Đang tải... (xem toàn văn)
HỆ THỐNG GẠT MƯA, CỬA KÍNH TRÊN NISSAN VERSA SEDAN ĐỜI 2012
WW-1 DRIVER CONTROLS C D E F G H I J K M SECTION WW A B WW N O P CONTENTS WIPER & WASHER PRECAUTION 3 PRECAUTIONS 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER" 3 Precaution for Procedure without Cowl Top Cover 3 PREPARATION 4 PREPARATION 4 Commercial Service Tool 4 SYSTEM DESCRIPTION 5 COMPONENT PARTS 5 Component Parts Location 5 Component Description 5 SYSTEM 6 System Diagram 6 System Description 6 Fail-Safe 8 DIAGNOSIS SYSTEM (BCM) 9 COMMON ITEM 9 COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) 9 WIPER 10 WIPER : CONSULT Function (BCM - WIPER) 10 DIAGNOSIS SYSTEM (IPDM E/R) 11 CONSULT Function (IPDM E/R) 11 ECU DIAGNOSIS INFORMATION 13 BCM, IPDM E/R 13 List of ECU Reference 13 WIRING DIAGRAM 14 FRONT WIPER AND WASHER SYSTEM 14 Wiring Diagram 14 BASIC INSPECTION 18 DIAGNOSIS AND REPAIR WORKFLOW 18 Work Flow 18 DTC/CIRCUIT DIAGNOSIS 20 WIPER AND WASHER FUSE 20 Description 20 Diagnosis Procedure 20 FRONT WIPER MOTOR LO CIRCUIT 21 Component Function Check 21 Diagnosis Procedure 21 FRONT WIPER MOTOR HI CIRCUIT 23 Component Function Check 23 Diagnosis Procedure 23 FRONT WIPER AUTO STOP SIGNAL CIR- CUIT 25 Component Function Check 25 Diagnosis Procedure 25 FRONT WIPER MOTOR GROUND CIRCUIT 27 Diagnosis Procedure 27 WASHER MOTOR CIRCUIT 28 Diagnosis Procedure 28 WASHER SWITCH 29 Description 29 Component Inspection 29 SYMPTOM DIAGNOSIS 30 WIPER AND WASHER SYSTEM SYMPTOMS 30 Symptom Table 30 FRONT WIPER DOES NOT OPERATE 32 Revision: July 2011 2012 Versa Sedan WW-2 Description 32 Diagnosis Procedure 32 NORMAL OPERATING CONDITION 34 Description 34 REMOVAL AND INSTALLATION 35 FRONT WIPER 35 Exploded View 35 WIPER ARM 35 WIPER ARM : Removal and Installation 35 WIPER ARM : Adjustment 36 WIPER BLADE 36 WIPER BLADE : Removal and Installation 36 WIPER REFILL 37 WIPER REFILL : Removal and Installation 37 WIPER DRIVE ASSEMBLY 37 WIPER DRIVE ASSEMBLY : Removal and Instal- lation 37 WIPER DRIVE ASSEMBLY : Disassembly and Assembly 38 WASHER TANK 40 Exploded View 40 Removal and Installation 40 WASHER PUMP 41 Exploded View 41 Removal and Installation 41 WASHER NOZZLE & TUBE 42 Hydraulic Layout 42 Exploded View 43 WASHER NOZZLE 43 WASHER NOZZLE : Removal and Installation 43 WASHER NOZZLE : Inspection and Adjustment 44 WASHER TUBE 45 WASHER TUBE : Removal and Installation 45 WIPER AND WASHER SWITCH 46 Removal and Installation 46 SERVICE DATA AND SPECIFICATIONS (SDS) 47 SERVICE DATA AND SPECIFICATIONS (SDS) 47 Specifications 47 Revision: July 2011 2012 Versa Sedan PRECAUTIONS WW-3 < PRECAUTION > C D E F G H I J K M A B WW N O P PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000007705964 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SR and SB section of this Service Man- ual. WARNING: • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section. • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- ness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. Precaution for Procedure without Cowl Top Cover INFOID:0000000007206715 When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield. PIIB3706J Revision: July 2011 2012 Versa Sedan WW-4 < PREPARATION > PREPARATION PREPARATION PREPARATION Commercial Service Tool INFOID:0000000007206716 Tool name Description Washer nozzle adjuster. Adjusting washer nozzle. JSLIA0149ZZ Revision: July 2011 2012 Versa Sedan COMPONENT PARTS WW-5 < SYSTEM DESCRIPTION > C D E F G H I J K M A B WW N O P SYSTEM DESCRIPTION COMPONENT PARTS Component Parts Location INFOID:0000000007697697 Component Description INFOID:0000000007697698 1. IPDM E/R 2. Windshield washer tank (view with RF fender protector removed) 3. Front washer motor (view with RF fender protector removed) 4. Front wiper motor (view with cowl top removed) 5. Combination switch (wiper and washer switch) 6. BCM (view with instrument panel removed) AWLIA1890ZZ Component Function BCM • Monitors combination switch