Đang tải... (xem toàn văn)
Environmental chemistry of phosphonates
ARTICLE IN PRESS Water Research ] (]]]]) ]]]–]]] Review Environmental chemistry of phosphonates Bernd Nowack* Institute of Terrestrial Ecology (IT . O), Swiss Federal Institute of Technology Z . urich (ETH), Grabenstrasse 3, CH-Schlieren 8952, Switzerland Received 16 August 2002; received in revised form 21 January 2003; accepted 31 January 2003 Abstract Phosphonates are anthropogenic complexing agents containing one or more C–PO(OH) 2 groups. They are used in numerous technical and industrial applications as chelating agents and scale inhibitors. Phosphonates have properties that differentiate them from other chelating agents and that greatly affect their environmental behavior. Phosphonates have a very strong interaction with surfaces, which results in a significant removal in technical and natural systems. Due to this strong adsorption, little or no remobilization of metals is expected. No biodegradation of phosphonates during water treatment is observed but photodegradation of the Fe(III)-complexes is rapid. Aminopolyphosphonates are also rapidly oxidized in the presence of Mn(II) and oxygen and stable breakdown products are formed that have been detected in wastewater. The lack of information about phosphonates in the environment is linked to analytical problems of their determination at trace concentrations in natural waters. Further method development is urgently needed in this area, including speciation of these compounds. With the current knowledge on speciation, we can conclude that phosphonates are mainly present as Ca and Mg-complexes in natural waters and therefore do not affect metal speciation or transport. r 2003 Elsevier Science Ltd. All rights reserved. Keywords: Phosphonates; Chelating agents; Adsorption; Heavy metals; Degradation; Speciation Contents 1. Introduction . . . . . . . . 2 2. Properties . . . . . . . . . . 2 3. Analysis of phosphonates . . 4 3.1. Analytical methods . . . . . . . 4 3.2. Concentrations in the environment . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Surface reactions . . . . . . 5 4.1. Adsorption . . . . . . . . . . . 5 4.2. Dissolution of minerals . . . . . 6 4.3. Remobilization of metals . . . . 6 4.4. Precipitation . . . . . . . . . . 7 4.5. Inhibition of dissolution and precipitation . . . . . . . . . . . . . . . . . . . . 7 *Tel.: +41-1-633-61-60; fax: +41-1-633-11-23. E-mail address: nowack@ito.umnw.ethz.ch (B. Nowack). 0043-1354/03/$ - see front matter r 2003 Elsevier Science Ltd. All rights reserved. doi:10.1016/S0043-1354(03)00079-4 1. Introduction Phosphonic acids, compounds containing the Lewis acid moiety R-CP(O)(OH) 2 , are characterized by a stable, covalent carbon to phosphorous bond. The corresponding anions of the phosphonic acids are called phosphonates. The most commonly used phosphonates are structural analogues to the well-known aminopoly- carboxylates such as ethylenediaminetetra acetate (EDTA) and nitrilotriacetate (NTA). The environmental fate of these aminopolycarboxylate chelating agents has received considerable attention [1–5]. Much less is known about the fate and behavior of the corresponding phosphonates in the environment [4,6,7]. The existing reviews are either several years old and therefore do not cover the newest literature [6] or focus on toxicology and risk assessment based on the limited data that were available at that time [7]. What is missing is an overview of the chemistry of these compounds which can help us to understand and predict the environmental behavior of these compounds more accurately and that can be the basis for a refined risk assessment. The aim of this review is therefore to provide an overview of the current knowledge of the environmental chemistry of phospho- nates. It concentrates on polyphosphonates, compounds containing more than one phosphonic acid group, and especially aminopolyphosphonates, compounds contain- ing several phosphonate and one or more amine groups. Glyphosate, a herbicide containing a phosphonate, a carboxylate and an amine functional group, is not discussed in detail in this review. There is, however, much information available about the environmental chemistry and behavior of this compound [8–10]. This review starts with a short description of the properties of phosphonates and their analysis. Phos- phonates have a very strong interaction with surfaces and the section discussing the surface reaction follows: adsorption, dissolution of minerals, remobilization of metals, precipitation of phosphonates and inhibition of precipitation of minerals are covered. In the degradation section biodegradation, photodegradation, chemical degradation and degradation during oxidation processes are discussed. The speciation of phosphonates in the environment covers the next section, which is followed by a discussion of their environmental behavior. This section contains a summary of the data on measured concentrations of phosphonates and their behavior during wastewater treatment. 