Handbook of Comparative World Steel Standards Part 14 pps

40 1K 0
Handbook of Comparative World Steel Standards Part 14 pps

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

512 Former National Standards Superseded by CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards DIN 1629:1984 Seamless Circular Unalloyed Steel Tubes Subject to Special Requirements Superceded by: EN 10208-1:1997 Steel Pipes for Pipe Lines for Combustible Fluids – Technical Delivery Conditions – Part 1: Pipes of Requirement Class A EN 10216-1:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 1: Non-Alloy Steel Tubes with Specified Room Temperature Properties EN 10217-1:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 1: Non-Alloy Steel Tubes with Specified Room Temperature Properties EN 10224:2002 Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous Liquids Including Water for Human Consumption – Technical Delivery Conditions EN 10297-1:2003 Seamless Circular Steel Tubes for Mechanical and General Engineering Purposes – Technical Delivery Conditions – Part 1: Non-Alloy and Alloy Steel Tubes DIN 17173:1985 Seamless Circular Tubes Made from Steels with Low Temperature Toughness Superceded by: EN 10216-4:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 4: Non-alloy and Alloy Steel Tubes with Specified Low Temperature Properties DIN 17174:1985 Welded Circular Tubes of Hear-Resistant Steels Superceded by: EN 10217-4:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 4: Electric Welded Non-alloy Steel Tubes with Specified Low Temperature Properties EN 10217-6:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 6: Submerged Arc Welded Non- Alloy Steel Tubes with Specified Low Temperature Properties DIN 17175:1979 Seamless Tubes of Heat-resistant Steels Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties DIN 17177:1979 Electric Pressure-welded Steel Tubes for Elevated Temperatures Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties DIN 17178:1986 Welded Circular Fine Grain Steel Tubes Subject to Special requirements – Technical Delivery Conditions Superceded by: EN 10217-3:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 3: Alloy Fine Grain Steel Tubes DIN 17179:1986 Seamless Circular Fine Grain Steel Tubes Subject to Special Requirements – Technical Delivery Conditions Superceded by: EN 10216-3:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 3: Alloy Fine Grain Steel Tubes DIN 17204:1990 Seamless Circular Tubes Made from Steels for Quenching and Tempering – Technical Delivery Conditions Superceded by: EN 10297-1:2003 Seamless Circular Steel Tubes for Mechanical and General Engineering Purposes – Technical Delivery Conditions – Part 1: Non-alloy and Alloy Steel Tubes DIN 2391-2:1994 Seamless Precision Steel Tubes Superceded by: EN 10305-1:2002 Steel Tubes for Precision Applications – Technical Delivery Conditions – Part 1: Seamless Cold Drawn Tubes Appendix 7 Former National Standards Superseded by CEN Standards 513 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards DIN 2393-2:1994 Welded Precision Steel Tubes Superceded by: EN 10305-2:2003 Steel Tubes for Precision Applications – Technical Delivery Conditions – Part 2: Welded Cold Drawn Tubes DIN 2394-2:1994 Welded and Sized Precision Steel Tubes – Technical Delivery Conditions Superceded by: EN 10305-3:2003 Steel Tubes for Precision Applications – Technical Delivery Conditions – Part 3: Welded Cold Sized Tubes AFNOR NF A49-111:1978 Plain End Seamless Tubes of Commercial Quality for General Purposes at Mean Pressure Superceded by: EN 10216-1:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 1: Non-Alloy Steel Tubes with Specified Room Temperature Properties AFNOR NF A49-112:1987 Plain End Seamless Hot Rolled Tubes with Specified Room Temperature Properties and with Special Delivery Conditions – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-1:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 1: Non-Alloy Steel Tubes with Specified Room Temperature Properties AFNOR NF A 49-142:1987 Longitudinally Pressure Welded Plain Ended and