status by performing the combination switch reading function. • Sends front wiper relay and front wiper high relay ON signals to IPDM E/R. IPDM E/R • Controls front wiper relay and front wiper high relay. • Performs the auto stop control of the front wiper. Combination switch (Wiper and washer switch) • Provides input for wiper and washer control to BCM. • Refer to WW-6, " System Description" for more information. Front wiper motor • Drives windshield wipers in HI or LO mode. • Sends wiper stop signal to IPDM E/R. Front washer motor Pumps windshield washer fluid to windshield in wash mode. Revision: July 2011 2012 Versa Sedan WW-6 < SYSTEM DESCRIPTION > SYSTEM SYSTEM System Diagram INFOID:0000000007697699 System Description INFOID:0000000007697700 FRONT WIPER CONTROL (BASIC) 1. BCM detects the combination switch position by the combination switch reading function. 2. BCM transmits the front wiper request signal to the IPDM E/R using CAN communication. 3. IPDM E/R controls the integrated front wiper relay and front wiper high relay based on the status of the front wiper request signal. 4. IPDM E/R provides power to operate the front wiper motor. LOW SPEED OPERATION 1. Ignition switch ON. 2. Front wiper switch in LO or MIST position. 3. BCM reads the combination switch position and transmits the front wiper request signal (LO) to IPDM E/R using CAN communication. 4. IPDM E/R turns ON the front wiper relay. HIGH SPEED OPERATION 1. Ignition switch ON. 2. Front wiper switch in HI. 3. BCM reads the combination switch position and transmits the front wiper request signal (HI) to IPDM E/R using CAN communication. 4. IPDM E/R turns ON the front wiper relay and the front wiper high relay. INTERMITTENT OPERATION 1. Ignition switch ON. 2. Front wiper switch INT. 3. BCM reads the combination switch position. BCM calculates the delay interval based on the table below and then transmits the front wiper request signal (INT) to IPDM E/R using CAN communication. 4. IPDM E/R turns ON the front wiper relay only once. 5. BCM detects stop position of the front wiper motor based on the front wiper stop position signal received from the IPDM E/R. 6. BCM transmits the front wiper request signal (INT) again after the delay interval. AWLIA1888GB Revision: July 2011 2012 Versa Sedan SYSTEM WW-7 < SYSTEM DESCRIPTION > C D E F G H I J K M A B WW N O P AUTO STOP OPERATION 1. Front wiper switch is turned OFF. 2. BCM monitors wiper switch position by combination switch reading position function. 3. BCM stops transmitting the front wiper request signal to the IPDM E/R. 4. IPDM E/R detects the front wiper auto stop signal from the position of the front wiper motor (stop position/ except stop position). 5. When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper motor returns to the stop position. 6. IPDM E/R turns the front wiper relay OFF when the front wiper motor has reached the stop position. MIST OPERATION 1. Ignition switch ON. 2. Front washer switch in OFF position. 3. Front wiper switch in MIST position. 4. BCM reads the combination switch position and transmits the front wiper request signal (LO) to IPDM E/R using CAN communication. 5. IPDM E/R turns ON the front wiper relay. 6. The front wiper operates once after the front washer operation. WIPER/WASHER OPERATION 1. Ignition switch ON. JPLIA0094GB Intermittent switch position Length of delay Delay interval (s) 7 Short ↑ ↓ Long 0.4 6 1 5 2 4 3 3 5 2 10 1 16 JPLIA0095GB Revision: July 2011 2012 Versa Sedan WW-8 < SYSTEM DESCRIPTION > SYSTEM 2. Front washer switch ON. 3. The front washer switch provides ground for the front washer motor. 4. BCM reads the combination switch position and transmits the front wiper request signal (LO) to IPDM E/R using CAN communication. 5. BCM transmits the front wiper request signal (LO) to IPDM E/R using CAN communication. 6. IPDM E/R turns ON the front wiper relay. 