2. Properties Table 1 lists the abbreviations, names and structures of the phosphonates discussed in this review. These compounds are known under many different abbrevia- tions that vary between the disciplines and countries and have changed with time. Phosphonates are effective chelating agents according to the IUPAC definition that chelation involves coordination of more than one sigma- electron pair donor group from the same ligand to the same central atom. Phosphonates are used as chelating agents in many applications, e.g. in pulp, paper and textile industry to complex heavy metals in chlorine-free bleaching solutions that could inactivate the peroxide. In medicine phosphonates are used to chelate radionuclides for bone cancer treatments [11]. A recent IUPAC Technical Report [12] critically evaluates the available experimental data on stability constants of proton and metal complexes for phospho- nic acids. It presents high-quality data as ‘‘recom- mended’’ or ‘‘provisional’’ constants while for example, all constants for DTPMP have been rejected due to insufficient purity of the parent compound. This report will be of great use for all future speciation calculations and should be the sole source of stability constants when ever possible. The stability of the metal complexes increases with increasing number of phosphonic acid groups. Fig. 1 shows that the monophosphonate aminomethylpho- sphonic acid (AMPA) has the lowest stability constants ARTICLE IN PRESS 5. Degradation . . . . . . . . 7 5.1. Biodegradation . . . . . . . . . 7 5.2. Photodegradation . . . . . . . . 8 5.3. Chemical degradation . . . . . 8 5.4. Degradation during oxidation processes . . . . . . . . . . . . . . . . . . . . . 9 6. Speciation . . . . . . . . . . 9 7. Behavior during wastewater treatment . . . . . . . . . . . . . . . . . . . . 10 8. Conclusions . . . . . . . . . 11 Acknowledgements . . . . . . . 11 References . . . . . . . . . . . . 11 B. Nowack / Water Research ] (]]]]) ]]]–]]]2 ARTICLE IN PRESS Table 1 Abbreviations, names, and structures of the phosphonates covered in this review Abbreviation Other abbreviations also in use Name Structure HEDP HEDPA, HEBP 1-Hydroxyethane(1,1-diylbisphosphonic acid) C PO(OH) 2 H 3 COH PO(OH) 2 NTMP ATMP, NTP, NTPH, NTPO Nitrilotris(methylenephosphonic acid) N (HO) 2 OP (HO) 2 OP PO(OH) 2 EDTMP EDTP, EDTPH, ENTMP, EDTMPO, EDTMPA 1,2-Diaminoethanetetrakis (methylenephosphonic acid) N NPO(OH) 2 PO(OH) 2 (HO) 2 OP (HO) 2 OP DTPMP DETPMP, DTPPH, DETPMPA, DETPMPO Diethylenetriaminepentakis (methylenephosphonic acid) N N (HO) 2 OP (HO) 2 OP N PO(OH) 2 PO(OH) 2 PO(OH) 2 PBTC PBTCA Phosphonobutane-tricarboxylic acid C COOH PO(OH) 2 HOOC COOH B. Nowack / Water Research ] (]]]]) ]]]–]]] 3 and EDTMP with 4 phosphonic aid groups the highest. The log K values of the different transition metal complexes follow the Irving–Williams series Mn 2+ o- Fe 2+ oCo 2+ oNi 2+ oCu 2+ >Zn 2+ . Fig. 2 shows a speciation diagram for the system Zn- EDTMP calculated with the constants from [12] with the speciation program ChemEQL [13]. This calculation shows that in the pH range found in technical applications and in natural waters a large number of possible complexes with different degree of protonation and charge exist. At pH 6 the species H 4 EDTMP 4À , ZnH 3 EDTMP 3À , ZnH 2 EDTMP 4À and ZnHEDTMP 5À occur at a percentage of more than 5% of total EDTMP. Complexation of other metals by other phosphonates is similar and at each pH value several species coexist. Phosphonates are not only chelating agents but also very potent inhibitors of mineral precipitation and growth. This effect works at concentrations well below the amount needed to chelate all metals. An important industrial use of phosphonates is in cooling waters, desalination systems and in oil fields to inhibit scale formation, e.g. barium sulfate or calcium carbonate precipitation. Phosphonates are also used in medicine to treat various bone and calcium metabolism diseases [14]. In detergents phosphonates are used as a combination of chelating agent, scale inhibitor and bleach stabilizer [15]. Phosphonates are highly water-soluble while the phosphonic acids are only sparingly soluble. Phospho- nates are not volatile and poorly soluble in organic solvents. More detailed data on the physico- chemical properties of the phosphonates can be found in reference [7]. The consumption of phosphonates was 56,000 tons worldwide in 1998 [16] and 16,000 tons in Europe in 1999 [4]. Data about the distribution among the various phosphonates are available for Europe and the US [6], for the Netherlands [7] and for Germany [4]. HEDP and DTPMP are the most important phosphonates based on the used volumes. The toxicity of phosphonates to aquatic organisms is low [6,7,17]. Reported values for 48 h LC50 values for fish are between 0.1 and 1.1 mM [18,19]. Also the bioconcentration factor for fish is very low [20,21]. Phosphonates are poorly absorbed in the gastro- intestinal tract and most of the absorbed dose was rapidly excreted by the kidneys [22]. Human toxicity is also low which can be seen in the fact that phosphonates are used to treat various diseases [14,23]. 3. Analysis of phosphonates 3.1. Analytical methods The absence of a reliable trace analytical method for phosphonates results in a lack of detailed information about the environmental behavior of phosphonates. Most of the current methods for phosphonate determi- nation have detection limits above the expected natural concentrations or suffer from interferences in natural samples. The standard method for the determination of phosphonates is ion-chromatography followed by post- column reaction with Fe(III) and detection of the Fe(III)-complexes at 300–330 nm [24–26]. This method has a detection limit of about 2–10 mM. Other methods have been developed based on post-column oxidation of the phosphonate to phosphate and detection of phos- phate with the molybdenum blue method [27]. Ion- chromatography with pulsed amperometric detection of amine-containing phosphonates [28], ion-chromatogra- phy with indirect photometric detection [29] and capillary electrophoresis with indirect photometric detection have also been described [30]. These methods all have high detection limits of 1 mM or more and are therefore not suitable for natural systems. A very powerful method is the derivatization of the phosphonic acid group with diazomethane and ARTICLE IN PRESS 0 2 10 -7 4 10 -7 6 10 -7 8 10 -7 1 10 -6 2 4 6 8 10 12 concentration (M) pH H 5 EDTMP 3 - H 6 EDTMP 2 - ZnHEDTMP 5 - HEDTMP 7 - ZnH 2 EDTMP 4 - ZnH 3 EDTMP 3 - H 4 EDTMP 4 - H 7 EDTMP - Fig. 2. Speciation of 1 mM EDTMP in the presence of 1 mM Zn. The diagram has been calculated using the constants from [12]. 