... of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus MB17SE LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... to perform the assembly procedure of the LCD monitor Asus MB17SE LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed ... is in power off status Prepare soft cloth and sponge as working platform to place LCD monitor horizontally Hold LCD by the side carefully and DON’T touch or press panel directly Remove all rings,...
... of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus MB19TU/SE LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... to perform the assembly procedure of the LCD monitor Asus MB19TU/SE LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed ... is in power off status Prepare soft cloth and sponge as working platform to place LCD monitor horizontally Hold LCD by the side carefully and DON’T touch or press panel directly Remove all rings,...
... the LCD monitor Be sure to use proper tools described in the previous chapter A SUS MM17T and MM19 SE/TE LCD monitor consist of various subsystem This section describes the procedures for LCD ... D M O D U L E L C D S U B S Y S T E M R E M O V A L II LCD Subsystem The illustrations below show how to remove the LCD panel from the LCD Subsystem A Removing Back Cover Remove screws Insert ... procedure for LCD monitor Be sure to use proper tools described in the first chapter SUS MM17T and MM19 SE/TE LCD monitor consist of various subsystem This section describes the procedures for LCD monitor...
... of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus MW221/201 LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... TAPE Release screws on PANEL FRAME 16 Separate LCD PANEL form BEZEL Loose screws on left and right side of LCD PANEL Separate PANEL FRAME from LCD PANEL 17 3.4 Bezel Subsystem Remove TAPE on ... to perform the assembly procedure of the LCD monitor Asus MW221/201 LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed...
... procedure of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus PG191 LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... Subsystem Remove screws Open latches along the edges of LCD BEZEL to dismount LCD PANEL 30 Remove screws on both sides Lift and dismount LCD SHIELDING Remove pieces of TAPE Disconnect LVDS CABLE ... to perform the assembly procedure of the LCD monitor Asus PG191 LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed...
... procedure of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus PW191 LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... to perform the assembly procedure of the LCD monitor Asus PM191 LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed ... sticker tapes to fix cables Assemble LCD panel and LCD SHIELDING 28 Tighten screws on both sides Locate panel module in BEZEL and press down to fix it Secure screws on LCD SHIELDING 29 4.2 Board Subsystem...
... procedure of the LCD monitor Depending on the failures, replace the defective parts accordingly Asus PW201 LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... to perform the assembly procedure of the LCD monitor Asus PM201 LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the detailed ... sticker tapes to fix cables Assemble LCD panel and LCD SHIELDING 38 Tighten screws on both sides Locate panel module in BEZEL and press down to fix it Secure screws on LCD SHIELDING 39 4.2 Board Subsystem...
... LAMP CABLE form the hole of LCD left BRACKET, and then assemble left BRACKET and LCD PANEL Assemble right BRACKET and LCD panel Tighten screws on both sides 22 Locate LCD in BEZEL and press down ... perform the assembly procedure of the LCD monitor Asus VW192 Series LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the ... the LCD monitor Depending on the failures, replace the defective parts accordingly Asus VW192 Series LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor...
... 3.3 LCD Subsystem The illustrations below show how to disassemble LCD Subsystem Separate LCD PANEL away from LCD BEZEL Lift KEY PAD vertically to dismount form BEZEL 17 Remove screws on LCD PANEL, ... following steps: 4.1 LCD Subsystem 4.2 Board Subsystem 4.3 Stand Subsystem 19 4.1 LCD Subsystem The illustrations bellow shows the assembly Procedure of LCD Subsystem Secure screws on LCD PANEL Mount ... perform the assembly procedure of the LCD monitor Asus MM17D series/MM19DE LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the...
... left and right speakers 14 3.3 Board & Panel Subsystem LCD Panel Remove screws on LCD Panel Slightly Lift the LCD panel from bottom of LCD PANEL, about 30 degrees 15 Unplug the LAMP CABLES carefully ... the LCD monitor Depending on the failures, replace the defective parts accordingly Asus PM17TU/TE/TA LCD Monitor consists of various subsystems This section describes the procedures for LCD monitor ... perform the assembly procedure of the LCD monitor Asus PM17TU/TE/TA LCD monitor consists of various subsystems This section describes the procedures for LCD monitor assembly In addition, the...
... cha ụ tụ 2.3 Sửachữa Nếu độ ô van độ côn vượt giới hạn cho phép phải sửachữa trục khuỷu cách mài cổ trục, cổ truyền theo kích thước sửachữa quy định (theo cốt sửa chữa) Mỗi cốt sửa chữa, đường ... thuật thực tế cổ trục cổ truyền mà sửachữa toàn sửachữa cổ truyền hay cổ trục không sửachữa riêng lẻ cổ trục hay cổ truyền Tất cổ trục cổ truyền phải sửachữa theo kích thước để đảm bảo cân ... để đánh bóng xi lanh để xác định kích thước sửachữa xi lanh theo cốt sửachữa Mỗi cốt sửachữa Sau doa xi lanh cần thay piston theo cốt sửa DH DT chữa tương ứng (có xét đến khe hở cần thiết...
... chơng trình Phân loại theo cấu điển hình máy : Nh máy ép trục khuỷu, máy cán ren, máy ép ma sát Theo cấu riêng biệt : Phanh, đảo chiều, cấu an toàn, bánh lệch tâm, 1.7 Nhu cầu lắp đặt sửachữa ... lắp sửachữa phục hồi chi tiết máy Nhu cầu phục hồi chi tiết máy bị h hỏng hay bị mài mòn sau thời gian vận hành Nhu cầu kiểm tra , bảo dởng máy, Nhu cầu bổ sung, trang bị mới, đại hoá trình...
