. Bradley, Ste an Cook, and James R. Durrant. Device annealing e ect in organic solar cells with blends of regioregular poly(3-hexylthiophene) and soluble fullerene. Applied Physics Letters, 86(6):{, 2005. [84] Gang Li, Vishal Shrotriya, Yan Yao, and Yang Yang. Investigation of annealing e ects and lm thickness dependence of polymer solar cells based on poly(3-hexylthiophene). Journal of Applied Physics, 98(4):{, 2005. [85] Marisol Reyes-Reyes, Kyungkon Kim, and David L. Carroll. High-e ciency photovoltaic devices based on annealed poly(3-hexylthiophene) and 1-(3-methoxycarbonyl)-propyl-1phenyl-(6,6)c61 blends. Applied Physics Letters, 87(8):{, 2005. [86] Sean E. Shaheen, Christoph J. Brabec, N. Serdar Sariciftci, Franz Padinger, Thomas Fromherz, and Jan C. Hummelen. 2.5 Applied Physics Letters, 78(6):841{843, 2001. [87] M. T. Rispens, A. Meetsma, R. Rittberger, C. J. Brabec, N. S. Sariciftci, and J. C. Hummelen. In uence of the solvent on the crystal structure of pcbm and the e ciency of mdmo-ppv:pcbm plastic solar cells. Chem. Commun., pages 2116{2118, 2003. [88] T. Martens, J. D'Haen, T. Munters, Z. Beelen, L. Goris, J. Manca, M. D'Olieslaeger, D. Vanderzande, L. De Schepper, and R. Andriessen. Disclosure of the nanostructure of mdmo-ppv:pcbm bulk hetero-junction organic solar cells by a combination of spm and tem. Synthetic Metals, 138(12):243 { 247, 2003. [...]... (a) the typical structure of an organic bulk heterojunction solar cell, and (b) length scales for the donor/acceptor blend in an averaging volume 4.2 44 49 Simulated (lines) and measured (symbols) current densities for organic BHJ solar cells under AM1.5 solar spectrum: the training set with an illumination intensity of 1 sun (N), and test sets with intensities of 0.55 sun ( ) and 0.75 sun ( ) 4.3... carriers, which are bound in the form of excitons in organic 1.1 Organic solar cells 3 Figure 1.2: Schematic of a typical organic solar cell semiconductors A major milestone in the development of organic photovoltaic devices is the concept of bilayer heterojunction solar cells introduced by Tang et al in 1986 [17] The idea behind this concept is to form an interface between two organic materials with di erent... smaller optical bandgaps is therefore an e ective route to enhance the PCE of organic solar cells, as it allows absorption into the near-infrared portion of the solar spectrum Some examples of low-bandgap polymers include PCPDTBT synthesized by Brabec et al [29] with a bandgap of ~1:5 eV; PDPP3T reported by Janssen et al [30] with a low bandgap of ~1:3 eV; the 1:6 eV bandgap polymers PTB7 [31] and PBDT-TT-CF... characterizing organic solar cells can be found in [74, 101] 1.4 Device models for organic solar cells The interplay between physics and morphology hampers the interpretation of experimental ndings and the understanding of the inherent photovoltaic processes { especially since it is di cult 1.4 Device models for organic solar cells 13 to achieve precise control, as well as accurate quanti cation, of the active... photo-degradation of active materials [10, 11, 12, 13], further hamper their commercialization In order to further enhance the performance and stability of organic solar cells, further research and development are needed in the theoretical understanding of device physics, the design and synthesis of new materials, the development of new device architectures, as well as the characterization and control of the... of organic solar cells [80] 1.3.2 Morphology control and characterization Due to the signi cant in uence of D/A morphology on the solar cell operation, morphology engineering is an e ective route to improving the performance of organic solar cells The solution processing of D/A blends, however, allows for limited control over the resulting nanoscale morphology The the domain size and connectivity of. .. List of Figures 1.1 Research-cell e ciencies of emerging PV technologies over the past decade 2 1.2 Schematic of a typical organic solar cell 3 1.3 Molecular structures and band diagrams for the donor material P3HT and the acceptor material PC60 BM 5 1.4 Photovoltaic processes in an organic solar cell 8 1.5 Schematics of the organic bulk- heterojunction. .. rst generation of organic solar cells have a homojunction structure, in which a single layer of organic semiconductor is swandwiched between two metal electrodes of di erent work functions [15, 16] This type of solar cells usually have e ciencies less than 0.1%, because the electric eld generated by the asymmetrical work functions of the electrodes is insu cient to drive the separation of charge carriers,... low-temperature and high-throughput 1 2 1.1 Organic solar cells Figure 1.1: Research-cell e ciencies of emerging PV technologies over the past decade The data is extracted from Ref 4 roll-to{roll printing process [7, 8, 9] In addition, the synthetic variability of organic materials provides ample opportunities to continue enhancing and optimizing the optoelectronic properties of organic solar cells, as well... reduce the cost of active materials Despite of these advantages, organic solar cells still exhibit much lower photo-conversion e ciencies as compared to their wafer-based counterpart, primarily due to the low charge carrier mobility, the strong exciton binding energy, and the relatively narrow absorption spectrum of most organic semiconductors [5] Stability issues of organic solar cells, arising partly . Mathematical Modeling and Analysis of Organic Bulk Heterojunction Solar Cells Zhang Teng B.Eng.(Hons.), NUS A Thesis Submitted For the Degree of Doctor of Philosophy Deparment of Chemical and. 22 April 2014 Mathematical Modeling and Analysis of Organic Bulk Heterojunction Solar Cells Zhang Teng National University of Singapore Departrment of Chemical and Biomolecular Engineering Singapore. volume-averaging iii Preface This thesis presents topics on the mathematical modeling of organic solar cells with a focus on relating the solar cell performance with the microscopic morphology of the photoactive layer. Chapter