0 5 10 15 20 Mn 2+ Fe 2+ Co 2+ Ni 2+ Cu 2+ Zn 2+ log K (M + HL) EDTMP NTMP HEDP AMPA IDMP Fig. 1. Stability constants of 1:1 complexes (M+HL) with transition metals of AMPA, IDMP, HEDP, NTMP and EDTMP (Irving–Williams series) with data from [12]. B. Nowack / Water Research ] (]]]]) ]]]–]]]4 separation and detection of the derivatives by HPLC- MS [31]. This method is however, not applicable to natural waters due to interference by the major cations and anions of the water matrix. The only method with a low enough detection limit in natural samples is an ion- pair HPLC method with precolumn formation of the Fe(III)-complexes [32]. The phosphonates can be measured with a detection limit of 0.05 mM in natural waters and wastewaters. The method, however, is not able to quantify bisphosphonic acids such as HEDP at low concentrations. This is a major drawback because HEDP is one of the most used phosphonates [4,6]. The breakdown products of the Mn(II)-catalyzed degradation of NTMP [33], iminodimethylenephospho- nic acid (IDMP) and N-formyl-iminodimethylenephos- phonic acid (FIDMP), can be detected after derivatization of the aldehyde group in FIDMP by 2,4-dinitrophenylhy- drazine and derivatization of the imine-group in IDMP by 9-fluorenyl methylchloroformate [34]. A detection limit of 0.01 mMFIDMPand0.02mM IDMP has been achieved. Anion-exchange chromatography coupled to ICP-MS is able is a very promising method for chelating agent analysis [35,36]. The method is also applicable to phosphonates and it has been shown that CuEDTMP can be determined with a very low detection limit in the nanomolar range. Preconcentration of phosphonates from natural water samples using different adsorbents has been tested [37]. It was found that the investigated phosphonates HEDP, NTMP, and EDTMP differed so much in their chemical behavior that a simultaneous enrichment from natural samples cannot be achieved. Successful preconcentra- tion of the phosphonates NTMP, EDTMP and DTPMP from natural waters or wastewaters was achieved using freshly precipitated CaCO 3 [32]. Recoveries at the 1 mM level were 95–102% for an influent sample of a wastewater treatment plant. 3.2. Concentrations in the environment No measurements of phosphonates in natural samples have been reported and only data for wastewaters are available. This is mainly due to the fact that most analytical methods are not able to quantify phospho- nates in natural waters at low concentrations. Phospho- nates have been measured in Swiss wastewater treatment plants (WWTP) [38]. The concentrations of NTMP were between o0.05 and 0.85 mM, of EDTMP between o0.05 and 0.15 mM and of DTPMP between o0.05 and 1.7 mM. The highest concentration of DTPMP was found in a WWTP influenced by textile industry. Effluent samples from all investigated WWTP were with the exception of one case always below the detection limit. Another WWTP influenced by textile industry contained NTMP concentrations in the influent between 0.2 and 1.1 mM [39]. The oxidative breakdown products of NTMP, IDMP and FIDMP, have been detected in two WWTPs receiving water from textile industry at concentrations of 0.08 and 0.015 mM FIDMP and 0.49 and 0.3 mM IDMP in the influent [34]. The expected concentrations in rivers are maximal 0.1 mM and with adsorption/photodegradation included about 1–4 nM for NTMP and 25 nM for HEDP [6,7]. Locally higher concentrations can be expected because of intermitted discharge of cooling tower water. 4. Surface reactions 4.1. Adsorption Phosphonates adsorb very strongly onto almost all mineral surfaces. This behavior distinguishes them from the corresponding aminocarboxylates, which exhibit much weaker interaction with mineral surfaces, espe- cially near neutral pH [40]. Some of the investigated adsorbents for phosphonates are calcite [41], clays [42,43], aluminum oxides [44–46], iron oxides [47–49], zinc oxide [49], hydroxyapatite [50,51] and barite [52]. For all those compounds very strong adsorption is observed in the pH range of natural waters. Natural materials are also very potent adsorbents for phospho- nates, for example sewage sludge [20,21,39,53,54], sediments [54] and soils [55]. Most of these studies, however, have not considered that metal ions might significantly alter the adsorption of a chelating agent [56]. However, no influence of Fe(III), Zn, and Cu(II) on phosphonate adsorption onto goethite was observed [49]. This was explained by the very strong adsorption of the uncomplexed phosphonate, which resulted in a dissociation of the complex at the surface and separate adsorption of the metal and the phosphonate onto different surface sites. Fig. 3 shows the adsorption of NTMP and the NTMP complexes with Zn, Cu and Fe(III). Complete adsorption is observed up to a pH of 8 and no influence of the complexed metal on the shape of the adsorption edge can be seen. In the pH range of natural waters adsorption is therefore very strong. Other phosphonates, e.g. HEDP, EDTMP and DTPMP, adsorb in a similar manner to NTMP. Ca has a very strong positive effect on phosphonate adsorption [49]. In the presence of mM Ca concentra- tions, phosphonates were completely adsorbed up to pH of 12. The maximum surface concentration of phospho- nates was also greatly enhanced in the presence of Ca. This effect can be explained by the formation of ternary surface-phosphonate-Ca complexes. Precipitation of Ca- phosphonates on the surface can be ruled out [49]. When evaluating the adsorptive capacity of a surface towards phosphonates in a natural system, it is therefore ARTICLE IN PRESS B. Nowack / Water Research ] (]]]]) ]]]–]]] 5 necessary to conduct the adsorption experiments under natural Ca concentrations. 