Tightening Torque Table Of Standard Parts (CHUNG) Bolt niminal diameter (mm) Pich (mm) Torque Nm (kg.cm, lb.ft) Head Mark 4 Head Mark 7 M5 0.8 3 ~ 4 (30 ~ 40, 2.2 ~ 2.9) 5 ~ 6 (50 ~ 60, 3.6 ~ 4.3) M6 1.0 5 ~ 6 (50 ~ 50, 3.6 ~ 4.3) 9 ~ 11 (90 ~ 110, 6.5 ~ 8.0) M8 1.25 12 ~ 15 (120 ~ 150, 9 ~ 11) 20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 ) M10 1.25 25 ~ 30 (250 ~ 300, 18 ~ 22) 30 ~ 50 (300 ~ 500, 22 ~ 36) M12 1.25 35 ~ 45 (350 ~ 450, 25 ~ 33) 60 ~ 80 (600 ~ 800, 43 ~ 58) M14 1.5 75 ~ 85 (750 ~ 850, 54 ~ 61) 120 ~ 140 (1,200 ~ 1,400, 85 ~ 100) M16 1.5 110 ~ 130 (1,100 ~ 1,300, 80 ~ 94) 180 ~ 210 (1,800 ~ 2,100, 130 ~ 150) M18 1.5 160 ~ 180 (1,600 ~ 1,800, 116 ~ 130) 260 ~ 300 (2,600 ~ 3,000, 190 ~ 215) M20 1.5 220 ~ 250 (2,200 ~ 2,500, 160 ~ 180) 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300) M22 1.5 290 ~ 330 (2,900 ~ 3,300, 210 ~ 240) 480 ~ 550 (4,800 ~ 5,500, 350 ~ 400) M24 1.5 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300) 610 ~ 700 (6,100 ~ 7,000, 440 ~ 505) 1. The torques shown in the table are standard values under the following conditions. • Nuts and bolts are made of galvanized steel bar. • Galvanized plain steel washers are inserted. • All nuts, bolts and plain washers are dry. 2. The torques shown in the table are not applicable. • When spring washers, toothed washers and the like are inserted. • If plastic parts are fastened. • If self-tapping screws or self-locking nuts are used. • If threads and surfaces are coated with oil. 3. Reduce the torque values to the indicated percentage of the standard value under the following conditions. • If spring washers are used : 85% • If threads and bearing surfaces are stained with oil : 85% * ĐỘNG CƠ Tightening Torques Item N.m kgf.m lb-ft Cylinder block Engine support bracket bolt 42.2 ~ 53.9 4.3 ~ 5.5 31.1 ~ 39.8 Rear oil seal case assembly bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Piston cooling oil jet bolt 8.8 ~ 12.7 0.9 ~ 1.3 6.5 ~ 9.4 Engine mounting Engine mounting insulator bolt and nut 63.7 ~ 83.4 6.5 ~ 8.5 47.0 ~ 61.5 Engine mounting bracket and engine mounting insulator fixing nut 78.5 ~ 107.9 8.0 ~ 11.0 57.9 ~ 79.6 Engine mounting bracket and engine support bracket fixing bolt and nut 63.7 ~ 83.4 6.5 ~ 8.5 47.0 ~ 61.5 Transaxle mounting bracket bolt and nut 63.7 ~ 83.4 6.5 ~ 8.5 47.0 ~ 61.5 Transaxle mounting bracket and transaxle support bracket fixing bolt 78.5 ~ 107.9 8.0 ~ 11.0 57.9 ~ 79.6 Front roll stopper mounting bracket bolt 49.0 ~ 63.7 5.0 ~ 6.5 36.2 ~ 47.0 Front roll stopper mounting bracket and front roll stopper insulator fixing bolt 78.5 ~ 107.9 8.0 ~ 11.0 57.9 ~ 79.6 Rear roll stopper mounting bracket bolt 49.0 ~ 63.7 5.0 ~ 6.5 36.2 ~ 47.0 Rear roll stopper mounting bracket and front roll stopper insulator fixing bolt 78.5 ~ 107.9 8.0 ~ 11.0 57.9 ~ 79.6 Sub frame bolt 137.3 ~ 156.9 14.0 ~ 16.0 101.3 ~ 115.7 Main moving system Connecting rod cap bolt 27.5~31.4 + 88°~92° 2.8~3.2 + 88°~92° 