Thermodynamics Interaction Studies Solids, Liquids and Gases Part 8 pptx

60 344 0
Thermodynamics Interaction Studies Solids, Liquids and Gases Part 8 pptx

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

ThermodynamicsInteraction StudiesSolids, Liquids and Gases 410 Fig. 1. Equilibrium gaseous composition in M-F systems at total pressure of 2 kPa [7]. Thermodynamic Aspects of CVD Crystallization of Refractory Metals and Their Alloys 411 Fig. 2. Equilibrium gaseous composition in M-F-H systems at total pressure of 2 kPa and hydrogen to highest fluoride initial ratio of 10 [31]. ThermodynamicsInteraction StudiesSolids, Liquids and Gases 412 Fig. 3. Yield of metals (V, Nb, Ta, Mo, W, Re) from the equilibrium mixtures of their fluorides with hydrogen (1:10) as a function of the temperature [31]. 5. Equilibrium composition of solid deposit in W-M-F-H systems A thermodynamics of alloy co-deposition is often considered as a heterogeneous equilibrium of gas and solid phases, in which solid components are not bonded chemically or form the solid solution. The calculation of the solid solution composition requires the knowledge of the entropy and enthalpy of the components mixing. The entropy of mixing is easily calculated but the enthalpy of mixing is usually determined by the experimental procedure. For tungsten alloys, these parameters are estimated only theoretically [34]. A partial enthalpy of mixing can be approximated as the following: Δ Н m = (h 1,i + h 2,i T + h 3,i x i ) × (1 - x i ) 2 , where h 1,i , h 2,i , h 3,i – polynomial’s coefficients, T – temperature, x i - mole fraction of solution component. The surface properties of tungsten are sharply different from the bulk properties due to strongest chemical interatomic bonds. Therefore, there is an expedience to include the crystallization stage in the thermodynamic consideration, because the crystallization stage controls the tungsten growth in a large interval of deposition conditions. To determine the enthalpy of mixing of surface atoms we use the results of the desorption of transition metals on (100) tungsten plane presented at the Fig. 4. [35]. The crystallization energy can be determined as the difference between the molar enthalpy of the transition metal sublimation Thermodynamic Aspects of CVD Crystallization of Refractory Metals and Their Alloys 413 from (100) tungsten surface and sublimation energy of pure metal. These values are presented in the table 4 in terms of polynomial’s coefficients, which were estimated in the case of the infinite dilute solution. The peculiarity of the detail calculation of polynomial’s coefficients is discussed in [7]. The data predict that the co- crystallization of tungsten with Nb, V, Mo, Re will be performed more easily than the crystallization of pure tungsten. The crystallization of W-Ta alloys has the reverse tendency. Certainly the synergetic effects will influence on the composition of gas and solid phases. № М ∆H 0 m ּ ◌ 298 К x i = 0 h 1 , i kJ/mol h 2 , i kJ/mol h 3 , i kJ/mol x i 1 W 0 0 0 0 1,0000-0,9375 Ta 36,4±10,9 36,4 -0,00042 72,7 0,0000-0,0625 2 W 0 0 0 0 1,0000-0,9375 Nb -225,7±50,2 -225,7 -0,00025 -451,4 0,0000-0,0625 3 W 0 0 0 0 1,0000-0,9375 V -434,7±50,2 -434,7 -0,00017 -1304,2 0,0000-0,0625 4 W 0 0 0 0 1,0000-0,9375 Mo -467,7±10,9 -467,7 -0,00117 -935,5 0,0000-0,0625 5 W 0 0 0 0 1,0000-0,9375 Re -220,3±10,9 -220,3 -0,00058 -440,5 0,0000-0,0625 Table 4. Excess partial “enthalpy of mixing” atoms for crystallization of W-M binary solid solution and h i polynomial’s coefficients for x i = 0 – 0.0625 and T = 298 – 2500 K [7, 31]. Therefore the thermodynamic calculation for gas and solid composition of W-M-F-H systems were carried out for following cases: 1. without the mutual interaction of solid components; 2. for the formation of ideal solid solution 3. for the interaction of binary solution components on the surface. The temperature influence on the conversion of VB group metal fluorides and their addition to the tungsten hexafluoride – hydrogen mixture is presented at the Fig.5 a,b,c. If the