... gồm trình : Quá trình anốt, trình catốt trình dẫn điện Quá trình anôt (xảy dơng cực) trình oxy hoá Ion kim loại chuyển vào dung dịch giải phóng điện tử Quá trình catốt (quá trình xảy cực âm) trình ... dụ : bi, côn xe đạp, ) 2.2.7 Tính sửachữaSửachữa tập hợp nguyên công có khả phục hồi tuổi thọ, phục hồi tính hoàn hảo, phục hồi khả làm việc máy Tính sửachữa thích ứng tính chất vật liệu ... định Giai đoạn h hỏng cần sửachữa phục hồi chi tiết máy để phục hồi khả làm việc kéo dài tuổi thọ máy 2.4 Sự h hỏng chi tiết máy Khi chế tạo, lắp ráp, vận hành sửa chữa, xảy h hỏng phần hay...
... Hệ thống sửachữa theo tiêu chuẩn Hệ thống sửachữa xem xét liên hoàn Sửachữa theo kế hoạch dự phòng ( bảo dỡng, sửachữa nhỏ, sửachữa vừa, sửachữa lớn (đại tu) a - Hệ thống sửachữa theo ... sửachữa hổn hợp - Về thời gian có : Sửachữa liên tục theo Sửachữa cấp tốc; sửachữa song song với công việc nguội khí lắp ráp 4.4 Tổ chức nơi sửachữa - Cố định phân xởng hay nhà máy sửachữa ... thuật trìnhsửachữa sản xuất yêu cầu Khả thiết bị có sở sửachữa máy 4.2.2 Phân loại hệ thống sửachữa [6, 21, 22] Hệ thống sửachữa theo nhu cầu (Sửa chữa đột xuất) Hệ thống sửachữa thay cụm...
... Hình - Sơ đồ tháo máy 5.4 Sơ đồ tóm tắt trìnhsửachữa máy : Kiểm tra sơ máy Lau bụi bậm & dầu mở Tiếp nhận máy vào sửachữa Di chuyển máy đến nơi sửachữa Tháo thành cụm ( Tháo phận) Tháo rời ... hồ sơ sử chữa cụm & chi tiết Chi tiết dùng đợc Chi tiết cần phục hồiChi tiết cần sửachữa loại bỏ Sửachữa chi tiết Kho chi tiết dự trữ Chi tiết Kiểm tra chất lợng chi tiết sau sửachữa Lắp ghép ... tắt trìnhsửachữa máy [6] 54 5.5 Làm máy chi tiết máy Quá trình chuẩn bị máy cho sửachữa bao gồm công việc : Làm sạch; Kiểm tra đánh giá sơ bộ; Xác định trạng thái máy để định phơng pháp sửa...
... hồi sửa chữa; Yêu cầu chất lợng sửa chữa; Các tiêu hiệu kinh tế việc phục hồi sửa chữa. (giá cả, khả làm việc, mua bán, 6.2 Phân loại phơng pháp chung phục hồi, sửachữa Phục hồi, sửachữa ... tố khác tiết có vài kích thớc sửa chữa, chí có kích thớc sửachữa Các chi tiết có kích thớc sửachữa thờng đợc chia loại : + Các chi tiết hệ lỗ : có kích thớc sửachữa thu nhỏ ( nh ổ trục ) + ... thớc sửachữa : Tăng lên nh xilanh, giảm nh cổ trục trục khuỷu Phơng pháp kích thớc sửachữa dùng để sửachữa chi tiết có mặt lắp ghép hình trụ, lắp ghép ren ốc, lắp ghép then Hiện kích thớc sửa...
... tan thụ động điện hoá anốt + trình giải phóng hydro + trình kết tủa kim loại tính chất lớp kim loại đợc kết tủa + thuỷ phân muối kim loại; + kết tủa hợp chất kiềm Khi trình mạ cần trì ổn định độ ... điện sấy khô; Ngâm chi tiết dầu bôi trơn ; Gia công nguội cần thiết; Doa đánh bóng theo cốt sửachữa xylanh 7.5 Mạ Crôm [8, 16] 7.5.1 Đặc điểm Theo lý thuyết crôm dễ bị ăn mòn sắt (Cr - 0,744V; ... tiết dầu bôi trơn T = 160 - 200 oC từ 1-2 ; Gia công nguội cần thiết ; Doa đánh bóng theo cốt sửachữa xylanh 7.6 Mạ ni ke Tính chất ni ken Ni ken có màu trắng bạc, Dẫn điện , dẫn nhiệt tốt,;...
... Là phơng pháp đặc trng cho sửachữa - phục hồi, phơng pháp suất cao, vùng ảnh hởng nhiệt nhỏ chu kỳ nhiệt xảy gián đoạn, sau hàn chi tiết gần nh không biến dạng Trong trình hàn có dùng chất Na2CO3 ... chất lợng mối hàn cao nhng phải tuân theo số quy trình công nghệ phụ ( ví dụ nung nóng sơ bộ, nhiệt luyện ) Thép có tính hàn hạn chế , cần có thêm trình công nghệ phụ nh nung nóng sơ , sử dụng ... mối hàn bình thờng 89 Thép có tính hàn kém, chất lợng mối hàn đạt chất lợng cao phải sử dụng trình công nghệ phụ Ngày khoa học kỹ thuật hàn phát triển mạnh nên tất kim loại thép hàn đợc đảm...