20.3~23.1 + 88°~92° Crankshaft main bearing cap bolt 49.0 + 120° 5.0 + 120° 36.2 + 120° Drive plate bolt 117.7 ~ 127.5 12.0 ~ 13.0 86.8 ~ 94.0 Flywheel bolt 117.7 ~ 127.5 12.0 ~ 13.0 86.8 ~ 94.0 Timing chain Drive belt idler bolt 42.2 ~ 53.9 4.3 ~ 5.5 31.1 ~ 39.8 Drive belt tensioner bolt 42.2 ~ 53.9 4.3 ~ 5.5 31.1 ~ 39.8 Fead system bracket assembly bolt (8X40) 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 Fead system bracket assembly bolt (8X25) 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 Fead system bracket assembly bolt (10X45) 42.2 ~ 53.9 4.3 ~ 5.5 31.1 ~ 39.8 Timing chain cover bolt (8X35) 19.6 ~ 24.5 2.0 ~ 2.5 14.5 ~ 18.1 Timing chain cover bolt (6X30) 7.8 ~ 11.8 0.8 ~ 1.2 5.8 ~ 8.7 Timing chain cover bolt (6X16) 7.8 ~ 11.8 0.8 ~ 1.2 5.8 ~ 8.7 Crankshaft damper pulley bolt 196.1 + 60° 20 + 60° 144.7 + 60° Camshaft chain sprocket bolt 14.7 ~ 19.6 1.5 ~ 2.0 10.8 ~ 14.5 High pressure pump chain sprocket nut 78.5 ~ 93.2 8.0 ~ 9.5 57.9 ~ 68.7 High pressure pump bolt 24.5 ~ 28.4 2.5 ~ 2.9 18.1 ~ 21.0 High pressure pump chain sprocket service plug 73.5 ~ 88.3 7.5 ~ 9.0 54.2 ~ 65.1 Timing chain "A" guide bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Timing chain "B" guide bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Timing chain "A" auto tensioner bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Timing chain "B" auto tensioner bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Timing chain "A","B" tensioner lever bolt 29.4 ~ 31.4 3.0 ~ 3.2 21.7 ~ 23.1 Cylinder head Cylinder head cover bolt 8.8 ~ 10.8 0.9 ~ 1.1 6.5 ~ 8.0 Camshaft bearing cap bolt 10.8 ~ 12.7 1.1 ~ 1.3 8.0 ~ 9.4 Cylinder head bolt 78.5 + 120° + 120° 8.0 + 120° + 120° 57.9 + 120° + 120° Cylinder head side bolt 30.4 ~ 34.3 3.1 ~ 3.5 22.4 ~ 25.3 Vacuum pump bolt 7.8 ~ 11.8 0.8 ~ 1.2 5.8 ~ 8.7 Cooling system Water pump pulley bolt 7.8 ~ 11.8 0.8 ~ 1.2 5.8 ~ 8.7 Water pump cover bolt 19.6 ~ 24.5 2.0 ~ 2.5 14.5 ~ 18.1 Water pump bolt 19.6 ~ 24.5 2.0 ~ 2.5 14.5 ~ 18.1 Water inlet pipe fixing bolt 19.6 ~ 24.5 2.0 ~ 2.5 14.5 ~ 18.1 Water outlet pipe fixing bolt 7.8 ~ 11.8 0.8 ~ 1.2 5.8 ~ 8.7 Engine coolant temperature sensor 29.4 ~ 39.2 3.0 ~ 4.0 21.7 ~ 28.9 Water inlet fitting bolt 16.7 ~ 22.6 1.7 ~ 2.3 12.3 ~ 16.6 Radiator upper cover bolt 8.8 ~ 10.8 0.9 ~ 1.1 6.5 ~ 8.0 Radiator upper bracket bolt 8.8 ~ 10.8 0.9 ~ 1.1 6.5 ~ 8.0 Lubrication system Oil filter&cooler assembly bolt 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 Oil cooler bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Oil filter drain bolt 9.8 1.0 7.2 Oil filter cap 32.4 ~ 38.2 3.3 ~3.9 23.9 ~ 28.2 Oil drain plug 34.3 ~ 44.1 3.5 ~ 4.5 25.3 ~ 32.5 Oil level gauge guide fixing bot 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Upper oil pan bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Upper oil pan and transaxle case fixing bolt 39.2 ~ 46.1 4.0 ~ 4.7 28.9 ~ 34.0 Lower oil pan bolt and nut 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Balance