4.2. Dissolution of minerals Dissolution of a mineral phase by chelating agents can be explained in terms of a ligand exchange process and is related to the concentration of surface bound ligands. The ligands weaken the metal–oxygen bonds on the surface and enhance the release of metal ions from the surface into the adjacent solution [57]. Reactions with iron oxides are especially of great importance regarding the speciation of the ligand in solution due to the very strong Fe(III)-complexes. Reactions like this have been observed in subsurface systems and have a pronounced influence on the mobility of heavy metals [58,59]. Very little is known about the dissolution of iron oxides by phosphonates. It was observed that HEDP significantly mobilized Fe from natural sediments but no information was given about the pH value of the experiments [60]. No enhanced solubilization of Fe from river sediment was observed at pH 3 by 0.01 M NTMP [61]. The concentration of the Fe(III)-complex in the presence of an iron oxide phase can be calculated when the stability constants of the Fe(III)-complexes are known. Fig. 4 shows the calculated Fe(III)NTMP concentration in a system with NTMP and hydrous ferric oxide (HFO). The speciation has been calculated with the published stability constants for metal-NTMP complexes [12] and the NTMP-Fe(III) stability con- stants from [62] using the program ChemEQL [13]. The formation of Fe(III)NTMP is important at pH values below 6 in the absence of other metal ions. At pH above 7 NTMP is present as uncomplexed ligand. 1 mM Ca and equimolar Zn depress the formation of Fe(III)NTMP slightly. Cu which forms the strongest complexes with NTMP has the largest influence on Fe(III)NTMP formation. We can therefore conclude that dissolution reactions are able to occur at low pH. However, the strong adsorption of phosphonates, especially at low pH, will limit the formation of dissolved Fe(III)NTMP complexes and therefore no dissolution will occur at low, environmentally relevant concentrations. 4.3. Remobilization of metals Metals adsorbed onto a mineral surface can be solubilized by chelating agents. This process has always been mentioned as one of the most adverse effects of elevated chelating agent concentrations in the environ- ment [63]. Metal adsorption in the presence of phosphonates has been studied. There is an increase in Cu adsorption in the presence of phosphonates at low pH, which is caused by electrostatic effects [49]. At high pH there is a mobilization of Cu due to the formation of dissolved Cu-phosphonate complexes. Fig. 5 shows as an example the influence of EDTMP on Cu adsorption onto goethite. Overall, the influence of phosphonates on metal adsorption in the natural pH range from 4 to 8 is weak. We can therefore expect that phosphonates have only a slight influence on metal remobilization in natural systems. This was actually found during the study of metal mobilization from river sediments by the phos- phonate HEDP [60]. The only metal to be remobilized was Fe whereas Zn, Cr, Ni, Cu, Pb and Cd were not increased compared to a blank sample and only dissolution of iron oxides was observed. Remobilization of Cu, Cd, and Pb from river sediment was only observed at NTMP concentrations above 0.1 mM [61]. ARTICLE IN PRESS 0 20 40 60 80 100 4681012 NTMP ZnNTMP CuNTMP Fe(III)NTMP NTMP/ 1 mM Ca % adsorbed pH Fig. 3. Adsorption of 10 mM NTMP onto goethite in the absence and presence of equimolar Zn, Cu, and Fe(III) and 1 mM Ca. Reprinted with permission from [49]. Copyright (1999) American Chemical Society. 0 2 10 -7 4 10 -7 6 10 -7 8 10 -7 1 10 -6 4 4.5 5 5.5 6 6.5 7 7.5 8 NTMP 2 mM Ca 1 µM Zn 1 µM Cu Fe(III)NTMP pH Fig. 4. Speciation of 1 mM NTMP in the presence of HFO and in the absence and presence of 1 mM Zn and Cu and 2 mM Ca without considering adsorption of the phosphonate. Log K values from [12] and [62]. B. Nowack / Water Research ] (]]]]) ]]]–]]]6 We can therefore conclude that phosphonates probably have only a marginal influence on metal mobilization in the environment. 4.4. Precipitation In many applications, phosphonates are added to waters containing high concentrations of dissolved ions to prevent the formation of precipitates. However, due to the insolubility of some metal-phosphonates, the phosphonates itself can precipitate. This phenomenon often occurs in oil field applications when phosphonates are injected into the subsurface and are left to interact with calcium-containing formation waters [64,65]. The solubility of precipitates of NTMP with divalent metals increases in the order CaoBaoSroMg [66]. The insoluble Ca precipitates of DTPMP [67,68], NTMP [69], and HEDP [70] and the precipitates of NTMP with Fe(II) [71] and Fe(III) [72] have been investigated in detail. Insoluble products of HEDP are also formed with heavy metals such as Pb and Cd [73]. The precipitates are important in oil field applications or in technical systems where high phosphonate and high ion concentration occur simultaneously. In natural waters or wastewaters, the phosphonate or Ca concen- trations are far too low to exert any influence on phosphonate concentrations. The solubility of NTMP in the presence of 1 and 5 mM Ca is always above 200 mM [49]. In natural waters precipitation reactions are there- fore not important. 