... loại WirelessRouter của các hãng như Linksys, Asus, Belkin, Buffalo Devices, Motorola và SiemensSau đây là ví dụ thực hiện trên Wirelessrouter Linksys model WRH54G.1. Tải Firmware cho Wireless ... Firmware cho Wireless router Đầu tiên chúng ta cần xác định xem thiết bị Wirelessrouter của bạn đã được hỗ trợ bởi firmware trên chưa. Để biết được điều này bạn cần xác định Wirelessrouter của bạn ... nâng cấp Firmware của Wireless router Bước 1: Bạn coi qua tài liệu của WirelessRouter hoặc xem trực tiếp trên thân thiết bị để tìm ra địa chỉ IP truy cập vào trang điều khiển Router cũng như tên...
... http://www.docstoc.com/docs/1849352/CAI-DAT -WIRELESS +++++++http://www.wimaxpro.org/forum/showthread.php?t=438Hướng dẫn cài đặt LINKSYS Wireless- G Broadband Router WRT54GSWRT54GS hỗ trợ một giải ... đề thi, đề cương, ôn tập, kiểm tra+++++++ - Để thiết lập bảo mật cho mạng không dây bạn chọn Wireless Security và lựa chọn một công nghệ mã hoá phù hợp với mạng của bạn (trong phần này chúng...
... ModeConfiguring a Router NameThis command works on both routers and switches.Configuring PasswordsThese commands work on both routers and switches. Router( config-subif)#Subinterface mode Router( config-line)#Line ... mode Router( config-line)#Line mode Router( config -router) # Router configuration mode Router& gt;Limited viewing of configuration. You cannot make changes in this mode. Router# You can see the configuration ... to verify the router congurationsã EXEC commands in configuration mode: the do command Router Modes Router& gt;User mode Router# Privileged mode (also known as EXEC-level mode) Router( config)#Global...
... network behind the hub router. The remote router can initiate connections to the hub router (it knows the end-point) but the hub router cannot initiate connections to the remote router (it does not ... 120!line con 0 transport input none Configuring Router- to -Router Dynamic-to-Static IPSec with NATIntroduction In this sample configuration, a remote router receives an IP address through ... Configuration Protocol (DHCP) and connects to a hub router. This configuration enables the hub router to accept dynamic IPSec connections. The remote router uses network address translation (NAT)...
... those steps on all routers in this lab assignment before continuing. Step 1 Login to the router in user exec mode a. Connect to the router and login. b. What prompt did the router display? __________________________________________________________________________ ... Step 2 Login to the router in privileged exec mode a. Enter enable at the user mode prompt. Router& gt;enable b. What prompt did the router display? 2 - 6 CCNA 2: Routers and Routing Basics ... The router is ready for the assigned lab to be performed. 6 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright 2003, Cisco Systems, Inc. Router Interface Summary Router...
... logoff by typing exit. Turn the router off. 1 - 6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright 2003, Cisco Systems, Inc. Lab 3.1.3 ConfiguringRouter Passwords Objective ... those steps on all routers in this lab assignment before continuing. Step 1 Login to the router in user EXEC mode a. Connect to the router and login. b. What prompt did the router display? __________________________________________________________________________ ... lab is produced from 1721 series routers. Any other router used may produce slightly different output. The following steps are intended to be executed on each router unless specifically instructed...
... Mạng 1 mà router B vừa mới nhận được. 3. Khi đó router A sẽ cập nhật lại là nó có thể gửi dữ liệu đến Mạng 1 thông qua router B. Router B thì định tuyến đến Mạng 1 thông qua router C. Router ... tương tự tiếp tục xảy ra ở router B,E. Khi đó, bất kỳ gói dữ liệu nào gửi tới Mạng 1 đều bị gửi lặp vòng từ router C tới router B tới router A tới router D rồi tới router C. 7.1.3. Định nghĩa ... một thông tin cập nhật cho router B và D thông báo là Mạng 1 đã bị ngắt. Tuy nhiên router C vẫn gửi cập nhật cho router B là router C có đường đến Mạng 1 thông tin qua router D, khoảng cách của...
... lệnh : ấu hình trên cả 2 con router ngoài cùng (edge router) trong n (transit area) ợc chuyển đến vùng backbone. a Sanjose1) ài cùng (edge router) trong Bài 1 : Configuring OSPF Virtual Link ... trung chuyển" (transit area) Code: SanJose1: ! router ospf 1 log-adjacency-changes area 51 virtual-link 192.168.3.1 (Đây là router s RID của Singapore) network 192.168.0.0 0.0.0.255 ... updates thì inter area traffic phải được vận chuyển thông đến vùng backbone Router Singapore là một ABR của vùng 3 , router SanJose1 là ABR của vùng 0 (backbone). Vì vậy , để hoàn thành mục đích...
... automatically, chọn This is a computer-to-computer(adhoc) network; wireless access points are not used. Nhấn Ok để quay lại bảng Wireless Networks và nhấn Ok một lần nữa để kết thúc.2 Lúc này ... • Trong Wireless Networks nhấn vào nút Add.• Trong Association, đặt tên cho mạng trong mục Network name,...