metal interaction in the solid phase is not taken into account, the vanadium pentafluoride is reduced by hydrogen only to lower-valent fluorides. It should be noted that metallic vanadium can be deposited at temperatures above 1700 K. Equilibrium fraction of NbF 5 conversion achieves 50% at 1400 K, and of TaF 5 – at 1600 K (Fig. 5 a,b,c, curves 1). The thermodynamic consideration of ideal solid solution shows that tungsten-vanadium alloys may deposit at the high temperature range (T ≥ 1400 K) and metallic vanadium is deposited in mixture with lower-valent fluorides of vanadium (Fig. 5 a, curves 2). The beginnings of formation of W-Nb and W-Ta ideal solid solutions are shifted to lower temperature by about 100 K (Fig. 5 b,c, curves 2) in comparison with the case (1). ThermodynamicsInteraction StudiesSolids, Liquids and Gases 414 Fig. 4. Partial molar enthalpy of 4d и 5d atoms sublimation ( s H ) from tungsten plane (100) and atomization energy (Ω) of transition metals in dependence on their place in periodic table [35] Thermodynamic Aspects of CVD Crystallization of Refractory Metals and Their Alloys 415 a) V k*VF 2 k*VF 3 b) Nb c) Ta Fig. 5. Equilibrium yield of VB metals during crystallization with tungsten at initial ratio WF6:MF5:H2=10, total pressure of 2 kPa calculated for following cases: 1. without the mutual interaction of solid components; 2. for the formation of ideal solid solution 3. for the interaction of binary solution components on the surface. Fig. 6. Temperature influence on equilibrium yield of tungsten in W-Re-F-H (1) and W-F-H (2) systems at total pressure of 2 kPa and gaseous composition of (WF 6 +6% ReF 6 ) : H 2 = 10 Taking into account the interaction of component of alloys during crystallization, the formation of W-V and W-Nb alloys possibly takes place at the temperatures above 300 K ThermodynamicsInteraction StudiesSolids, Liquids and Gases 416 (Fig. 5 a,b, curves 3). Temperature boundary shown at the Fig. 5 is shifted in reverse direction for the W-Ta system (Fig. 5 c, curves 3). It should be noted, that the calculation results performed for cases (2) and (3) (for ideal and nonideal solid solution) for the W-Ta system are almost identical due to the small enthalpy of mixing [35]. The influence of rhenium and molibdenium on the equilibrium yield of tungsten in the M- W-F-H systems is observed for W-Re and W-Mo alloys deposition. The ReF 6 addition to the gas mixture with WF 6 increase insignificantly the yield of tungsten in spite of strong atom interaction during the crystallization according to thermodynamic calculations (Fig. 6). This effect is still smaller for the case of W-Mo co-deposition. However equilibrium yield of metals for their co-deposition with tungsten and the energy of the interaction of metallic components during the crystallization have the common tendency. The knowledge of refined data of process energies will allow us to obtain a more realistic situation. 6. The application fields of the coatings The thermodynamic background presented above is very useful for production of the coatings based on tungsten, tungsten alloys with Re, Mo, Nb, Ta, V and tungsten compounds (for example tungsten carbides). The tungsten coatings have found wide application in thin-film integral circuits when preparing the Ohmic contacts in the production of the silicon-, germanium-, and gallium-arsenide-based Schottky-barrier diodes. The tungsten selective deposition technology is perspective in the production of conducting elements at dielectric substrates [36]. Tungsten films are used for covering hot cathodes, improving their emission characteristics, and as protective coatings for anodes in extra-high- power microwave devices. The CVD-tungsten coatings are used as independent elements in electronics. The X-ray bremsstrahlung in modern clinical tomographs and other X-ray units is obtained by using tungsten or W–Re coatings at rotating anodes made of molybdenium or carbon– carbon composite materials. In the nuclear power engineering, tungsten was shown to be a good material for enveloping nuclear