Hot Finished Tubes. Diameters from 13,5 to 168,3 mm with Specified Room Temperature Properties and with Special Delivery Conditions – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-1:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 1: Non-Alloy Steel Tubes with Specified Room Temperature Properties AFNOR NF A 49-150:1985 Steel Tubes. Welded Tubes Intended to be Coated or Protected for use in Water Piping Systems – Dimensions – Technical Delivery Conditions. Superceded by: EN 10224:2002 Non-Alloy Steel Tubes and Fittings for the Conveyance of Aqueous Liquids Including Water for Human Consumption – Technical Delivery Conditions AFNOR NF A 49-210:1985 Steel Tubes: Seamless Cold Drawn Tubes for Fluid Piping – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-211:1989 Steel Tubes; Seamless Plain-End Tubes in Unalloyed Steels for Fluid Piping at Elevated Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-213:1990 Seamless Unalloyed and Mo and Cr-Mo Alloyed Steel Tubes for Use at High Temperatures – Dimensions (with Normal Tolerances) – Technical Delivery Conditions Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-215:1981 Seamless Tubes for Ferritic Non-Alloy and Alloy Steel Heat Exchangers – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-219:1990 Non-Alloy and Mo and Cr-Mo Alloy Steel Seamless Tubes for Furnaces – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-2:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Non-Alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-230:1985 Steel Tubes: Plain end Seamless Tubes for Pressure Vessels and Piping Systems Used at Low Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10216-4:2002 Seamless Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 4: Non-alloy and Alloy Steel Tubes with Specified Low Temperature Properties AFNOR NF A 49-240:1983 Steel Tubes: Plain Ended Steel Tubes Longitudinally Welded Without Fusion for Pressure Vessels and Piping Systems at Low Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-4:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 4: Electric Welded Non-alloy Steel Tubes with Specified Low Temperature Properties 514 Former National Standards Superseded by CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards AFNOR NF A 49-241:1986 Steel Tubes - Longitudinally Pressure Welded Plain End Tubes in Non-Alloyed Steel Grades for Fluid Piping up to 425°C – Diameters From 21.3 mm to 168.3 mm – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-242:1985 Longitudinally Pressure Welded Tubes D Inferior or Equal to 168.3 mm in Non-Alloyed and Low Alloyed Steels Used at Medium Elevated Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-243:1985 Longitudinally Pressure Welded Tubes D Inferior or Equal to 168.3 mm in Non-Alloyed and Ferritic Alloyed Steels, Used at Elevated Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-245:1986 Longitudinally Pressure Welded Tubes from Non-Alloy and Ferritic Alloy Steels for Heat Exchangers in Diameters From 15.9 mm and 76.1 mm Inclusive – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties AFNOR NF A 49-252:1982 Welded Non-Alloy Steel Tubes of Diameters 168.3 mm to 1220 mm Used at Averagely Elevated Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties EN 10217-5:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 5: Submerged Arc Welded Non- alloy and Alloy Steel Tubes with Specified Elevated Temperatures Properties AFNOR NF A 49-253:1982 Longitudinally Fusion Welded Non-Alloy Steel and Ferritic Alloy Steel Tubes for Use at Elevated Temperatures – Dimensions – Technical Delivery Conditions Superceded by: EN 10217-2:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 2: Electric Welded Non-alloy and Alloy Steel Tubes with Specified Elevated Temperature Properties EN 10217-5:2002 Welded Steel Tubes for Pressure Purposes – Technical Delivery Conditions – Part 5: Submerged Arc Welded Non- alloy and Alloy Steel Tubes with Specified Elevated Temperatures Properties AFNOR NF A 49-310:1994 Seamless Precision Tubes for Mechanical Application – Dimensions – Technical