shaft & oil pump module bolt (8X82) 30.4 ~ 34.3 3.1 ~ 3.5 22.4 ~ 25.3 Balance shaft & oil pump module bolt (8X40) 19.6 ~ 23.5 2.0 ~ 2.4 14.5 ~ 17.4 Oil pressure switch 14.7 ~ 21.6 1.5 ~ 2.2 10.8 ~ 15.9 Oil level sensor 8.8 ~ 9.8 0.9 ~ 1.0 6.5 ~ 7.2 Intake and exhaust system Intake manifold bolt and nut 18.6 ~ 23.5 1.9 ~ 2.4 13.7 ~ 17.4 Exhaust manifold nut 39.2 ~ 44.1 4.0 ~ 4.5 28.9 ~ 32.5 Exhaust manifold heat protector bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 DPF(or WCC) converter assembly heat protector bolt 17.7 ~ 21.6 1.8 ~ 2.2 13.0 ~ 15.9 DPF(or WCC) converter assembly support bracket bolt 44.1 ~ 53.9 4.5 ~ 5.5 32.5 ~ 39.8 DPF(or WCC) converter assembly and turbocharger fixing nut 49.0 ~ 68.6 5.0 ~ 7.0 36.2 ~ 50.6 Turbocharger oil feed pipe upper bolt 11.8 ~ 17.7 1.2 ~ 1.8 8.7 ~ 13.0 Turbocharger oil feed pipe lower bolt 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 Turbocharger oil drain pipe bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Turbocharger oil drain pipe nut 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 Turbocharger assembly nut 49 ~ 68.6 5.0 ~ 7.0 36.2 ~ 50.6 Intake air control valve bolt and nut 8.8 ~ 10.8 0.9 ~ 1.1 6.5 ~ 8.0 EGR pipe assembly bolt (8X25) 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 EGR pipe assembly bolt (6X14) 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 EGR cooler bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 EGR cooler nut 19.6 ~ 26.5 2.0 ~ 2.7 14.5 ~ 19.5 EGR & thermostat housing assembly bolt 19.6 ~ 24.5 2.0 ~ 2.5 14.5 ~ 18.1 Intercooler bracket bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Intercooler pipe&hose fixing clamp 4.9 ~ 6.9 0.5 ~ 0.7 3.6 ~ 5.1 Intercooler pipe fixing bolt 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Air cleaner lower cover fixing bolt 7.8 ~ 9.8 0.8 ~ 1.0 5.8 ~ 7.2 Intake air hose fixing clamp 2.9 ~ 4.9 0.3 ~ 0.5 2.2 ~ 3.6 DPF(or WCC) converter assembly and front muffler fixing nut 39.2 ~ 58.8 4.0 ~ 6.0 28.9 ~ 43.4 Front muffler and center muffler fixing nut 39.2 ~ 58.8 4.0 ~ 6.0 28.9 ~ 43.4 Center muffler and main muffler fixing nut 39.2 ~ 58.8 4.0 ~ 6.0 28.9 ~ 43.4 Tightening Torques Engine Control System Items kgf.m N.m lb-ft ECM installation bolts 0.4 ~ 0.6 3.9 ~ 5.9 2.9 ~ 4.3 ECM bracket installation bolt 0.8 ~ 1.2 7.8 ~ 11.8 5.8 ~ 8.7 ECM bracket installation nut 0.4 ~ 0.6 3.9 ~ 5.9 2.9 ~ 4.3 Mass air flow sensor clamp installation screw 0.3 ~ 0.5 2.9 ~ 4.9 2.2 ~ 3.6 Mass air flow sensor installation bolts 0.4 ~ 0.6 3.9 ~ 5.9 2.9 ~ 4.3 Boost pressure sensor installation bolts 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 Intake Air Temperature Sensor (IATS) #2 installation 2.0 ~ 3.0 19.6 ~ 29.4 14.5 ~ 21.7 Engine coolant temperature sensor installation 2.0 ~ 4.0 19.6 ~ 39.2 14.5 ~ 28.9 Camshaft position sensor installation bolt 0.8 ~ 1.2 7.8 ~ 11.8 5.8 ~ 8.7 Lambda sensor installation 4.1 ~ 6.1 40.2 ~ 59.8 29.7 ~ 44.1 DPF