4.5. Inhibition of dissolution and precipitation Scale formation, e.g. precipitation of calcium carbo- nate or calcium sulfate, is a significant problem in commercial water treatment processes including cooling water technology, desalination and oil field applications. This scale formation can be alleviated by the use of chemical water treatment additives, known as ‘‘thresh- old inhibitors’’. Phosphonic acids are among the most potent scale inhibitors next to the polyphosphates. They poison the crystal growth at concentrations far below stoichiometric amounts of the reactive cations. Models for this poisoning include inhibition of nucleation, adsorption onto growth sites, distortion of the crystal lattice, changes in surface charge and association with precursors of crystal formation [74,75]. The morphology of crystals formed in the presence of phosphonates is markedly different from those in the absence of phosphonates [76]. Phosphonates limit the size of the growing crystals and produce a lag phase in which crystal growth is greatly reduced [77]. It was found that the ability of different phosphonates to inhibit crystal growth can be interpreted in terms of the Langmuir adsorption model with the strongest inhibi- tory effect from compounds that adsorb most strongly [78]. Due to their inhibitory effect on crystal growth it has been argued that phosphonates may have an adverse effect on phosphate elimination by precipitation with iron or aluminum salts during wastewater treatment [79,80]. It was found that the phosphonates had an influence on flocculation but it was possible to compensate for it by increased addition of flocculating agent. The resulting particulate precipitation products were stabilized by the dispersing action of the phospho- nates and not retained in the sand filter. Another study, however, found no influence of HEDP on phosphate elimination [60]. 5. Degradation 5.1. Biodegradation Phosphonates are similar to phosphates except that they have a carbon–phosphorous (C–P) bond in place of the carbon–oxygen–phosphorous (C–O–P) linkage. Due to their structural similarity to phosphate esters, phosphonates often act as inhibitors of enzymes due in part to the high stability of the C–P bond [81]. In nature bacteria play a major role in phosphonate biodegrada- tion. The first phosphonate to be identified to occur naturally was 2-aminoethylphosphonic acid [82].Itis found in plants and many animals, mostly in mem- branes. Phosphonates are quite common among differ- ent organisms, from prokaryotes to eubacteria and fungi, mollusks, insects and others but the biological role of the natural phosphonates is still poorly under- stood [83]. Due to the presence of natural phosphonates in the environment, bacteria have evolved the ability to metabolize phosphonates as nutrient sources. Those bacteria able of cleaving the C–P bond are able to use phosphonates as a phosphorous source for growth. ARTICLE IN PRESS Cu alone Cu with NTMP 4681012 pH % Cu adsorbed 0 20 40 60 80 100 Fig. 5. Adsorption of 10 mM Cu onto goethite in the absence and presence of 10 mM NTMP. Reprinted with permission from [49]. Copyright (1999) American Chemical Society. B. Nowack / Water Research ] (]]]]) ]]]–]]] 7 Aminophosphonates can also be used as sole nitrogen source by some bacteria [84]. The polyphosphonate chelating agents discussed here differ greatly from natural phosphonates such as 2- aminoethylphosphonic acid, because they are much larger, carry a high negative charge and are complexed with metals. Biodegradation tests with sludge from municipal sewage treatment plants with HEDP and NTMP showed no indication for any degradation based on CO 2 formation [18,20,21]. An investigation of HEDP, NTMP, EDTMP and DTPMP in standard biodegradation tests also failed to identify any biode- gradation [53]. It was noted, however, that in some tests due to the high sludge to phosphonate ratio, removal of the test substance from solution observed as loss of DOC was observed. This was attributed to adsorption rather than biodegradation because no accompanying increase in CO 2 was observed. However, bacterial strains capable of degrading aminopolyphosphonates and HEDP under P-limited conditions have been isolated from soils, lakes, waste- water, activated sludge and compost [85]. The phospho- nate phosphonobutane-tricarboxylic acid (PBTC) was also rapidly degraded by microbial enrichment cultures from a variety of ecosystems under conditions of low phosphate availability [86]. The effects of other more accessible P sources on phosphonate uptake and degradation are of great environmental importance. Many environments such as activated sludge, sediments and soils that act as a sink for phosphonates are not characterized by a lack of P most of the time. Because phosphonates are utilized almost exclusively as P-source, little biodegradation can be expected under these conditions. It has been demonstrated, however, that simultaneous phosphate and phosphonate utilization by bacteria can occur [87]. Adsorption of chelating agents by surfaces has been shown to decrease the biodegradability. The easily biodegradable NTA for example is much slower degraded when adsorbed to mineral surfaces [88].It can be expected that phosphonates with their higher affinity to surfaces are much slower degraded in a heterogeneous compared to a homogeneous system. This was found to be the case for N-phosphonomethyl- glycine, the phosphonate-containing herbicide glypho- sate [89]. Phosphonates are therefore similar to EDTA [3,90] in that little or no biodegradation is observed in natural systems but that microorganisms have been isolated from these environments capable of degrading the compound. 