[...].. .Tailstock Operation .91 Manual Tailstock Operation 91 Pneumatic Tailstock Operation 91 Routine Maintenance 92 Lubrication .92 Tailstock Assembly Drawings 92 HTS 4, 5, 6, 9 Manual Tailstocks 92 HPTS 4, 5, 6, 9 Pneumatic Tailstocks 93 HTS Manual Tailstocks .94 HPTS Pneumatic Tailstocks .95 HTS 11.5 and HTS 14.5 Manual Tailstocks... regulations as outlined in the CE directive for Machining Centers: ·· Machinery Directive 200 6/4 2/EC ·· Electromagnetic Compatibility Directive 200 4/1 08/EC ·· Low Voltage Directive 200 6/9 5/EC Additional Standards: ·EN 60204-1:2006/A1:2009 · ·EN 614-1:2006+A1:2009 · ·EN 894-1:1997+A1:2008 · ·EN 13849-1:2008/AC:2009 · ·EN 14121-1:2007 · RoHS: COMPLIANT by Exemption per producer documentation Exempt by:... MAX.TRAVEL TAILSTOCK 10.50 1.450 29.5 38.80 MAX 1 Position the tailstock so that the tailstock quill is extended between 3/4 " to 1- 1/4 " This will optimize spindle rigidity (item A) 2 Tailstock to HA5C head alignment can be accomplished by pushing the tailstock (item B) to one side of the T-slots prior to tightening the flange nuts to 50 ft-lbs Precision locating pins mounted on the bottom of the tailstock. .. (2) T-nuts from the rotary platter Keep all hardware and shipping brackets Haas Tailstocks Tailstocks with live centers are recommended !Warning! Tailstocks cannot be used with the HRT320FB table Clean the bottom surface of the tailstock casting before mounting it to the mill table If there are any noticeable burrs or nicks on the mounting surface, clean them with a deburring stone Tailstocks must be... cable is cut, the motor will fail prematurely Rotary Table Mounting NOTE: The HRT 160, 210, 450, and 600 Rotary Tables can be secured as shown: 1/2 -13UNC T-Nuts, Remove Top Studs, Flange nuts Cover to Access and Washers* Toe-Clamp Pockets Bottom of Casting 1/2 -13UNC T-Nuts, Studs, Flange Nuts, and Washers* Clamping Tool Assembly (2) 1/4 -20UNC SHCS (4) 1/2 -13UNC T-Nuts, Studs, Flange nuts, and Washers... Table-to-Fixture Bolt Hole Pattern 3 Original Instructions HA5C Mounting N TIO MA TO AU IN U.S.A MADE 1/2 -13UNC Flange Nuts (2) 1/2 -Inch Washers (2) 1/2 -13UNC T-Nuts, Studs, Flange nuts and Washers 1/2 -13UNC T-nuts (2) 1/2 -13UNC Studs (2) 1 Secure the unit to the mill table 2 Connect the cables from the rotary unit to the control, with the power off Never connect or disconnect the cables with the power... number: SCPB) 10-32X 3/8 BHCS Locations 96-0315 Rev R December 2012 1 Original Instructions TR-Series Shipping Bracket Removal Remove the shipping bracket before using TR160(160-2)/TR210: The shipping bracket is located on the left rear of the unit Replace the (2) 10-32 and (2) 1/4 -20 screws, do not replace the 1/2 -13 bolt The TR160 does not have a 1/2 -13 bolt TR310: Remove the (4) 1/2 -13 bolts and washers... Control Options 3 Black 4 White/Black 5 Red DER OR Momentary Switch 2 White/Orange 6 Brown Remote Quill Switch Manual Operation To manually control the HIT210, use a momentary switch cable (32-5104) connected to the end of the control portion of the power and control cable The table rotates 45 degrees for each press of the button Automatic Operation Direct to Control: Connect the rotary control cable to the... between the mill and Haas rotary control Since most CNC machine tools are equipped with spare M-codes, semi-fourth axis machining is achieved by connecting one end of the CNC Interface Cable to any of these spare relays (switches), and the other to the Haas rotary control Commands for the rotary unit are stored in rotary control memory, and each pulse of the mill relay, triggers the rotary control to move... surface, clean them with a deburring stone Tailstocks must be properly aligned to the rotary table before using See the tailstock section of this manual for more information and the operating pressure of pneumatic tailstocks 2 Original Instructions 96-0315 Rev R December 2012 General Setup There are a number of ways the rotary products can be installed Use the following pictures as a guide Route the cable . 9 manual taIlStockS 92 HptS 4, 5, 6, 9 pneumatIc taIlStockS 93 HtS manual taIlStockS 94 HptS pneumatIc taIlStockS 95 HtS 11.5 and HtS 14.5 manual taIlStockS . Directive 200 6/4 2/EC · Electromagnetic Compatibility Directive 200 4/1 08/EC · Low Voltage Directive 200 6/9 5/EC Additional Standards: ·EN 60204-1:2006/A1:2009