Delivery Conditions Superceded by: EN 10305-1:2002 Steel Tubes for Precision Applications – Technical Delivery Conditions – Part 1: Seamless Cold Drawn Tubes AFNOR NF A 49-311:1974 Seamless Tubes for Mechanical Application – Dimensions – Technical Delivery Conditions Superceded by: EN 10297-1:2003 Seamless Circular Steel Tubes for Mechanical and General Engineering Purposes – Technical Delivery Conditions – Part 1: Non-alloy and Alloy Steel Tubes AFNOR NF A 49-323:1978 Steel Tubes: Jacks for Hydraulic Transmissions; Cold Rolled or Drawn Seamless Tubes, Type – Ready for Use – Dimensions – Technical Delivery Conditions Superceded by: EN 10305-1:2002 Steel Tubes for Precision Applications – Technical Delivery Conditions – Part 1: Seamless Cold Drawn Tubes AFNOR NF A 49-341:1975 Precision Welded Tubes for Mechanical Application – Dimensions – Technical Delivery Conditions Superceded by: EN 10296-1: 2003 Welded Circular Steel Tubes for Mechanical and General Engineering Purposes – Technical Delivery Conditions – Part 1: Non-Alloy and Alloy Steel Tubes Appendix 7 Former National Standards Superseded by CEN Standards 515 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards AFNOR NF A 49-343:1980 Longitudinally Welded D Inferior or Equal to 168.3 mm for Engineering Use – Dimensions – Technical Delivery Conditions Superceded by: EN 10296-1: 2003 Welded Circular Steel Tubes for Mechanical and General Engineering Purposes – Technical Delivery Conditions – Part 1: Non-Alloy and Alloy Steel Tubes 516 Former National Standards Superseded by CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 6: Steel Forgings Former National Standards Superseded by EN Standards Current Standards BSI BS 29:1976 Carbon Steel Forgings Above 150 mm Ruling Section (Withdrawn) Superseded by: EN 10250-2:2000 Corr 1 Open Die Steel Forgings for General Engineering Purposes – Part 2: Non-Alloy Quality and Special Steels CORR 11041 BSI BS 1503:1989 Amd 3 Steel Forgings for Pressure Purposes (Withdrawn) Superseded by: EN 10222 Steel Forgings for Pressure Purposes EN 10222-1:1998 General Requirements for Open Die Forgings EN 10222-2:2000 Ferritic and Martensitic Steels with Specified Elevated Temperature Properties EN 10222-3:1999 Nickel Steels with Specified Low-Temperature EN 10222-4:1999 Weldable Fine-Grain Steels with High Proof Strength EN 10222-5:2000 Martensitic, Austenitic and Austenitic-Ferritic Stainless Steels BSI BS 4670:1971 Alloy Steel Forgings (Withdrawn) Superseded by: EN 10250-3:2000 Open Die Steel Forgings for General Engineering Purposes – Part 3: Alloy Special Steels DIN 17103:1989 Weldable Fine Grain Structural Steel Forgings; Technical Delivery Conditions (Withdrawn) DIN 17243:1987 Weldable Heat Resisting Steel Forgings and Rolled or Forged Steel Bars; Technical Delivery Conditions (Withdrawn) Superseded by: EN 10222-1:1998 Steel Forgings for Pressure Purposes – Part 1: General Requirements for Open Die Forgings DIN 17280:1985 Steels with Low Temperature Toughness; Technical Delivery Conditions for Plate, Sheet, Strip, Wide Flats, Sections, Bars and Forgings (Withdrawn) DIN 17440:1996 Stainless Steels- Technical Delivery Conditions for Plates, Hot Rolled Strip and Bars for Pressure Purposes, Drawn Wire and Forgings (Withdrawn) DIN 17100:1980 Steels for General Structural Purposes; Quality Standard (Withdrawn) Partially Superseded by: EN 10222-1:1998 Steel Forgings for Pressure Purposes – Part 1: General Requirements for Open Die Forgings DIN 17243:1987 Weldable Heat Resisting Steel Forgings and Rolled or Forged Steel Bars; Technical Delivery Conditions (Withdrawn) Superseded by: EN 10222 Steel Forgings for Pressure Purposes EN 10222-1:1998 General Requirements for Open Die Forgings EN 10222-2:2000 Ferritic and Martensitic Steels with Specified Elevated Temperature Properties (Includes Corrigendum AC: 2000) EN 10273:2000 Hot Rolled Weldable Steel Bars for Pressure Purposes with Specified Elevated Temperature DIN 17100:1980 Steels for General Structural Purposes; Quality Standard (Withdrawn) Superseded by: EN 10250 Open Die Steel Forgings