5.2. Photodegradation Photodegradation of the Fe(III)-complexes is an important pathway of aminopolycarboxylate elimination in the environment [91]. Phosphonates have a similar reactivity. In distilled water and in the presence of Ca no photodegradation of HEDP was observed but the addition of Fe(III) and Cu(II) resulted in rapid photo- degradation [20,92]. The mechanism of Fe(III)EDTMP photodegradation [93] is equivalent to the photodegra- dation of Fe(III)EDTA [94]. Fe(III)EDTMP is degraded in a stepwise process from the parent compound through ethylenediaminetrimethylenephosphonate and ethylene- diaminedimethylenephosphonate to ethylenediaminemo- nomethylenephosphonate which is stable in the presence of Fe(III) and light. For EDTA the photodegradation of the Fe(III)-complexes is the major elimination pathway in natural waters [91]. We can therefore expect that photodegradation is also very important for the fate of dissolved phosphonates in surface waters. The photo- degradation products of Fe(III)EDTA are readily biodegradable, but this is not the case for phosphonates [95]. 5.3. Chemical degradation Phosphonates are very stable and breakdown of uncomplexed phosphonates requires long timescales and severe chemical conditions. At temperatures above 200 C free NTMP decomposes to various breakdown products [96,97]. These conditions are important for the fate of the chelating agents in technical systems at elevated temperatures, e.g. in cooling waters of power plants, but not for natural waters. One study performed at room temperature within the pH range of 2–10 reported that over a several month period, EDTMP hydrolyzed under formation of phosphate, phosphite and hydroxymethylphosphonate (HMP) [98]. Other phosphonate-containing breakdown products were pre- sent but were not identified. No information on the kinetics or the percentage degraded was given. In natural waters chelating agents and therefore the phosphonates always occur in the form of metal complexes. Studies on the chemical degradation of phosphonates should therefore always include the presence of metals. Degradation of the amine linkage- containing phosphonates NTMP, EDTMP, and DTPMP was negligible in metal-ion free oxygenated solutions, but Ca, Mg, and Fe(II) brought about conversion to free phosphate at a rate of approximately 1 percent per day [99]. Although the degradation was classified as hydrolysis, the conversion rate dropped to negligible levels in the absence of O 2 , indicating that redox reactions play a role. HEDP, which does not contain an amine linkage, degrades approximately 20- times more slowly. A loss of NTMP in different natural waters (river waters, groundwaters) and appearance of the degrada- tion products has been observed [21]. The conversion of NTMP into iminodimethylenephosphonate (IDMP) and ARTICLE IN PRESS B. Nowack / Water Research ] (]]]]) ]]]–]]]8 HMP was attributed to abiotic hydrolysis and the subsequent conversion to aminomethylphosphonate (AMPA) and CO 2 to microbial degradation. The authors performed a follow-up study in a medium that was free of microorganisms, but contained mM levels of Ca, Mg, K, and Na and trace levels (o1 mM) of Fe(III), Cu(II), Mn(II), and Zn. Complete conversion of NTMP to IDMP, HMP and AMPA occurred within 32 h. Because multiple metal ions were present in these investigations [21,99], it was not possible to identify the catalytic agent. A systematic study on the influence of metal ions on phosphonate breakdown has been reported [33].No breakdown of NTMP was observed in metal-free systems and in the presence of Ca, Mg, Zn, Cu(II) and Fe(III) which disagrees to previous results where degradation of NTMP was observed in the presence of Ca or Mg [21]. Very rapid degradation of aminopoly- phosphonates occurred in the presence of Mn(II) and molecular oxygen [33]. The half-life for the reaction of NTMP in the presence of equimolar Mn(II) and in equilibrium with 0.21 atm O 2 was 10 min at pH 6.5. The reaction occurs more slowly under more alkaline or acidic conditions. In the absence of oxygen no reaction took place, indicating that an oxidation step was involved. The presence of other cations such as Ca, Zn, and Cu(II) can considerably slow down the reaction by competing with Mn(II) for NTMP (Fig. 6). Catalytic Mn(II) is regenerated by oxygen in cyclic fashion as the reaction takes place. The hypothesized pathway is that Mn(II)-phosphonate is oxidized by molecular oxygen to the Mn(III)-phosphonate. In an intramolecular redox- reaction the Mn(III) oxidizes the phosphonic acid and is in turn reduced to Mn(II). Formate, orthophosphate, IDMP and FIDMP break- down products have been identified. Breakdown also occurs in oxygen-free suspension of the Mn(III) containing mineral manganite (MnOOH) and with MnOOH in the presence of oxygen [100]. EDTMP and DTPMP are also degraded in the presence of Mn(II) and oxygen, although at a slower rate, but not the amine-free HEDP [33]. Two of the breakdown products of NTMP, IDMP and FIDMP, have been detected in WWTP [34]. This indicates that manganese- catalyzed oxidation of aminopolyphosphonate is likely to be an important degradation mechanism in natural waters. 5.4. Degradation during oxidation processes Phosphonates present in natural waters may be subject to oxidation and disinfection processes during drinking water treatment. No information on the behavior of phosphonates during chlorination is avail- able. Ozonation of NTMP, EDTMP, and DTPMP resulted in the rapid disappearance of the parent compound in less than a minute [101]. 