Ngày đăng: 09/09/2015, 11:20

Từ khóa liên quan

Mục lục

  • Introduction

    • Organic solar cells

    • Device physics

      • Photoexcitaton and exciton transport

      • Charge carrier separation

      • Charge carrier transport

      • Recombination

      • Summary of the device operation

    • photoactive layer morphology

      • The bulk-heterojunction morphology

      • Morphology control and characterization

    • Device models for organic solar cells

      • Effective-medium models

      • Two-phase models

    • Objectives and outline

  • Mathematical formulation

    • Mathematical formulation for the pseudo-bilayer device model

      • Governing equations

      • Boundary conditions

      • Constitutive relations

    • Effective-medium and two-phase models

    • Three-dimensional two-phase models

      • Morphology generation

      • Numerical implementation

      • Discussion

    • Summary

  • Device physics of organic pseudo-bilayer solar cells

    • Experiments

    • The device model

      • Constitutive relations

      • Numerics

    • Calibration and validation

    • Results and discussion

    • Summary

  • Spatially-smoothed model for organic bulk heterojunction solar cells

    • Introduction

    • Derivation of the spatially-smoothed model

      • Basic definitions

      • Two-phase formulation

      • Volume-averaging of electric potential

      • Volume-averaging of charge carrier continuity equations

      • Comparison with existing formulation

    • Numerical implementation

    • Calibration and validation

    • Effective material properties for a perfect blend

    • Summary

    • Appendix: Derivation of Eq. ??

  • A Closed-form expression for the interfacial charge carrier generation rate

    • Introduction

    • Analysis

      • Functional forms

      • Closed-form expressions

    • Verification and discussion

    • Conclusions

  • Modeling the structure-property relations in pillar-structured organic solar cells

    • Introduction

    • The spatially-smoothed device model

    • Structure-property relations for pillar-structured organic solar cells

    • Optimization of the morphological parameters of pillar structures

    • Summary

  • Relating the open-circuit voltage with morphological characteristics of organic BHJ solar cells

    • Introduction

    • Derivation

    • Discussion

    • Summary

  • Conclusions and outlook

    • Summary and conclusions

    • Recommendations for future work

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan