components operations and theory of hydraulic systems
Theory and design of CNC systems (Học CNC)
Ngày tải lên :
08/09/2013, 20:50
... Soft-NC is the scheduling that satisfies the execution of the software modules in real time Recently, NC systems have advanced from being closed systems to being open and distributed systems and ... invented the method of automatic control of the weaving of fabrics with a loom machine by using punch cards and this method was the beginning of the concept of NC The concept of NC was actually ... passing one slit of the rotation disk and one of the slits A, B, or Z on a fixed slit panel Slits A and B are arranged for a phase difference of 90 degrees and the electric signal of the output is...
- 466
- 856
- 4
Theory and Design of CNC Systems docx
Ngày tải lên :
27/06/2014, 06:20
... Soft-NC is the scheduling that satisfies the execution of the software modules in real time Recently, NC systems have advanced from being closed systems to being open and distributed systems and ... invented the method of automatic control of the weaving of fabrics with a loom machine by using punch cards and this method was the beginning of the concept of NC The concept of NC was actually ... passing one slit of the rotation disk and one of the slits A, B, or Z on a fixed slit panel Slits A and B are arranged for a phase difference of 90 degrees and the electric signal of the output is...
- 466
- 585
- 3
Design and Implementation of VLSI Systems_Lecture 04: Mos transistor Theory pdf
Ngày tải lên :
29/07/2014, 16:21
... OPERATION Current depends on region of transistor behavior For what Vin and Vout are nMOS and pMOS in Cutoff? Linear? Saturation? 41 NMOS OPERATION Cutoff Linear Saturated Vgsn < Vtn Vin ... LEAKAGE CURRENT: JUNCTION LEAKAGE AND TUNNELING Junction leakage: reverse-biased p-n junctions have some leakage Is depends on doping levels and area and perimeter of diffusion regions p+ n+ n+ p+ ... Vgs Vt cutoff V V V ds ds dsat Vds Vdsat linear saturation for pMOS 22 Covered ideal (long channel) operation (Shockley model) of transistor LECTURE 04: MOS TRANSISTOR THEORY Ideal...
- 58
- 320
- 0
Theory and Design of CNC Systems Part 14 potx
Ngày tải lên :
11/08/2014, 20:21
... ADCBI-type NCK – architecture, 211 address, 237 aging, 328 AGV, AIM, 404 and – AND, 260 and not – ANDN, 261 and stack – ANDS, 266 application layer, 275 approximation errors, 77 APT, 281 architecture ... function, 56 soft bus, 30, 416 soft PLC, 247–249 soft real-time system, 319 Soft-NC, 30, 248, 353, 355, 357, 359, 362–364, 366–369, 372–377, 388, 392, 393, 416 software model, 242 softwired NC, ... control, 164 derivative controller, 164 derivative gain, 164 design of PC-NC and open CNC, 353 design of system kernel, 361 development of the machining cycle, 305 device manager, 323 digital differential...
- 11
- 514
- 0
Theory and Design of CNC Systems Part 1 pps
Ngày tải lên :
11/08/2014, 20:21
... composed of two parts with a total of 11 chapters: Part I is composed of Chapters 1–6 on the principle and design of CNC, and Part II is composed of an open-architectural soft CNC system Specifically, ... invented the method of automatic control of the weaving of fabrics with a loom machine by using punch cards and this method was the beginning of the concept of NC The concept of NC was actually ... passing one slit of the rotation disk and one of the slits A, B, or Z on a fixed slit panel Slits A and B are arranged for a phase difference of 90 degrees and the electric signal of the output is...
- 35
- 560
- 2
Theory and Design of CNC Systems Part 2 doc
Ngày tải lên :
11/08/2014, 20:21
... Soft-NC is the scheduling that satisfies the execution of the software modules in real time Recently, NC systems have advanced from being closed systems to being open and distributed systems and ... commands for tool compensation, safety check, and skip Command the relative speed between tool and workpiece for interpolation command Command the spindle speed (RPM) Command tool change and ... Function commands for the simple control of a machine tool including relay/switch on and off as well as axis control (1) Coolant: command coolant on or off (2) Start/End of a main and sub program:...
- 35
- 581
- 1
Theory and Design of CNC Systems Part 3 ppsx
Ngày tải lên :
11/08/2014, 20:21
... system is the software module of the NCK unit that interprets the part program consisting of G&Mcode commands and related addresses such as S, T, and F The interpreter consists of a parser, an ... by the interpreter and is one of the key components of CNC, reflecting its accuracy In this chapter, the various software interpolators will be introduced and their strengths and weaknesses will ... software are used in modern CNC systems The concept of the software interpolator originates from that of the hardware interpolator and the hardware interpolator is limited to control simple systems...
- 35
- 821
- 1
Theory and Design of CNC Systems Part 4 potx
Ngày tải lên :
11/08/2014, 20:21
... number of the pulses from rough interpolation and Acc/Dec control at time i tipo is the iteration time of rough interpolation and N is the ratio of the iteration time of rough interpolation and ... Control systems in both hardware and software interpolation Regardless of the implementation manner, the algorithm itself is not different between hardware and software types In this textbook, the theory ... space and if u is ui and multiplicity of knot ui is k, P(u) can be differentiated as many as p − k times • The movement of control point Pi or the change of weight wi affects the portion of the...
- 35
- 405
- 0
Theory and Design of CNC Systems Part 5 potx
Ngày tải lên :
11/08/2014, 20:21
... result of X-axis interpolation and Acc/Dec control for two successive blocks In Fig 4.13, Block and Block are successive blocks and Fig 4.13a and Fig 4.13b show the interpolation result of Block and ... of various control modules that provide many functions Practically, however, the majority of CNC systems include control systems that consist of the interpolation module of the middle layer and ... Fig 4.18b, the lower of the two blocks’ speeds is defined as the speed at the corner For example, if the commanded feedrates of Block N1 and N2 are F1 and F2 , respectively, and F1 is higher than...
- 35
- 338
- 0
Theory and Design of CNC Systems Part 6 pptx
Ngày tải lên :
11/08/2014, 20:21
... distortion of table, and the characteristics of the servo system as well as dynamic errors due to high speed operation of the servo system, acceleration or deceleration operation, and the change of movement ... pos command(n)=10.0-real(n)*0.02; /Generation of position/ /command for simulation/ pos command (n+100)=8.0+real(n)*0.02; end / Position control loop / begin (n=1, 300) command= pos command (n); ... gains by the estimation of the dead time and time constant from Eqs 5.19 and 5.20, an ultimate gain and frequency are necessary to use the equation of the response curve of the Ziegler–Nichols...
- 35
- 432
- 0
Theory and Design of CNC Systems Part 8 ppsx
Ngày tải lên :
11/08/2014, 20:21
... values of the left operand and the middle operand and store the result to the right operand SUB 3, 1, Y3.1 When the input signal is ON, subtract the values of the left operand and the middle operand ... configuration and software of a Soft PLC, please read other references about Soft-NC and Open CNC systems 7.7 PLC Configuration Elements In this section, the configuration and execution structure of a PLC ... of the left operand and the value of the right operand are equal, set the specified bit as ON Otherwise, set the specified bit as OFF When the input signal is ON, if the value of the left operand...
- 35
- 416
- 0
Theory and Design of CNC Systems Part 9 potx
Ngày tải lên :
11/08/2014, 20:21
... openness and compatibility of PLC systems, hardware-based PLC systems have come to be replaced by software-based PLC, the so-called Soft PLC system A Soft PLC system is regarded as a software-oriented ... processor unit, memories, and auxiliary units AC and DC can be used for the input signal and output signal of a PLC system Various inputs and outputs, such as On/Off signals and timers/counters, can ... consists of alphanumerical input buttons and hot keys for executing the functions of CNC 8.1.3 Area for MPG Handling This area consists of the MPG (Manual Pulse Generator), the MPG handle ON/OFF switch...
- 35
- 409
- 0
Theory and Design of CNC Systems Part 10 pot
Ngày tải lên :
11/08/2014, 20:21
... kind of system call and usable hardware) The architecture of hardware (the number of CPUs and the way of connecting between modules) 315 316 CNC Architecture Design The architecture of the software ... reliability of the running tasks by preparing for occurrence of problems and removing them Real-time systems can be divided into two types: hard real-time systems and soft real-time systems In ... multi-programming theory As traditional examples of resource protection, airplane ticket reservation systems and bank accounting systems are often given Before a flight, the seats of an airplane...