for General Engineering Purposes EN 10250-1:1999 General EN 10250-2:2000 Non-Alloy Quality and Special Steels Appendix 7 Former National Standards Superseded by CEN Standards 517 Handbook of Comparative World Steel Standards Chapter 6: Steel Forgings (Continued) Former National Standards Superseded by EN Standards Current Standards DIN 17440:1996 Stainless Steels-Technical Delivery Conditions for Plates, Hot Rolled Strip and Bars for Pressure Purposes, Drawn Wire and Forgings (Withdrawn) Partially Superseded by: EN 10250 Open Die Steel Forgings for General Engineering Purposes EN 10250-1:1999 General EN 10250-4:2000 Open Die Steel Forgings for General Engineering Purposes AFNOR NF A36-601:1980 Pièces Forgées en Acier Soudable pour Chaudières et Appareils à Pression- Aciers au Carbone et Carbone- Manganèse-Nuances et Qualités (Withdrawn) AFNOR NF A36-602:1988 Pièces Forgées en Acier Soudable pour Chaudières et Appareils à Pression – Aciers Alliés au Mo, au Mn-Mo et au Cr-Mo Nuances et Qualités (Withdrawn) AFNOR NF A36-603:1988 Pièces Forgées en Acier Soudable pour Chaudières et Appareils à Pression-Aciers Alliés à Haute Limite d’Élasticité Nuances et Qualités (Withdrawn) AFNOR NF A36-607:1984 Pièces Obtenues par Forgeage Libre ou Estampage en Aciers Inoxydables Austénitiques pour Chaudières et Appareils à Pression – Nuances et Qualités (Withdrawn) Superseded by: EN 10222 Steel Forgings for Pressure Purposes EN 10222-1:1998 General Requirements for Open Die Forgings EN 10222-3:1999 Nickel Steels with Specified Low Temperature Properties. EN 10222-4:1999 Weldable Fine Grain Steels with High Proof Strength EN 10222-2:2000 Ferritic and Martensitic Steels with Specified Elevated Temperature Properties EN 10222-5:2000 Martensitic, Austenitic and Austenitic-Ferritic Stainless Steels AFNOR NF A36-612:1982 Pièces Forgées d’Usage Général – Aciers Non Alliés (Withdrawn) AFNOR NF A36-613:1986 Pièces Forgées d’Usage Général – Aciers Inoxydables (Withdrawn) Superseded by: EN 10250-1:1999 Open Die Steel Forgings for General Engineering Purposes – Part 1: General Requirements AFNOR NF A36-612:1982 Pièces Forgées d’Usage Général – Aciers Non Alliés (Withdrawn) Superseded by: EN 10250-2:2000 Open Die Steel Forgings for General Engineering Purposes – Part 2: Non-Alloy Quality and Special Steels AFNOR NF A36-613:1986 Pièces Forgées d’Usage Général – Aciers Inoxydables (Withdrawn) Superseded by: EN 10250-4:2000 Open Die Steel Forgings for General Engineering Purposes – Part 4: Stainless Steels 518 Former National Standards Superseded by CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 7: Steel Castings Former National Standards Superseded by EN Standards Current EN Standard BSI BS 1504:1976 Steel Castings for Pressure Purposes (Withdrawn) Superseded by: EN 10213 Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-2:1996 Steel Grades for Use at Room Temperature and at Elevated Temperature EN 10213-3:1996 Steels for Use at Low Temperatures EN 10213-4:1996 Austenitic and Austenitic-Ferritic Steel Grades DIN 17182:1992 General Purpose Steel Castings with Enhanced Weldability and Higher Toughness; Technical Delivery Conditions (Withdrawn) Partially Superseded by: EN 10213 Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-3:1996 Steels for Use at Low Temperatures DIN 17245:1987 Ferritic Steel Castings with Elevated Temperature Properties; Technical Delivery Conditions (Withdrawn) Superseded by: EN 10213: Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-2:1996 Steel Grades for Use at Room Temperature and at Elevated Temperature DIN 17445:1984 Stainless Steel Castings; Technical Delivery Conditions (Withdrawn) Partially Superseded by: EN 10213 Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-4:1996 Austenitic and Austenitic-Ferritic Steel Grades DIN 17445:1984 Stainless Steel Castings; Technical Delivery Conditions (Withdrawn) Superseded by: EN 10213 Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-4:1996 Austenitic and Austenitic-Ferritic Steel Grades EN 10283:1999 Corrosion Resistant Steel Castings DIN 17465:1993 Heat