fuel particles because of low diffusion permeability of the envelope for the fuel. The tungsten- and W–Re alloy-coatings [2, 3, 5] are extremely stable in molten salts and metals used as coolants in high-temperature and nuclear machinery, e.g., in heat pipes with lithium coolant and in thermonuclear facilities. Tungsten emitters with high emission uniformity, elevated high-temperature grain orientation and microstructure stability are of interest for their use in thermionic energy converters. High-temperature technical equipment cannot go without tungsten crucibles, capillaries, and other works that can be easily prepared by the CVD techniques. Tungsten is used as a coating for components of jet engines, fuel cell electrodes, filters and porous components of ion engines, etc. [2] The CVD-alloying of tungsten coatings with rhenium allows to improve significantly their operating ability, especially under the temperature or load cycling. Tungsten compounds have a wide field of application. The tungsten-carbide composites deposited by using the fluoride technology occupy a niche among coatings with a thickness of 10 to 100 mkm; they are unique in respect of strengthening practically any material, starting with carbon, tool, and stainless steels, titanium alloys, and finishing with hard alloys. CVD method permits to coat complicated shape components (which cannot be coated using PVD-method or plasma sputtering of carbide powders with binder). Below we list the most promissing fields of applications [37]. In the first place we can mention the strengthening of the oil and gas and drilling equipment (pumps, friction and erosion assemblies). The problems of hydrogen- sulfide corrosion, Thermodynamic Aspects of CVD Crystallization of Refractory Metals and Their Alloys 417 wear of movable units, and erosion of immobile parts of drilling bits operating underground take special significance because their replacement is very expensive. The carbide coatings can be deposited inside cylinders and on the outer surfaces of components of rotary or piston oil pumps. Numerous units in the oil and gas equipment, for example, block bearings, solution-supplying channels in drilling bits, backings directing the sludge flow, etc. require the strengthening of their working surfaces. Another application in this field is the coating of metal–metal gaskets in the high- and ultrahigh-pressure stop and control valves. In addition to intense corrosion, abrasion and erosion wear, the working surfaces of ball cocks and dampers are subject of seizing under high pressure; W–C-coatings prevent the seizure. An important advantage of the carbide coatings is their accessibility for the quality of surface polishing, due to the initial smooth morphology. The examples mentioned above relate not only to oil and gas but also to chemical industry. The W–C-coatings are promising for working in contact with hydrogen- sulfide-rich oil, acids, molten metals, as well as chemically aggressive gases. Due to their high wear and corrosion resistance, these coatings can be use instead of hard chromium. The abrasion mass extrusion and the metal shape draft require expensive extrusion tools; the product price depends on the working surface quality and life time. The extrusion tools must often have sophisticated shape inappropriate for coating with PVD or PACVD methods. Therefore, W–C-coating prepared by a thermal CVD-method is promising in strengthening these tools. Strengthening of spinneret for drawing wires or complicated section of steel, copper, matrices for aluminum extrusion, ceramic honeycomb structures for the porous substrate of catalytic carriers may give the same effect. Also, very perspective is the deposition of strengthening coatings onto components of equipment for the pressing of powdered abrasion materials. One may also mention the strengthening of knife blade used for cutting paper, cardboard, leather, polyethylene, wood, etc [38]. In addition to the surface strengthening, the W–C-coatings can function as high-temperature glue for mounting diamond particles in a matrix when preparing diamond tools or diamond cakes (conglomerates) in drilling bits [39]. The above-given examples demonstrate the variety of applications for tungsten, its alloys and carbides in mechanical engineering, chemical, gas and oil industry, metallurgy, and microelectronics. 