- 35
- 353
- 0
Theory and Design of CNC Systems Part 11 pdf
Ngày tải lên :
11/08/2014, 20:21
... Hardware and Operating Systems In the case of the design of real-time systems, one of the key considerations is how to integrate the hardware components for equally distributing task load and how ... also called Soft-NC, and the functions of NC and PLC are designed as functional modules or software tasks in the multi-processing environment of a real-time OS Soft-NC has the aim of realizing ... The software modules of the CNC system consist of the OS and system kernel based on PC hardware and three key application modules, i.e NCK, MMC, and PLC Figure 10.2 shows an example of a software...
- 35
- 536
- 0
Theory and Design of CNC Systems Part 12 ppt
Ngày tải lên :
11/08/2014, 20:21
... only of stand-alone units but also FA systems Therefore, besides the development of special-purpose 392 10 Design of PC-NC and Open CNC systems by modularization of system components and standardization ... creating a thread and it receives the thread handler function and the initial status of the thread as arguments StartHandler, the third argument, denotes the name of the handler function and the fifth ... the event handler, first, the event handler should be taken and the status of the event object should be changed RtOpenEvent() plays the role of opening the handler of a particular event and receives...
- 35
- 368
- 1
Theory and Design of CNC Systems Part 13 pptx
Ngày tải lên :
11/08/2014, 20:21
... machining systems are envisioned to know and communicate their capabilities and condition to monitor and optimize their operations autonomously, to assess the quality of their output and to learn and ... goal of using STEP-NC and other standards to develop an open database of all the information necessary to design and manufacture a part While NIST understands the value of standards-based data exchange, ... cancel command is called Table A.3 G-code grouping Group Command One-shot command Feed command Constant surface speed command Absolute/Incremental programming command Mirror image command Feed...
- 35
- 372
- 1
Development of gradient smoothing operations and application to biological systems
Ngày tải lên :
09/09/2015, 18:58
... accurate, robust and efficient x List of Figures List of Figures Figure 2.1 Shape and weighting functions Figure 2.2 Illustration of construction of smoothing domain for 2D and 3D problems Figure ... 4.5 Comparison of condition number and iteration Table 5.1 Comparison of the PC-GSM, PL-GSM and αGSM Table 5.2 Errors and time consumed in different schemes Table 6.1 Fluid and soft disk properties ... (PL-GSM) and αGSM is the selection of smoothing function In the αGSM, the α value controls the contribution of PC-GSM and PL-GSM The accuracy and computational time of αGSM, PC-GSM and PL-GSM...
- 284
- 333
- 0
Tài liệu Integration and Automation of Manufacturing Systems pdf
Ngày tải lên :
22/12/2013, 20:17
... small handheld computers Development - software authoring 2.1.5 Advantages and Disadvantages A partial list of advantages and disadvantages is given below The cost, stability and open nature of the ... typed commands New users often prefer to use the system using the GUI Advanced users often prefer to use commands to administer the system, they are often faster and more reliable Commands can ... directories called ’.profile’ or ’.login’ These are used when a user logs Some of the standard Linux commands for files and directories are listed below Most of the file and directory names can...
- 593
- 515
- 1
Tài liệu 78 Rapid Design and Prototyping of DSP Systems docx
Ngày tải lên :
25/12/2013, 06:16
... process of MUX where bwtransmitting is the consumed bandwidth of transmitting packets, bwpassing is the consumed bandwidth of passing packets, bwecho is the consumed bandwidth of echo packets, and ... Gajski, D and Vahid, F., Specification and design of embedded hardware-software systems, IEEE Design & Test of Computers, pp 53-67, Spring 1995 [14] DeBardelaben, J and Madisetti, V., Hardware/software ... pushed until all software pieces come together In systems in which most hardware is simply commercial-off-the-shelf (COTS) parts, the time and cost of software prototyping and design can dominate...
- 39
- 554
- 0
Analysis and design of control systems using MATLAB
Ngày tải lên :
01/01/2014, 18:43
... application of MATLAB to the analysis and design of control systems Presentations are limited to linear, time-invariant continuous time systems Chapters and include a great number of worked examples and ... many systems of engineering, sciences, and in human body Some type of control systems affects most aspects of our day-to-day activities This chapter presents a brief introduction and overview of ... space-vehicle systems, aircraft autopilots and controls, ship and marine control systems, intercontinental missile guidance systems, automatic control systems for hydrofoils, surface-effect ships, and...
- 269
- 657
- 2