Tài liệu Fundamentals of Machine Design P3 pptx

... or manufacture a product range. The range of operational speeds of a machine or the range of powers of a typical machine may be also as per a series of preferred numbers. Version 2 ... Kamalesh, Design of Machine Elements, Prentice Hall of India, New Delhi, 2003. 4. Chapman, W.A.J., Workshop Technology (part 2), ELBS, 4th edition, 1975 5. Maitra, G.M., Handbook of Design, ... other, the nature of fit is dependent on the limits of tolerances and fundamental deviations of the mating parts. The nature of assembly of two mating parts is defined by three types of fit system,...

13
583
0

Tài liệu Fundamentals of Machine Design P6 pptx

... strains may be derived in terms of these displacements. 2.3.2 Normal strains Consider an element AB of length δx ( figure-2.3.2.1). If displacement of end A is u, that of end B is uux∂+δ∂x ... discussed. 2.3.9 Reference for Module-2 1) Mechanics of materials by E.P.Popov, Prentice hall of India, 1989. 2) Mechanics of materials by Ferdinand P. Boer, E. Russel Johnson, J.T Dewolf, ... principal strains in terms of principal stresses as [][][]112322333121()E1()E1()Eε= σ−νσ+σε= σ−νσ+σε= σ−νσ+σ 1 From the point of view of volume change or dilatation...

11
491
0

Tài liệu Handbook of Machine Design P17 pptx

...

18
411
0

Tài liệu Handbook of Machine Design P15 pptx

...

21
354
0

Tài liệu Handbook of Machine Design P13 pptx

...

24
366
0

Tài liệu Fundamentals of Machine Design P1 pdf

... Discuss ‘factor of safety ‘ in view of the reliability in machine design. A.4: Reliability of a designed machine is concerned with the proper functioning of the elements and the machine as a ... Q.1: Define machine design. A.1: A machine is a combination of several machine elements arranged to work together as a whole to accomplish specific purposes. Machine design involves designing ... design, building design, process design, bridge design, clothing or fashion design and so on. Here we are concerned with machine design. We now define a machine as a combination of resisting bodies...

11
539
0

Tài liệu Fundamentals of Machine Design P2 ppt

... Module 1 Fundamentals of machine design Version 2 ME, IIT Kharagpur 2aσε(b) Plasticity- This is associated with the permanent deformation of material when the stress ... composition of 88% Cu, 10% Sn and 2% Zn. Brass is a Cu-Zn alloy with the typical composition of red brass of 85% Cu , 15% Zn. Q.6: List at least five important non-metals commonly used in machine design. ... atleast 5 important mechanical properties of materials to be considered in machine design. A.7: Some important properties of materials to be considered in design are: Elastic limit, yield and...

14
610
0

Tài liệu Fundamentals of Machine Design P4 pdf

... that the state of stress at a point can be given by six stress components only. It is important to understand the implication of this state of stress at a point in the design of machine elements ... cast iron machine parts of cross-sections shown in figure-2.1.7.2 are subjected to bending moments. Which of the two sections can carry a higher moment and determine the magnitude of the applied ... loaded brass strut hinged at both ends is 1m long and is of a square cross-section of sides 20mm. What should be the dimension of a steel strut of the same length and subjected to the same axial...

25
603
0

Tài liệu Handbook of Machine Design P27 pptx

...

39
301
0

Tài liệu Handbook of Machine Design P26 pptx

...

29
351
0