Differential Pressure Sensor installation bolt 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 DPF Differential Pressure Sensor bracket installation bolt 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 Exhuast Gas Temperature Sensor (EGTS) installation 4.0 ~ 5.0 39.2 ~ 49.1 28.9 ~ 36.2 Electric EGR control valve installation bolt 0.8 ~ 1.2 7.8 ~ 11.8 5.8 ~ 8.7 Variable swirl actuator installation bolt 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 Air control valve installation bolt 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 EGR Cooler Bypass Solenoid Valve installation bolt 0.8 ~ 1.2 7.8 ~ 11.8 5.8 ~ 8.7 Glower control module installation bolt 0.8 ~ 1.2 7.8 ~ 11.8 5.8 ~ 8.7 Glow plug installation 1.5 ~ 2.0 14.7 ~ 19.6 10.9 ~ 14.5 DPF assembly installation bolt 4.5 ~ 5.5 44.1 ~ 54.0 32.6 ~ 39.8 DPF assembly installation nut 5.0 ~ 7.0 49.1 ~ 68.7 36.2 ~ 50.6 DPF assembly stay installation bolt 4.5 ~ 5.5 44.1 ~ 54.0 32.6 ~ 39.8 Fuel Delivery System Items kgf.m N.m lb-ft Fuel tank band installation nut 4.0 ~ 5.5 39.2 ~ 54.0 28.9 ~ 39.8 Accelerator pedal module installation nut 1.7 ~ 2.6 16.7 ~ 25.5 12.3 ~ 18.8 Accelerator pedal installation bolt 0.9 ~ 1.4 8.8 ~ 13.7 6.5 ~ 10.1 Fuel pump plate cover installation 6.0 ~ 7.0 58.9 ~ 68.7 43.4 ~ 50.6 Fuel sender plate cover installation 6.0 ~ 7.0 58.9 ~ 68.7 43.4 ~ 50.6 Fuel filter installation nut 1.0 ~ 1.3 9.8 ~ 12.8 7.2 ~ 9.4 Fuel filter bracket installation nut 1.0 ~ 1.3 9.8 ~ 12.8 7.2 ~ 9.4 Injector clamp installation bolt 3.0 ~ 3.4 29.4 ~ 33.4 21.7 ~ 24.6 High pressure fuel pump installation bolt 2.5 ~ 3.1 24.5 ~ 30.4 18.1 ~ 22.4 Service plug washer installation 7.5 ~ 9.0 73.6 ~ 88.3 54.3 ~ 65.1 Common rail installation bolt 2.0 ~ 2.7 19.6 ~ 26.5 14.5 ~ 19.5 Common rail banjo installation bolt 1.8 ~ 2.8 17.7 ~ 27.5 13.0 ~ 20.3 High pressure fuel pipe installation nut (High pressure fuel pump ↔ Common Rail) 2.5 ~ 2.9 24.5 ~ 28.4 18.1 ~ 21.0 High pressure fuel pipe installation nut (Common Rail ↔ Injector) 2.5 ~ 2.9 24.5 ~ 28.4 18.1 ~ 21.0 High pressure fuel pipe clamp installation bolt 1.0 ~ 1.2 9.8 ~ 11.8 7.2 ~ 8.7 * Ly hop Tightening Torques Item N.m kgf.m lb-ft Clutch pedal installation bolt (to the pedal support member) 16.7~25.5 1.7~2.6 12.3~18.8 Clutch pedal installation nut (to the master cylinder) 5.9~7.8 0.6~0.8 4.3~5.8 Clutch tube flare nut 12.8~16.7 1.3~1.7 9.4~12.4 Clutch tube bracket installation bolt 7.8~9.8 0.8~1.0 5.8~7.24 Clutch release cylinder installation bolt 14.7~21.6 1.5~2.2 10.9~16.0 Clutch release cylinder union bolt 24.5~34.3 2.5~3.5 18.1~25.5 Clutch cover assembly installation bolt(9ea) 14.7~21.6 1.5~2.2 10.9~16.0 Ignition lock switch nut 7.8~9.8 0.8~1.0 5.8~7.3 * HS co khi Specifications Engine type R2.2 Manual transaxle type M6LF1 Gear ratio 1st 3.538 2nd 1.909 3rd 1.179 4th 0.814 5th 0.737 6th 0.628 Reverse 3.910 Final gear ratio 1st(1,2,3,4)/2nd(5,6,R) 4.538/3.933 Tightening Torques Item N.m kgf.m lb-ft