7. The front wiper operates. NOTE: BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 3 times after front washer switch OFF is detected. Fail-Safe INFOID:0000000007697701 FAIL−SAFE OPERATION IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to PCS-14, " Fail-Safe". Revision: July 2011 2012 Versa Sedan DIAGNOSIS SYSTEM (BCM) WW-9 < SYSTEM DESCRIPTION > C D E F G H I J K M A B WW N O P DIAGNOSIS SYSTEM (BCM) COMMON ITEM COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000007697729 APPLICATION ITEM CONSULT performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions. Direct Diagnostic Mode Description ECU identification The BCM part number is displayed. Self Diagnostic Result The BCM self diagnostic results are displayed. Data Monitor The BCM input/output data is displayed in real time. Active Test The BCM activates outputs to test components. Work support The settings for BCM functions can be changed. Configuration • The vehicle specification can be read and saved. • The vehicle specification can be written when replacing BCM. CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication is displayed. System Sub System Direct Diagnostic Mode ECU identification Self Diagnostic Result Data Monitor Active Test Work support Configuration CAN DIAG SUPPORT MNTR Door lock DOOR LOCK ×××× Rear window defogger REAR DEFOGGER ×× Warning chime BUZZER ×× Interior room lamp timer INT LAMP ××× Remote keyless entry system MULTI REMOTE ENT ××× Exterior lamp HEAD LAMP ××× Wiper and washer WIPER ××× Turn signal and hazard warning lamps FLASHER ×× Air conditioner AIR CONDITIONER × Combination switch COMB SW × BCM BCM × × ××× Immobilizer IMMU ××× Interior room lamp battery saver BATTERY SAVER ××× Trunk open TRUNK × RAP system RETAINED PWR ×× Signal buffer system SIGNAL BUFFER × TPMS AIR PRESSURE MONITOR ×××× Panic alarm system PANIC ALARM × Revision: July 2011 2012 Versa Sedan WW-10 < SYSTEM DESCRIPTION > DIAGNOSIS SYSTEM (BCM) WIPER WIPER : CONSULT Function (BCM - WIPER) INFOID:0000000007697730 DATA MONITOR ACTIVE TEST WORK SUPPORT * : Initial setting Monitor Item [Unit] Description IGN ON SW [On/Off] Indicates condition of ignition switch ON position. IGN SW CAN [On/Off] Indicates ignition switch ON signal received from IPDM E/R on CAN communication line. FR WIPER HI [On/Off] Indicates condition of wiper operation of combination switch. FR WIPER LOW [On/Off] FR WIPER INT [On/Off] FR WASHER SW [On/Off] INT VOLUME [1 − 7] Indicates condition of intermittent wiper operation of combination switch. FR WIPER STOP [On/Off] Indicates front wiper auto stop signal received from IPDM E/R on CAN communication line. REVERSE SW CAN [On/Off] Indicates reverse switch signal received from TCM on CAN communication line. VEHICLE SPEED [km/h/mph] Indicates vehicle speed signal received from combination meter on CAN communication line. Test Item Description FR WIPER This test is able to check front wiper operation [INT/Lo/Hi/Off]. Support Item Setting Description WIPER SPEED SETTING On Front wiper intermittent time linked with vehicle speed and wiper dial position. Off* Front wiper intermittent time linked with wiper dial position. Revision: July 2011 2012 Versa Sedan [...]... Index" G H I J K WW M N O P Revision: July 2011 WW- 13 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM < WIRING DIAGRAM > WIRING DIAGRAM FRONT WIPER AND WASHER SYSTEM Wiring Diagram INFOID:0000000007697706 ABLWA1492GB Revision: July 2011 WW- 14 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM < WIRING DIAGRAM > A B C D E F G H I J K WW M N O ABLIA3161GB P Revision: July 2011 WW- 15 2012 Versa Sedan FRONT WIPER... Revision: July 2011 WW- 15 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM < WIRING DIAGRAM > ABLIA3162GB Revision: July 2011 WW- 16 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM < WIRING DIAGRAM > A B C D E F G H I J K WW M N O ABLIA3163GB P Revision: July 2011 WW- 17 2012 Versa Sedan DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTION > BASIC INSPECTION DIAGNOSIS AND REPAIR