Resisting Steel Castings Superceded by: EN 10295:2002 Heat Resistant Steel Castings. AFNOR NF A 32-057:1981 Steel Grades and Related Alloys- Refractory Moulds Superceded by: EN 10295:2002 Heat Resistant Steel Castings. AFNOR NF A32-055:1985 Produits de Fonderie–Aciers Moulés Soudables pour Chaudières et Appareils à Pression (Withdrawn) Superseded by: EN 10213 Steel Castings for Pressure Purposes EN 10213-1:1996 General EN 10213-2:1996 Steel Grades for Use at Room Temperature and at Elevated Temperature EN 10213-3:1996 Steels for Use at Low Temperatures EN 10213-4:1996 Austenitic and Austenitic-Ferritic Steel Grades Appendix 7 Former National Standards Superseded by CEN Standards 519 Handbook of Comparative World Steel Standards Chapter 8: Wrought Stainless Steels and Heat-Resisting Steels Former National Standards Superseded by EN Standards Current EN Standards BSI BS 970-1:1991 Wrought Steels for Mechanical and Allied Engineering Purposes – Part 1: General Inspection and Testing Procedures and Specific Requirements for Carbon, Carbon Manganese, Alloy and Stainless Steels (Withdrawn) Partially Superseded by: BS 970-1:1996 Specification for Wrought Steels for Mechanical and Allied Engineering Purposes – Part 1: General Inspection And Testing Procedures and Specific Requirements for Carbon, Carbon Manganese, Alloy and Stainless Steels EN 10083-3:1996 Quenched and Tempered Steels – Part 3: Technical Delivery Conditions for Boron Steels EN 10088-2:1995 Stainless Steels – Part 2: Technical Delivery Conditions for Sheet/Plate and Strip for General Purposes EN 10088-3:1995 Stainless Steels – Part 3: Technical Delivery Conditions for Semi-Finished Products, Bars, Rods and Sections for General Purposes BSI BS 1449-2:1983 Amd 4 Steel Plate, Sheet and Strip – Part 2: Specification for Stainless and Heat-Resisting Steel Plate, Sheet and Strip AMD 9648 (Withdrawn) Superseded by: EN 10029:1991 Specification for Tolerances on Dimensions, Shape and Mass for Hot Rolled Steel Plates 3 Mm Thick or Above EN 10048:1997 Hot Rolled Narrow Steel Strip – Tolerances on Dimensions and Shape EN 10051:1992 Specification for Continuously Hot-Rolled Uncoated Plate, Sheet and Strip of Non-Alloy and Alloy Steels – Tolerances on Dimensions and Shape EN 10095:1999 Heat Resisting Steels and Nickel Alloys EN 10258:1997 Cold-Rolled Stainless Steel Narrow Strip and Cut Lengths – Tolerances on Dimensions and Shape EN 10259:1997 Cold-Rolled Stainless and Heat Resisting Steel Wide Strip and Plate/Sheet – Tolerances on Dimensions and Shape BSI BS 970-1:1991 Wrought Steels for Mechanical and Allied Engineering Purposes – Part 1: General Inspection and Testing Procedures and Specific Requirements for Carbon, Carbon Manganese, Alloy and Stainless Steels Partially Superseded by: EN 10084:1998 Case Hardening Steels – Technical Delivery Conditions EN 10085:2001 Nitriding Steel – Technical Delivery Conditions EN 10087:1999 Free Cutting Steels – Technical Delivery Conditions for Semi-Finished Products, Hot Rolled Bars and Rods EN 10095:1999 Heat Resisting Steels and Nickel Alloys EN 10250-4:2000 Open Die Steel Forgings for General Engineering Purposes – Part 4: Stainless Steels DIN 17440:1985 Stainless Steels; Technical Delivery Conditions for Plate and Sheet, Hot Rolled Strip, Wire Rod, Drawn Wire, Steel Bars, Forgings and Semi-Finished Products DIN 17441:1985 Stainless Steels; Technical Delivery Conditions for Cold Rolled Strip and Slit Strip and for Plate and Sheet Cut Therefrom Superseded by: EN 10088-2:1995 Stainless Steels – Part 2: Technical Delivery Conditions for Sheet/Plate and Strip for General Purposes DIN 17440:1985 Stainless Steels; Technical Delivery Conditions for Plate and Sheet, Hot Rolled Strip, Wire Rod, Drawn Wire, Steel Bars, Forgings and Semi-Finished Products Partially Superseded by: EN 10088-3:1995 Stainless Steels – Part 3: Technical Delivery Conditions for Semi-Finished Products, Bars, Rods and Sections for General Purposes DIN 17440:1985 Stainless Steels; Technical Delivery Conditions for Plate and Sheet, Hot Rolled Strip, Wire Rod, Drawn