60–70% of the degraded phosphonate was found as phosphate; AMPA and phosphonoformic acid were also detected. The amine-free HEDP was degraded much more slowly with only 15% degradation after 30 min. The reaction path- way of EDTMP during ozonation is equivalent to that of EDTA [102]. The herbicide glyphosate was formed during ozonation of EDTMP with concentration of up to 10 nM [103]. The environmental fate, behavior and analysis of both AMPA and glyphosate has received considerable attention [10] and the formation of these compounds during ozonation of an aminopolypho- sphonate may change the risk analysis of these compounds considerably. 6. Speciation The speciation of chelating agents in the environment can be calculated based on the known stability constants of the metal–ligand complexes and the measured total concentrations of metals and chelating agents. This approach has been used to predict the speciation of EDTMP in Rhine water [6]. The simulated speciation was dominated by CuEDTMP and ZnEDTMP. HEDP was predicted to be mainly complexed with Ca and NTMP with Cu and Zn [104,105]. But how accurate are such calculations? There are several points to consider: In speciation calculations it is always assumed that equili- brium has been reached in the system. This is not always the case. Some metal complexes of aminocarboxy- lates have very slow exchange kinetics [106]. It has been found for example that Fe(III)EDTA is not in equilibrium with other metals in river water due to slow exchange kinetics of Fe(III)EDTA [107]. Almost nothing is known about the exchange kinetics of metal-phosphonate ARTICLE IN PRESS 0 20 40 60 80 100 120 0 100 200 300 400 500 no oxygen only Mn(II) Mn(II)/ 0.5 mM Ca Mn(II)/ 10 µM Zn % of inital NTMP time (minutes) Fig. 6. Oxidation of 10 mM NTMP in the presence of 10 mM Mn(II) in the presence and absence of dissolved oxygen and competing metal ions at pH 7.0. Reprinted with permission from [33]. Copyright (2000) American Chemical Society. B. Nowack / Water Research ] (]]]]) ]]]–]]] 9 complexes and therefore all equilibrium calculations have to be treated with care. Most calculations also do not consider that besides the chelating agent of interest other chelating agents and natural ligands are present in the water and com- pete for available metals. The interaction between the binding properties of phosphonates and fulvic acids is weak [108] but it has been shown that considering the natural ligands for Cu and Zn is critical for obtaining an accurate speciation of chelating agents [109]. In the following section a speciation model for three phosphonates is developed, based on a river water sample from Switzerland with well-known composition of metals, anthropogenic and natural ligands [110]. These ligands compete with the phosphonates for the same metals and have to be included in the speciation calculation. The concentration of the phosphonates in the calculations was set to 20 nM, comparable to EDTA at that location. The speciation was calculated for HEDP and NTMP with the constants from the IUPAC report [12] and for DTPMP with the constants from [111]. If only total metals and the phosphonates are taken into considera- tion, speciation is dominated by Cu for DTPMP, Ca for HEDP, and Ca, Mg, Zn and Cu for NTMP. Including EDTA and NTA does not change the speciation significantly; however, as soon as the natural ligands for Cu and Zn are considered, the calculated speciation for NTMP and DTPMP changes drastically. For NTMP the Cu and Zn complexes disappear totally due to the very strong binding of Cu to the natural ligands and CaNTMP and MgNTMP are dominant. For DTPMP the Ca and Mg complexes also become very important with more than 60% of the DTPMP complexed by these metals. CuDTPMP is only a minor species under these conditions. For HEDP the alkaline earth metals Ca and Mg are the major bound metals under all conditions. The fraction of other metal complexes is never above 0.1%. It can be concluded that phosphonates are most probably complexed to alkaline earth metals in natural waters. This calculation shows that considering the natural ligands is crucial for obtaining a reasonable result for phosphonate speciation (Table 2). Analytical methods have been developed to determine directly the speciation of aminocarboxylate chelating agents [112–114]. In principle these methods should also be applicable to phosphonates. A recent very promising method uses anion-exchange chromatography coupled to ICP-MS for the separation of metal-chelating agent complexes [35,36]. The method is also applicable to phosphonates and it has been shown that the CuEDTMP complex can be determined. The use of these methods to determine the speciation of phospho- nates in natural waters is needed. 7. Behavior during wastewater treatment The studies about the behavior of phosphonates during wastewater treatment can be divided into two groups: field studies with the addition of elevated concentrations of phosphonates to the influent of the treatment plant and investigations at ambient concen- trations. The elimination of phosphonates during wastewater treatment was found to be very high, even with high concentrations of added phosphonates of about 10 mM. Elimination of 9.7 mM HEDP in a field experiment was about 60% during the sedimentation and 90–97.5% during the biological step with simultaneous FeCl 3 precipitation [60]. Lower removal rates of 50–60% were found with the addition of 5–10 mM HEDP and 3–7 mM NTMP to a WWTP without iron-addition [115]. The behavior of 4.5–12 mM DTPMP was followed through the different treatment steps [39]. It was found that the DTPMP removal in the biological step was 95%. After the precipitation step with aluminum sulfate