WORKFLOW Work Flow INFOID:0000000007697707... Revision: July 2011 WW- 21 2012 Versa Sedan FRONT WIPER MOTOR LO CIRCUIT < DTC/CIRCUIT DIAGNOSIS > IPDM E/R Front wiper motor Connector Terminal Connector Terminal E45 17 E1 3 Continuity Yes Does continuity exist? YES >> Replace front wiper motor Refer to WW- 37, "WIPER DRIVE ASSEMBLY : Removal and Installation" NO >> Repair or replace harness Revision: July 2011 WW- 22 2012 Versa Sedan FRONT WIPER MOTOR... Revision: July 2011 WW- 23 2012 Versa Sedan FRONT WIPER MOTOR HI CIRCUIT < DTC/CIRCUIT DIAGNOSIS > IPDM E/R Front wiper motor Connector Terminal Connector Terminal E45 18 E1 5 Continuity Yes Does continuity exist? YES >> Replace front wiper motor Refer to WW- 37, "WIPER DRIVE ASSEMBLY : Removal and Installation" NO >> Repair or replace harness Revision: July 2011 WW- 24 2012 Versa Sedan FRONT WIPER AUTO... Revision: July 2011 WW- 25 2012 Versa Sedan FRONT WIPER AUTO STOP SIGNAL CIRCUIT < DTC/CIRCUIT DIAGNOSIS > IPDM E/R Front wiper motor Connector Terminal Connector Terminal E46 74 E1 4 Continuity Yes Does continuity exist? YES >> Replace front wiper motor Refer to WW- 37, "WIPER DRIVE ASSEMBLY : Removal and Installation" NO >> Repair or replace harness Revision: July 2011 WW- 26 2012 Versa Sedan FRONT WIPER... Replace front washer motor Refer to WW- 41, "Removal and Installation" NO >> GO TO 4 4 CHECK WASHER SWITCH Check washer switch Refer to WW- 29, "Component Inspection" Is the inspection result normal? YES >> Repair harness between front washer motor washer switch NO >> Replace washer switch Refer to WW- 46, "Removal and Installation" Revision: July 2011 WW- 28 2012 Versa Sedan WASHER SWITCH < DTC/CIRCUIT... operational check Refer to WW- 6, "System Description" >> GO TO 3 3.PERFORM TROUBLE DIAGNOSIS BY SYMPTOM Diagnose the vehicle by performing the appropriate trouble diagnosis Refer to WW- 30, "Symptom Table" >> GO TO 4 4 REPAIR OR REPLACE MALFUNTIONING PARTS Repair or replace the specific parts >> GO TO 5 5 FINAL CHECK Perform a final inspection of the system Revision: July 2011 WW- 18 2012 Versa Sedan DIAGNOSIS... Washer switch OFF No F Is the inspection result normal? YES >> Washer switch is normal NO >> Replace combination switch (wiper and washer switch) Refer to WW- 46, "Removal and Installation" G H I J K WW M N O P Revision: July 2011 WW- 29 2012 Versa Sedan WIPER AND WASHER SYSTEM SYMPTOMS < SYMPTOM DIAGNOSIS > SYMPTOM DIAGNOSIS WIPER AND WASHER SYSTEM SYMPTOMS Symptom Table INFOID:0000000007697720 CAUTION:... washer switch is pressed A B C E H I J K WW M N O P Revision: July 2011 WW- 31 2012 Versa Sedan FRONT WIPER DOES NOT OPERATE < SYMPTOM DIAGNOSIS > FRONT WIPER DOES NOT OPERATE Description INFOID:0000000007697721 The front wiper does not operate under any operation conditions Diagnosis Procedure INFOID:0000000007697722 Regarding Wiring Diagram information, refer to WW- 14, "Wiring Diagram" 1 CHECK WIPER... wiper motor ground circuit is normal NO >> Repair or replace harness G H I J K WW M N O P Revision: July 2011 WW- 27 2012 Versa Sedan WASHER MOTOR CIRCUIT < DTC/CIRCUIT DIAGNOSIS > WASHER MOTOR CIRCUIT Diagnosis Procedure INFOID:0000000007697717 Regarding Wiring Diagram information, refer to WW- 14, "Wiring Diagram" 1 CHECK FRONT WASHER MOTOR FUSE 1 2 Turn the ignition switch OFF Check that the following . INFOID:0000000007697706 ABLWA1492GB Revision: July 2011 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM WW-15 < WIRING DIAGRAM > C D E F G H I J K M A B WW N O P ABLIA3161GB Revision: July 2011 2012 Versa Sedan WW-16 < WIRING. SYSTEM ABLIA3162GB Revision: July 2011 2012 Versa Sedan FRONT WIPER AND WASHER SYSTEM WW-17 < WIRING DIAGRAM > C D E F G H I J K M A B WW N O P ABLIA3163GB Revision: July 2011 2012 Versa Sedan WW-18 < BASIC. windshield with urethane, etc to prevent damage to windshield. PIIB3706J Revision: July 2011 2012 Versa Sedan WW-4 < PREPARATION > PREPARATION PREPARATION PREPARATION Commercial Service Tool