Wire, Steel Bars, Forgings and Semi-Finished Products Partially Superseded by: EN 10250-4:2000 Open Die Steel Forgings for General Engineering Purposes – Part 4: Stainless Steels 520 Former National Standards Superseded by CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 8: Wrought Stainless Steels and Heat-Resisting Steels (Continued) Former National Standards Superseded by EN Standards Current EN Standards AFNOR NF A35-573:1990 Produits Sidérurgiques- Aciers Inoxydables d’Usage Général-Tôles, Larges Bandes et Feuillards Superseded by: EN 10088-2:1995 Stainless Steels – Part 2: Technical Delivery Conditions for Sheet/Plate and Strip for General Purposes AFNOR NF A35-574:1990 Produits Sidérurgiques-Aciers Inoxydables d’Usage Général-Demi-Produits, Barres et Fil Machine Superseded by: EN 10088-3:1995 Stainless Steels – Part 3: Technical Delivery Conditions for Semi-Finished Products, Bars, Rods and Sections for General Purposes Appendix 7 Former National Standards Superseded by CEN Standards 521 Handbook of Comparative World Steel Standards Chapter 9: Steels for Special Use Former National Standards Superseded by EN Standards Current EN Standard BSI BS 970-1:1991 Wrought Steels for Mechanical and Allied Engineering Purposes – Part 1: General Inspection and Testing Procedures and Specific Requirements for Carbon, Carbon Manganese, Alloy and Stainless Steels Superseded by: EN 10095:1999 Heat Resisting Steels and Nickel Alloys BSI BS 970-1:1991 Wrought Steels for Mechanical and Allied Engineering Purposes – Part 1: General Inspection and Testing Procedures and Specific Requirements for Carbon, Carbon Manganese, Alloy and Stainless Steels Partially Superseded by: EN 10084:1998 Case Hardening Steels – Technical Delivery Conditions EN 10085:2001 Nitriding Steel – Technical Delivery Conditions EN 10087:1999 Free Cutting Steels-Technical Delivery Conditions for Semi-Finished Products, Hot-Rolled Bars and Rods EN 10250-4:2000 Open Steel Die Forgings for General Engineering Purposes – Part 4: Stainless Steels BSI BS 970-2:1988 AMD 2:1992 Wrought Steels for Mechanical and Allied Engineering Purposes – Part 2: Requirements for Steels for the Manufacture of Hot Formed Springs (Withdrawn) Superseded by: EN 10089:2002 Hot Rolled Steels for Quenched and Tempered Springs – Technical Delivery Conditions. BSI BS 970-3:1991 Wrought Steel for Mechanical and Allied Engineering Purposes – Part 3: Bright Bars for General Engineering Purposes (Withdrawn) Superseded by: EN 10277 Bright Steel Products – Technical Delivery Conditions EN 10277-1:1999 General EN 10277-2:1999 Steels for General Engineering Purposes EN 10277-3:1999 Free-Cutting Steels EN 10277-4:1999 Case-Hardening Steels EN 10277-5:1999 Steels for Quenching and Tempering EN 10278:1999 Dimensions and Tolerances of Bright Steel Products BSI BS 1449-2:1983 Steel Plate, Sheet and Strip – Part 2: Specification for Stainless and Heat-Resisting Steel Plate, Sheet and Strip (Withdrawn) Superseded by: EN 10095:1999 Heat Resisting Steels and Nickel Alloys EN 10029:1991 Specification for Tolerances on Dimensions, Shape and Mass for Hot Rolled Steel Plates 3 Mm Thick or Above EN 10048:1997 Hot Rolled Narrow Steel Strip – Tolerances on Dimensions and Shape EN 10051:1992 Specification for Continuously Hot-Rolled Uncoated Plate, Sheet and Strip of Non-Alloy and Alloy Steels – Tolerances on Dimensions and Shape EN 10258:1997 Cold-Rolled Stainless Steel Narrow Strip and Cut Lengths – Tolerances on Dimensions and Shape EN 10259:1997 Cold-Rolled Stainless and Heat Resisting Steel Wide Strip and Plate/Sheet – Tolerances on Dimensions and Shape BSI BS 4659:1989 Tool and Die Steels (Withdrawn) Superseded by: EN ISO 4957:2000 Tool Steels [...]