Oil drain plug 58.9~78.5 6.0~8.0 43.4~57.9 Oil filler plug 58.9~78.5 6.0~8.0 43.4~57.9 Shift lever assembly 8.8~13.7 0.9~1.4 6.5~10.1 Transaxle mounting bracket bolt 66.7~78.5 6.8~8.0 49.2~57.9 Starter motor mounting bolt 49.1~63.8 5.0~6.5 36.2~47 Transaxle upper mounting bolt 42.2~54 4.3~5.5 31.1~39.8 Transaxle lower mounting bolt 42.2~54 4.3~5.5 31.1~39.8 * HS TỰ ĐỘNG Specifications Item Specification Transmission type A6LF3 Engine model Diesel 2.2 Torque converter type 3-element, 1-stage, 2-phase type Torque converter size Ø236 mm Oil pump system Parachoid Friction elements Clutch: 2EA Brake: 3EA OWC : 1EA Planetary gear 3EA Gear ratio 1st 4.651 2nd 2.831 3rd 1.842 4th 1.386 5th 1.000 6th 0.772 Reverse 3.393 Final gear ratio 3.195 Fluid pressure balance piston 3EA Accumulator 4EA Solenoid valve 8EA (VFS:6EA, ON/OFF:2EA) Shift lever position 4 Range (P,R,N,D) Oil filter 1EA VFS: Variable Force Solenoid Tightening Torques Item N.m Kgf.m lb-ft TCM installation nut 3.9 ~ 5.9 0.4 ~ 0.6 2.9 ~4.3 Shift cable bracket 14.7 ~ 21.6 1.5 ~ 2.2 10.9 ~ 15.9 Input shaft speed sensor 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Output shaft speed sensor 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Manual control lever 17.7 ~ 24.5 1.8 ~ 2.5 13.0 ~ 18.1 Inhibitor switch 13 ~ 15 1.3 ~ 1.5 9.4 ~ 10.9 Valve body cover 9.8 ~ 11.8 1.0 ~ 1.2 7.2 ~ 8.7 Oil level plug 34.3 ~ 44.1 3.5 ~ 4.5 25.3 ~ 32.6 Torque converter mounting bolt 45.1 ~ 52.0 4.6 ~ 5.3 33.3 ~38.3 Auto transaxle upper mounting bracket bolt 42.2 ~ 54.0 4.3 ~ 5.5 31.3 ~ 39.8 Auto transaxle suppor bracket bolt 78.5 ~ 107.9 8.0 ~ 11.0 57.9 ~ 79.6 • drieshaft and axle SPECIFICATION Items Inner side Outer side Front driveshaft Diesel 2.2 M/T 2WD/4WD, Diesel 2.2 A/T 2WD/4WD, Gasoline 2.7 A/T 2WD Joint type PTJ BJ Max. permissible angle 21° 46° Gasoline 2.7 A/T 4WD, Gasoline 2.7 M/T 2WD/4WD Joint type SFJ BJ Max. permissible angle 21° 46° Rear driveshaft Joint type DOJ BJ Max. permissible angle 22° 46° Differential 　 Oil type Hypoid gear oil (API GL-5, SAE 75W/90) Oil capacity (L) About 0.9 Reduction gear type Hypoid gear [...]... Service Standard Items Brake pedal height Standard vale 214 mm (8.43 in) Brake pedal stroke 122 mm (4.8 in) Stop lamp clearance 1 ~ 2 mm (0.04 ~ 0.08 in) Brake pedal free play 3 ~ 8 mm (0.12 ~ 0.31 in) Front brake disc thickness 28 mm (1.10 in) Front brake disc pad thickness 10.5 mm (0.41 in) Rear brake disc thickness 11 mm (0.43 in) Rear brake disc pad thickness 10 mm (0.39 in) Tightening Torque Items... Final drive gear backlash mm(in.) 0.10 ~ 0.15 (0.0039 ~ 0.0059) Differential gear backlash mm(in.) 0 ~ 0.05 (0 ~ 0.0020) BJ : Birfield Joint DOJ : Double Offset Joint PTJ : Pillow journal Tri-pot Joint SFJ : Shudderless Free-ring Joint TIGHTENING TORQUE 　 Items lb-ft 88.3~107.9 9~11 65.1~79.6 Driveshaft castle nut 196.1~255.0 20~26 144.7~188.1 Strut assembly lower mounting bolt 152.0~171.6 15.5~17.5... pump Gasoline 2.7L Gasoline 