... RÁP M.TÍNH
CÀI WINDOW 98
CÀI WIN2000, XP
PARTION MAGIC
Sửa chữa ổ CD ROM
Nội dung : Sửachữa các bệnh thường gặp của ổ CD Rom .
SỬACHỮA CÁC BỆNH THƯỜNG GẶP CỦA Ổ CD -ROM
Bệnh 1 : Cửa ñĩa ... TÍNH
1/20/200http://www.hocnghe.com.vn/Phancung/Phancung.asp
TIỆN ÍCH GHOST
LAN - INTERNET
Dowload G.Trình
PHẦN S / CHỮA
Lấy ñĩa ra khi ñĩa bị kẹt
Tháo vỏ ổ ñĩa ra ñể có thể quan sát bộ cơ và bộ phận môtơ ra vào...
... Master hay Slaver thông việc
cắm Jumper ở vị trí nào trên sơ đồ Jumper Pins
(thông thường có hướngdẫn trên lưng ổ đĩa)
Ổ đĩa cứng
Ổ Power
Jumper
Ổ Data
1.5.4 Ổ CD-ROM-R/W-DVD
1.5.5 Ổ đĩa Mềm...
... flange, and gasket must be secure.
Never operate the device without a microwave
energy absorbing load attached.
Never look into an open waveguide or antenna
while the device is energized.
Gasket
ANTENNA
COOLING ... repaired:
(a) The interlock monitor switch is connected
correctly and firmly.
(b) The magnetron gasket is properly positioned
and mounted.
(c) The waveguide and the oven cavity are intact.
(no ... and
cavity. Never operate the magnetron unless it is
properly installed.
• Be sure that the magnetron gasket is properly
installed around the dome of the tube whenever
installing the magnetron.
Unlike...
... Exhaust gas temperature sensor
• Exhaust gas leaks in TOYOTA D-CAT
• Mass air flow meter
• Engine ECU
P2031
*1
Exhaust Gas Temperature Sensor Circuit
(Bank 1 sensor 2)
• Open or short in exhaust gas ... Circuit High
P0544
*1
Exhaust Gas Temperature Sensor Circuit
(Bank 1 Sensor 1)
• Open or short in exhaust gas temperature sensor (on up stream)
circuit
• Exhaust gas temperature sensor (on up ... (on down stream)
• Exhaust gas temperature sensor (on down stream)
• Engine ECU
P2032
*1
Exhaust Gas Temperature Sensor Circuit Low
(Bank 1 sensor 2)
P2033
*1
Exhaust Gas Temperature Sensor Circuit...
... bolts, nozzle leakage pipe and
twelve gaskets.
8. REMOVE INJECTION NOZZLES
(1PZ and 1HZ)
(a) (1PZ)
Using SST, remove the five injection nozzles, seats
and gaskets.
SST 09268-64010
(b) (1HZ)
Using ... ten bolts, seal washers, intake manifold
and five gaskets.
(c) (1 HZ and 1HD-T)
Remove the twelve bolts, seal washers, intake mani-
fold and six gaskets.
6. REMOVE WATER OUTLET
(a) (1HD-T)
Disconnect ... Remove the two nuts, water outlet and gasket.
7. REMOVE NOZZLE LEAKAGE PIPE
(1PZand1HZ)
(a) (1PZ)
Remove the five union nuts, nozzle leakage pipe and
five gaskets.
(b) (1HZ)
Remove the six union...