...
15
minutes
of
fire exposure. This may require fireproofing
of
the control
DESIGN AND CONSTRUCTION OF
LPG
INSTALLATIONS 3
4 Design
of
LPG
Vessels
4.1
APPLICABLE DESIGN CONSTRUCTION ...
Standards Body:
e
API 2510: Design and Construction of LPG Installations
49 CFR 195.205(b)(3)
American Petroleum Institute
22 API STANDARD 2510
flexibil...
... and Subtitle 5. Report Date
December 2009
6. Performing Organization Code
TECHNICAL MANUAL FOR
DESIGN AND CONSTRUCTION OF ROAD TUNNELS –
CIVIL ELEMENTS
7. Author(s)
8. Performing ... single-source technical
manual providing guidelines for planning, design, construction and rehabilitation of road tunnels, and
encompasses various types...
... Copy, â BSI
BS 5588- 4: 1978
ii
â BSI 01-1999
Foreword
This new code of practice was prepared under the direction of the Fire Standards
Committee.
In addition to the existing BS 5588- 1.1, BS 5588- 2, ... the release of the pressurizing air.
In buildings having an arrangement for the release of the pressurizing air that relies on the automatic
op...
... fire.
BS 5588, Fire precautions in the design and construction of buildings.
BS 5588- 1, Residential buildings.
BS 5588- 1.1, Code of practice for single-family dwelling houses
3)
.
BS 5588- 1.2, ... use of adhesive tape should not be relied upon for the long-term sealing of ducts.
The layout of the ductwork and the sizing of the main duct or...
... references
American Concrete Institute
307-69 Specification for the Design and Construction of
Reinforced Concrete Chimneys
307-88 Standard Practice for the Design and Construc-
tion of Cast-in-Place Reinforced ... Reinforced Concrete
Chimneys
318 Building Code Requirements for Structural
Concrete
505-54 Standard Specification for the Design and Con-
struct...
...
313R-1
This Commentary presents some of the considerations and assumptions of
ACI Committee 313 in developing the provisions of the Standard Practice
for Design and Construction of Concrete Silos and Stacking ... and curing
Chapter 4 Design, p. 313R-4
R4.1—Notation
R4.2—General
Commentary on Standard Practice for Design and Construction
of...
... 307-1
This standard gives material, construction, and design requirements for
cast-in-place and precast reinforced concrete chimneys. It sets forth mini-
mum loadings for design and contains ... p. 307-15
Design and Construction of Reinforced Concrete
Chimneys (ACI 307-98)
Reported by ACI Committee 307
ACI 307-98
David J. Bird
Chairman
Victor A. Bochicchio...
... areas and access
for delivery vehicles. The design and construction of concrete slabs for
parking lots and outside storage areas share many similarities with the
design and construction of streets ... Performance and Design of
GUIDE FOR DESIGN AND CONSTRUCTION OF CONCRETE PARKING LOTS 330R-21
Plain Concrete Pavement,” Highway Research Re...
... protection and curing
3.8—Lining and coating
Standard Practice for Design and Construction of Concrete Silos
and Stacking Tubes for Storing Granular Materials (ACI 313-97)
ACI 313-97
Mostafa H. ... con-
crete silos and stacking tubes for storing granular materials.
Silos for storing of ensilage have different requirements and
are no...
... 2—Materials, p. 373R-97-5
2.1 Concrete
2.2—Shotcrete and filler materials
2.3—Admixtures
Design and Construction of Circular
Prestressed Concrete Structures with
Circumferential Tendons
Reported by ... the
wall.
1.2—Objective
The objective of this report is to provide guidance in the
design and construction of circular prestressed concrete
structure...
... A—Recommendations and
considerations related to the design and
construction of tank foundations, p. 372R-20
CHAPTER 1—GENERAL
1.1—Introduction
The design and construction of circular prestressed concrete
structures ... concrete and prestressed concrete
design and construction given in ACI 318-99, ACI 350-01,
and ACI 301. Design and construction...
... 371R-5
3.1—General
3.2—Concrete
3.3—Formwork
3.4—Reinforcement
3.5—Concrete finishes
3.6—Tolerances
3.7—Foundations
3.8—Grout
Guide for the Analysis, Design, and Construction of
Concrete-Pedestal Water Towers
Reported ...
ASTM A 497 are permitted for reinforcement resisting other forces, and for shrinkage and temperature steel.
371R-1 5GUIDE FOR CONCRETE-PED...
...
B.11- Other factors
criteria
PREFACE
Concrete structures have been used in the North Sea and
other offshore areas of the world. With the rapid expansion of
knowledge of the behavior of concrete structures ... for consideration by the designer. The
design of offshore structures requires much creativity of the
designer, and it is intended that th...
... and use of FRP reinforcement, a
description of the unique material properties of FRP, and committee
recommendations on the engineering and construction of concrete reinforced
with FRP bars. The ... guide-
lines for reinforced concrete structures and provide
engineers and building officials with assistance in the speci-
fication, design, and...
... Design and Construction of
Externally Bonded FRP Systems for
Strengthening Concrete Structures
ACI 440.2R-02
Fiber-reinforced polymer (FRP) systems for strengthening concrete structures
have emerged ... as to
develop the strength of the FRP system. The development
length is a function of the strength of the substrate and the
rigidity of...