7. Conclusion 1. A number of unknown thermochemical constants of refractory metal fluorides were calculated and collected in this chapter. 2. The systematic investigation of equilibrium states in the M-F, M-F-H (M = V, Nb, Ta, Mo, W, Re) systems was carried out. It was demostrated that the equiblibrium concentrations of highest fluorides in the M-F systems are determined by the place of metal in the periodic table. They rise with the increase of atomic number within each group and decrease with the increase of atomic number within each period. The low valent fluoride concentrations have the opposite tendency. It was shown that the equilibrium yield of Re, Mo, W deposition from the M-F-H systems achieve 100% at room temperature, equilibrium yield of Nb, Ta and V deposition - at temperatures above 1300 K, 1600 K and 1700 K, respectively. 3. The solid compositions of the W-M-F-H systems were calculated by taking into account the formation of ideal, nonideal solid solution, the mechanical mixture of solid ThermodynamicsInteraction StudiesSolids, Liquids and Gases 418 components and the atom intraction on the growing surface during the crystallization. It was established that only an introduction in the thermodynamic calculation of atom interaction on the growing surface, which increase in the following sequence: Ta, W, Re, Nb, V, Mo, results in a rise of yield of VB group metals under their co-deposition with tungsten, excepting W-Ta system. This may explain the experimentally observed tungsten yield rise under its alloying with rhenium and molibdenium. 4. The thermodynamic analysis, performed by taking into account the formation of solid lower-valent fluorides and excess enthalpy of atom interaction during crystallization, showed that the moving force of CVD of the alloys from the W-M-F-H systems (the supersaturation in these systems) increase in order: Ta, Nb, V, Mo, W, Re. 5. A lot of applications of tungsten coatings, deposited from tungsten hexafluoride and hydrogen mixture at low temperature, as well as tungsten alloys and carbides are reviewed in this chapter. 8. Acknowledgments This work was supported by the Russian Foundation for Basic Research, project No. 09-08- 182. 9. Appendix 1 Description of symbols used in the text Symbol Description Ω Atomization energy М Metal Х Halid n Valency of metal Δ f Н Formation enthalpy at Atom φ Function Z m Atomic number of metal Z x Atomic number of halid ψ Functional Δ s Н Sublimation enthalpy S Entropy Δ f Н о 298 (g) Standart formation enthalpy at 298 K at gaseous state Δ f Н о (s) Standart formation enthalpy at 298 K at solid state Δs H о 298 Standart sublimation enthalpy at 298 K S о 298 (g) Standart entropy at 298 K at gaseous state S о 298 (s) Standart entropy at 298 K at solid state С р Specific heat at constant stress Δ Н m Partial enthalpy of mixing s Δ H Partial molar enthalpy ∆H 0 m Standart mixing enthalpy [...]... 1 283 .751 1. 288 361.094 10 08. 281 1.3 98 1166.650 1170. 280 1.325 2777.761 1 287 .224 1. 287 388 .87 2 1011.923 1.396 1222.205 11 78. 509 1.322 288 8 .87 2 1290.721 1. 286 416.650 1015.603 1.394 1277.761 1 186 .89 3 1.319 2999. 983 1294.242 1. 285 444.427 1019.320 1.392 1333.316 1192.570 1.317 3111.094 1297. 789 1. 284 499. 983 10 28. 781 1. 387 1444.427 1204.142 1.313 3222.205 1301.360 1. 283 555.5 38 1054.563 1.374 1555.5 38. .. K T0=2500 K T0=3000 K T0=3500 K P* P0 * 0 a* a0 m A* ρ0 a0 0 .83 26 0 .83 28 0 .83 66 0 .85 35 0 .86 89 0 .87 22 0 .87 43 0 .87 58 0.5279 0.5279 0.5293 0.5369 0.54 48 0.5466 0.5475 0.5 484 0.6340 0.6339 0.6326 0.6291 0.6270 0.6266 0.6263 0.6262 0.9124 0.9131 0.9171 0.9 280 0.9343 0.9355 0.9365 0.9366 0.5 785 0.5 788 0. 580 2 0. 583 8 0. 585 8 0. 586 2 0. 586 5 0. 586 5 Table 3 Numerical values of the critical parameters at high... 1304.957 1. 