3.3L Vane Relief pressure 100 ~ 105 kgf/cm² Discharge 8.5 cc/rev Relief pressure 95 ~ 100 kgf/cm² Discharge 9.6 cc/rev Relief pressure 98 ~ 105kgf/cm² Discharge 9.4cc/rev Tightening Torque Items Nm kgf.m lb-ft Hub nut 90 ~ 110 9.0 ~ 10.0 65 ~ 72 Steering wheel lock nut 40 ~ 50 4.0 ~ 5.0 29 ~ 36 Steering column mounting bolts and nut 13 ~ 18 1.3 ~ 1.8 9.4 ~ 13.0 4~6 0.4 ~ 0.6... Specification Item Resistance (Ω) Driver Airbag (DAB) 1.4 ~ 6.2 Passenger Airbag (PAB) 1.4 ~ 6.2 Side Airbag (SAB) 1.4 ~ 6.2 Curtain Airbag (CAB) 1.4 ~ 6.2 Seat Belt Retractor Pretensioner (BPT) 1.4 ~ 6.2 Tightening Torques Item Driver Airbag (DAB) Passenger Airbag (PAB) kgf·m Nm lb-ft 0.8 ~ 1.1 7.9 ~ 10.8 5.8 ~ 8.0 Bolt : 1.9 ~ 2.7 18.6 ~ 26.5 13.7 ~ 19.5 Nut : 0.9 ~ 1.4 8.8 ~ 13.7 6.5 ~ 10.1 Curtain Airbag... Wheel Alignment Items Front Rear Camber -0.5° ± 0.5° -1° ± 0.5° Caster 4.33° ± 0.5° - Toe-in 0° ± 0.2°(0.079) 0.2°(0.079) ± 0.2°(0.079) King pin angle 12.98° ± 0.5° - Tread mm 1615(63,58) 1619(63,58) Tightening torque Front Suspension Items Nm Kgf.m lb-ft Front wheel nut 88.3 ~ 107.9 9 ~ 11 65.1 ~ 79.6 Front strut assembly mounting nut (to body) 44.1 ~ 58.8 4.5 ~ 6.0 32.5 ~ 43.4 152.0 ~ 171.6 15.5 ~ 17.5... Thickness Front door glass 3.5mm Rear door glass 3.5mm Front 3 point type with Emergency Locking Retractor (E.L.R) Rear 3 point type with Emergency Locking Retractor (E.L.R) Rear Door Seat Belts Tightening Torque Items Front and rear doors Tail gate N.m Kgf.m lbf.ft Door hinge to body 21.6~26.5 2.2~2.7 15.9~19.5 Door hinge to door 21.6~26.5 2.2~2.7 15.9~19.5 Tail gate hing to body 21.6~26.5 2.2~2.7... Solid disc Disc O.D 302 mm (11.89 in) Caliper piston Rear brake Double Single Type DIH (Drum in hat) Drum I.D 190 mm (7.48 in) DOT 3 O.D : Outer Diameter I.D : Inner Diameter Specification (ABS) Part Item Standard value System 4 channel 4 sensor (Solenoid) Type Motor, valve relay intergrated type Operating voltage 10 V ~ 16 V(DC) Operating temperature HECU(Hydraulic and Electronic Control Unit) Remark -40... current High 11.8 ~ 16.8 mA Typ.14 mA Frequency range 1 ~ 2500 HZ Front 0.4 ~ 1.0 mm Typ.0.7 mm Rear Air gap 0.15 ~ 1.5 mm Typ.0.7 mm Tone wheel 48 teeth Output duty 30~70 % Specification (ESP) Part Item Standard Value Remark System Operating voltage 10 V ~ 16 V(DC) -40 ~ 120 °C(-40 ~ 248 °F) Operating voltage 12 V Current consumption 80 mA DC 4.5 ~ 20V Operating temperature -40 ~ 150 °C Output current . Tightening Torque Table Of Standard Parts (CHUNG) Bolt niminal diameter (mm) Pich (mm) Torque Nm (kg.cm, lb.ft) Head Mark 4 Head Mark 7 M5. 610 ~ 700 (6,100 ~ 7,000, 440 ~ 505) 1. The torques shown in the table are standard values under the following conditions. • Nuts and bolts are made of galvanized steel bar. • Galvanized plain. and plain washers are dry. 2. The torques shown in the table are not applicable. • When spring washers, toothed washers and the like are inserted. • If plastic parts are fastened. • If self-tapping