about 97% of the added DTPMP had been removed. This investigation has shown that even without simultaneous addition of iron or aluminum salts, very good removal in the biological step can be achieved. The second group of studies investigated the fate of phosphonates that are already present in the influent of the WWTP. For a 13-day field study a total amount of 117 mol of DTPMP was found in the influent of the WWTP compared to an effluent load of 17 mol, meaning that the removal efficiency was 85% [38]. Elimination of NTMP and EDTMP from another WWTP was at least 80% and 70%, respectively [38]. Because the concentration in the effluent was below the detection limit, this removal efficiency is the lower limit. ARTICLE IN PRESS Table 2 Calculated species distribution of HEDP, NTMP, and DTPMP in river water. Conditions: 20 nM phosphonates, 29.4 nM EDTA, 8.6 nM NTA and natural ligands for Cu, Zn and Ni Ca Mg Zn Cu % of total phosphonate HEDP No other ligands 88 12 0 0.1 With EDTA, NTA, natural ligands 88 12 0 0 NTMP No other ligands 33 25 11 28 With EDTA, NTA, natural ligands 55 42 0 0 DTPMP No other ligands 0 0 24 76 With EDTA, NTA, natural ligands 41 21 35 2 B. Nowack / Water Research ] (]]]]) ]]]–]]]10 [...]... environment Vom Wasser 2001;97:193–232 [5] Nowack B Environmental chemistry of aminopolycarboxylate chelating agents Environ Sci Technol 2002;36: 4009–16 [6] Gledhill WE, Feijtel TCJ Environmental properties and safety assessment of organic phosphonates used for detergent and water treatment applications In: Hutzinger O, editor The handbook of environmental chemistry, vol 3, Part F Berlin, Heidelberg: Springer,... no remobilization of metals by phosphonates is expected No biodegradation of phosphonate-chelating agents is observed in the environment The Fe(III)-complexes are rapidly photodegraded Rapid degradation of aminopolyphosphonates occurs in the presence of Mn(II) An analytical method for trace measurements in natural waters is urgently needed No analytical information on speciation of phosphonates in the... earlier versions of this manuscript and to Susan Tandy for editing the English This review was prepared in part during a stay at the University of Limoges, France The support of the Reinhold-Beitlich-Foundation, Tubingen, Germany, is greatly acknowledged References [1] Means JL, Alexander CA The environmental biogeochemistry of chelating agents and recommendations for the disposal of chelated radioactive... EDTA—Ethylenediaminetetraacetic acid In: Hutzinger O (Ed.), The Handbook of Environmental Chemistry, vol 3, Part F Berlin, Heidelberg: Springer, 1992 p 243–59 11 [3] Bucheli-Witschel M, Egli T Environmental fate and microbial degradation of aminopolycarboxylic acids FEMS Microbiol Rew 2001;25:69–106 [4] Knepper TP, Weil H Study on the entry of synthetic chelating agents and compounds exhibiting complexing... MD, Centner RL The development of diphosphonates as significant health care products J Chem Educ 1978;55:760–6 Weiss J, H gele G Ion-chromatographic analysis of a inorganic and organic complexing agents Fresenius Z Anal Chem 1987;328:46–50 Tsch bunin G, Fischer P, Schwedt G On the analysis of a polymethylenephosphonic acids I A systematic survey of the ion chromatography of organophosphonic acids Fresenius... Fischer P, Schwedt G On the analysis of a polymethylenephosphonic acids II A systematic survey of post-column derivatization in ion chromatography Fresenius Z Anal Chem 1989;333:117–22 Vaeth E, Sladek P, Kenar K Ion chromatography of polyphosphates and phosphonates Fresenius Z Anal Chem 1987;329:584–9 Tewari KMJ, van Stroe-Bieze SAM Analysis of aminecontaining phosphonates in detergent powders by anionexchange... Tway P Separation of organophosphonates by ion chromatography with indirect photometric detection J Liquid Chromatogr 1994;17:2511–31 Shamsi SA, Danielson ND Ribonucleotide electrolytes for capillary electrophoresis of polyphosphates and polyphosphonates with indirect photometric detection Anal Chem 1995;67:1845–52 Klinger J, Sacher F, Brauch H-J, Maier D Determination of organic phosphonates in aqueous... [46] Liu Y, Yu L, Guo J Adsorption of PBTCA on alumina surfaces and its influence on the fractal characteristics of sediments J Colloid Interface Sci 2000;227:164–70 [47] Day GM, Hart BT, McKelvie ID, Beckett R Influence of natural organic matter on the sorption of biocides onto goethite, II Glyphosate Environ Technol 1997;18: 781–94 [48] Nowack B, Stone AT Adsorption of phosphonates onto the goethite-water... Interface Sci 1999;214:20–30 [49] Nowack B, Stone AT Influence of metals on the adsorption of phosphonates onto goethite Environ Sci Technol 1999;3:3627–33 [50] Jung A, Bisaz S, Fleisch H The binding of pyrophosphate and two diphosphonates by hydroxyapatite crystals Calcif Tissue Res 1973;11:269–80 [51] Chirby D, Franck S, Troutner DE Adsorption of 153SmEDTMP on calcium hydroxyapatite Int J Radiat Appl... retention, release of polyphosphonates in oil and gas producing formations using surface complexation and precipitation theory Dissertation, Rice University, Texas, 1996 [66] Samakaev RK, Dyatlova NM, Dytyuk LT The solubility in water of the nitrilotrimethylenephosphonates of the group II elements Russ J Inorg Chem 1984;29: 1819–20 [67] Oddo JE, Tomson MB The solubility and stoichiometry of calcium-diethylenetriaminepenta(methylene . aim of this review is therefore to provide an overview of the current knowledge of the environmental chemistry of phospho- nates. It concentrates on polyphosphonates,. ]]]–]]] Review Environmental chemistry of phosphonates Bernd Nowack* Institute of Terrestrial Ecology (IT . O), Swiss Federal Institute of Technology Z . urich