282 611.094 1054.563 1.370 1666.650 1225.121 1.306 3444.427 1304.957 1. 282 666.650 1067.077 1.3 68 1777.761 1234.409 1.303 3555.5 38 13 08. 580 1. 281 722.205 1 080 .005 1.362 188 8 .87 2 1243 .88 3 1.300 777.761 1093.370 1.356 1999. 983 1250.305 1.2 98 Table 1 Variation of CP(T) and γ(T) versus the temperature for air For a perfect gas, the γ and CP values are equal to γ=1.402 and CP=1001. 289 32 J/(kgK)... (γ=1.402) T0=2 98. 15 K T0=500 K T0=1000 K T0=1500 K T0=2000 K T0=2500 K T0=3000 K T0=3500 K 1.20 78 1.20 78 1.2076 1.2072 1.2062 1.20 48 1.2042 1.20 38 1.2033 1.4519 1.45 18 1.4519 1.4613 1.47 48 1. 483 2 1. 487 9 1.4912 1.4936 1. 580 2 1. 580 0 1. 580 2 1.5919 1.6123 1.6 288 1.6401 1.6479 1.6533 1.6523 1.6521 1.6523 1.6646 1. 687 1 1.7069 1.7221 1.7337 1.7422 1.6959 1.6957 1.69 58 1.7 085 1.7317 1.7527 1.7694 1. 782 8 1.7932 Table... T0=2 98. 15 K T0=500 K T0=1000 K T0=1500 K T0=2000 K T0=2500 K T0=3000 K T0=3500 K 1. 685 9 1. 685 9 1.6916 1.7295 1.7 582 1.7711 1.7795 1. 785 1 1. 788 9 4.2200 4.2195 4.2373 4.4739 4. 782 2 4.9930 5.1217 5.2091 5.2727 10.6470 10.6444 10. 689 5 11.3996 12.6397 13 .86 17 14 .82 27 15.5040 16.00 98 24.7491 24.7401 24 .84 47 26.5019 29.7769 33. 586 0 37.2104 40. 384 4 43.0001 52.4769 52.4516 52.6735 56. 188 7 63.2133 72.0795 81 .2941... 55.5 38 1001.104 1.402 83 3.316 1107.192 1.350 2111.094 1256 .81 3 1.296 T (K) CP J/(Kg K) γ(T) 88 8 .87 2 1119.0 78 1.345 2222.205 1263.410 1.294 222.205 1001.101 1.402 944.427 1131.314 1.340 2333.316 1270.097 1.292 277.761 1002 .88 5 1.401 999. 983 1141.365 1.336 2444.427 1273.476 1.291 305.5 38 1004.675 1.400 1055.5 38 1151.6 58 1.332 2555.5 38 1276 .87 7 1.290 333.316 1006.473 1.399 1111.094 1162.202 1.3 28 2666.650...  T (a8  T (a9  T (a10 ))))))))) The interpolation (ai i=1, 2, …, 10) of constants are illustrated in table 2 I ai I ai 1 1001.10 58 6 3.069773 10-12 2 0.040661 28 7 -1.350935 10-15 3 -0.000633769 8 3.472262 10-19 4 2.747475 10-6 9 -4 .84 6753 10-23 5 10-9 10 2 .84 1 187 10-27 -4.03 384 5 Table 2 Coefficients of the polynomial CP(T) (23) 426 ThermodynamicsInteraction StudiesSolids, Liquids and Gases. .. 5.0000 6.0000 MS (T0=2 98. 15 K) 1.4995 1.9995 2.9995 3.9993 4.9 989 5.9 985 MS (T0=500 K) 1.4977 1.9959 2.9956 3.9955 4.9951 5.9947 MS (T0=1000 K) 1. 487 9 1.9705 2.93 98 3.9237 4.9145 5.9040 MS (T0=1500 K) 1. 483 0 1.9534 2 .87 77 3 .81 47 4.7727 5.7411 MS (T0=2000 K) 1. 480 7 1.9463 2 .84 32 3.7293 4.6372 5.5675 MS (T0=2500 K) 1.4792 1.9417 2 .82 45 3.6765 4.5360 5.4209 MS (T0=3000 K) 1.4 785 1.9 388 2 .81 21 3.6454 4.4676... 0.3560 0.2371 0.1659 0.1214 T0=2 98. 15 K 0.5544 0.3560 0.2372 0.1659 0.1214 T0=500 K 0.5577 0.3 581 0.2 386 0.1669 0.1221 T0=1000 K 0. 581 0 0.3731 0.2 481 0.1736 0.1269 T0=1500 K 0.6031 0.3911 0.2594 0. 181 0 0.1323 T0=2000 K 0.6163 0.40 58 0.2694 0. 187 3 0.1366 T0=2500 K 0.6245 0.4162 0.27 78 0.19 28 0.1403 T0=3000 K 0.6301 0.4233 0. 284 8 0.1977 0.1473 T0=3500 K 0.6340 0.4 285 0.2901 0.20 18 0.1462 Table 4 Numerical... are presented in the table 9 90 80 1 70 2 60 50 40 3 30 4 20 10 0 1 2 3 4 5 6 Mach number Fig 14 Variation of the critical cross-section area ratio versus Mach number 4 38 ThermodynamicsInteraction StudiesSolids, Liquids and Gases a/a0 M=2.00 M=3.00 M=4.00 M=5.00 M=6.00 PG (γ=1.402) 0.7445 0.5966 0. 487 0 0.4074 0.3 484 T0=2 98. 15 K 0.7450 0.5970 0. 487 3 0.4076 0.3 486 T0=500 K 0.7510 0.6019 0.4913 . 1. 288 361.094 10 08. 281 1.3 98 1166.650 1170. 280 1.325 2777.761 1 287 .224 1. 287 388 .87 2 1011.923 1.396 1222.205 11 78. 509 1.322 288 8 .87 2 1290.721 1. 286 416.650 1015.603 1.394 1277.761 1 186 .89 3. 722.205 1 080 .005 1.362 188 8 .87 2 1243 .88 3 1.300 777.761 1093.370 1.356 1999. 983 1250.305 1.2 98 Table 1. Variation of C P (T) and γ(T) versus the temperature for air. For a perfect gas, the γ and. 1.319 2999. 983 1294.242 1. 285 444.427 1019.320 1.392 1333.316 1192.570 1.317 3111.094 1297. 789 1. 284 499. 983 10 28. 781 1. 387 1444.427 1204.142 1.313 3222.205 1301.360 1. 283 555.5 38 1054.563

Ngày đăng: 19/06/2014, 08:20

Tài liệu cùng người dùng

Tài liệu liên quan