... Mécaniques Handbook of Comparative World Steel Standards EN ISO 4957:2000 Tool Steels Superseded by: EN 10277-3:1999 Bright Steel Products – Technical Delivery Conditions – Part 3: Free-Cutting Steels Appendix 8 ISO IRON AND STEEL PRODUCT STANDARDS Handbook of Comparative World Steel Standards Appendix 8 Designation ISO 9444:2002 ISO 9445:2002 ISO 11972:1998 ISO 11973:1999 ISO/TR 15510:2003 ISO 683 -14: 2004... other than welding Grade T(8) Forged steel lifting hooks with point and eye for use with steel chains of grade T(8) Forged steel lifting components for use with grade T(8) chain Handbook of Comparative World Steel Standards Appendix 9 ASTM A 941-03 TERMINOLOGY RELATING TO STEEL, STAINLESS STEEL, RELATED ALLOYS, AND FERROALLOYS Handbook of Comparative World Steel Standards An American National Standard... Stainless steels Chemical composition Heat-treatable steels, alloy steels and free-cutting steels Part 14: Hot-rolled steels for quenched and tempered springs Stainless steels for springs Part 1: Wire Stainless steels for springs Part 2: Strip Steel wire for mechanical springs Part 1: General requirements Steel wire for mechanical springs Part 2: Patented cold-drawn non-alloy steel wire Steel. .. drill steels in bar form, hexagonal and round Hot-rolled steel bars Part 1: Dimensions of round bars Hot-rolled steel bars Part 2: Dimensions of square bars Hot-rolled steel bars Part 3: Dimensions of flat bars Hot-rolled steel bars Part 4: Tolerances Hollow steel bars for machining High yield strength steel bars and sections Part 1: General delivery requirements High yield strength steel. .. Part 5: Austenitic steels Tool steels Tool steels and bearing steels Micrographic method for assessing the distribution of carbides using reference photomicrographs Cutting tools Designation of high-speed steel groups Heat-treatable steels, alloy steels and free-cutting steels Part 1: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products Heat-treatable steels,... sheet of structural quality Continuous hot-dip zinc-coated carbon steel sheet of structural quality Continuous hot-dip terne (lead alloy) coated cold-reduced carbon steel sheet of commercial drawing and structural qualities Continuous hot-dip aluminium/silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities Handbook of Comparative World Steel Standards 526 ISO Iron and Steel. .. non-alloy steel wire ropes and for large diameter steel wire ropes -Specifications Steel wire ropes for general purposes Minimum requirements Steel wire ropes Vocabulary Drawn wire for general purpose non-alloy steel wire ropes Terms of acceptance Steel wire ropes for general purposes Determination of actual breaking load Handbook of Comparative World Steel Standards Appendix 8 Designation ISO 3178:1988... Heat-treatable steels, alloy steels and free- cutting steels Part 18: Bright products of unalloyed and low alloy steels Hot-rolled carbon steel sheet of commercial and drawing qualities Cold-reduced carbon steel sheet of commercial and drawing qualities Continuous hot-dip zinc-coated carbon steel sheet of commercial, lock-forming and drawing qualities High yield strength flat steel products Part 1: General... Specification and approval of welding procedures for production welding of steel castings Visual examination of surface quality of steel castings Corrosion-resistant cast steels for general applications Heat-resistant cast steels and alloys for general applications Austenitic manganese steel castings Centrifugally cast steel and alloy products Part 1: General testing and tolerances Steel forgings and rolled... verification of hydraulic leak-tightness Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of longitudinal imperfections Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Eddy current testing for the detection of imperfections Handbook of Comparative World Steel Standards 528 . Conditions – Part 3: Free-Cutting Steels. Handbook of Comparative World Steel Standards Appendix 8 ISO IRON AND STEEL PRODUCT STANDARDS Appendix 8 ISO Iron and Steel Product Standards. CEN Standards Appendix 7 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards. by CEN Standards 515 Handbook of Comparative World Steel Standards Chapter 5: Steel Tubes and Pipes (Continued) Former National Standards Superseded by EN Standards Current EN Standards

Ngày đăng: 10/08/2014, 12:20

Từ khóa liên quan

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan