... detector and repair if neces-
sary
(2) Charge proper amount of re-
frigerant
(3) If indicated pressure value is
near 0 when connected to gauge,
create the vacuum after inspecting
and repairing the ... sure to read the following item carefully, then
follow the correct procedure described in the repair manual.
AC0M1–01
AC–36
–AIR CONDITIONING BLOWER UNIT
2518AuthorĂ: DateĂ:
DISASSEMBLY
1. REMOVE ... both hand
valves of manifold gauge set and stop the vacuum pump.
Check the system for leaks and repair necessary.
(e) Close both the high and low hand valves and stop the vac-
uum pump.
(f) Leave...
... bolt.
(c) Pry up the pipe with a screwdriver and remove the pipe.
8. REMOVE MANUAL VALVE BODY
Remove the 5 bolts and manual valve body.
9. REMOVE CONNECTOR CLAMP AND PIPE RETAINER
Remove the 2 ... PARK/NEUTRAL POSITION (PNP) SWITCH
AX–5
1925A uthorĂ: DateĂ:
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON–VEHICLE REPAIR
1. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
2. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) ... TRANSAXLE (A140E) DIFFERENTIAL OIL SEAL
AX–11
1904A uthorĂ: DateĂ:
DIFFERENTIAL OIL SEAL
ON–VEHICLE REPAIR
1. REMOVE LH AND RH DRIVE SHAFTS
(See page SA–17)
2. REMOVE SIDE GEAR SHAFT OIL SEAL
Using...
... to
another, thus controlling shifting and lock–up timing.
INTRODUCTION GENERAL REPAIR INSTRUCTIONS–
IN–4
GENERAL REPAIR INSTRUCTIONS
1. Use fender, seat and floor covers to keep the vehicle
clean ... the same time.
The component groups are inspected and repaired from the converter housing side.
As much as possible, complete the inspection, repair and assembly before proceeding to the next com-
ponent ... hammer and punch, drive out the pin.
(d) Slide out the shaft and remove the manual valve lever
from the case.
57. REMOVE MANUAL SHAFT OIL SEAL
Remove the oil seal with a screwdriver.
AUTOMATIC...
... Door lock manual switch OFF or UNLOCK No continuity
A1 – Ground Door lock manual switch LOCK Continuity
A2 – Ground Door lock manual switch OFF or LOCK No continuity
A2 – Ground Door lock manual ... No.1)
5. Wire Harness
–
–
–
BE–70
–
Door lock system does not operate by manual switch.
1. Power Window Master Switch
2. Door Lock Manual Switch
3. Integration Relay (I/P J/B No.1)
4. Wire Harness
BE–60
BE–70
BE–70
–
Door...
... lock manual switch OFF or UNLOCK No continuity
A16 – Ground Door lock manual switch LOCK Continuity
A17 – Ground Door lock manual switch OFF or LOCK No continuity
A17 – Ground Door lock manual ... No.1)
5. Wire Harness
–
–
–
BE–70
–
Door lock system does not operate by manual switch.
1. Power Window Master Switch
2. Door Lock Manual Switch
3. Integration Relay (I/P J/B No.1)
4. Wire Harness
BE–60
BE–70
BE–70
–
Door...
... the system with coolant.
z Use of improper coolants may damage engine cool-
ing system.
z Use Toyota Long life Coolant” or equivalent and
mix it with plan water according to the manufactur-
er’s ... between the ”LOW” and ”FULL” lines, when the engine is cold.
If low, check for leaks and add ’ Toyota Long Life Coolant” or Equivalent up to the ”FULL” line.
2. CHECK ENGINE COOLANT QUALITY
(a)...
... switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand–held tester.
OK:
Temperature value: –40°C (–40°F)
OK Repair or replace harness or connector.
NG
Check and replace ECM ... DateĂ:
1 Connect OBD II scan tool or TOYOTA hand–held tester, and read value of man-
ifold absolute pressure.
PREPARATION:
(a) Connect the OBD II scan tool or TOYOTA hand–held tester to the DLC3.
(b) ... ON and push the OBD II scan tool or TOYOTA hand–held tester main switch
ON.
CHECK:
Read value of the manifold absolute pressure on the OBD II scan tool or TOYOTA hand–held tester.
OK:
Same as...
... malfunctioning.
(f) TOYOTA Hand–Held Tester:
Conclude forced driving of the VSV for the EVAP.
(1) Stop the engine.
(2) Disconnect the TOYOTA hand–held tester from the
DLC3.
(g) If you have no TOYOTA Hand–Held ... the
purge line.
(c) TOYOTA Hand–Held Tester:
Forced driving of the VSV for the EVAP.
(1) Connect a TOYOTA hand–held tester to the DLC3.
(2) Start the engine.
(3) Push the TOYOTA hand–held tester ... of fuel for reduced
exhaust emissions
Remark: * For inspection and repair of the SFI system, refer to the SF section of this manual.
B01252
Air
Disconnect
Air Inlet Line Hose
B01253
Pinch
Push
AA
Pinch
B01148
B01149
Air
Purge...
... TO USE THIS MANUAL
IN–1
1AuthorĂ: DateĂ:
HOW TO USE THIS MANUAL
GENERAL INFORMATION
1. INDEX
An INDEX is provided on the first page of each section to guide you to the item to be repaired. To ... FI1066
IN0CO–04
Z11554
Seal Lock Adhesive
IN–4
–INTRODUCTION REPAIR INSTRUCTIONS
4AuthorĂ: DateĂ:
REPAIR INSTRUCTIONS
GENERAL INFORMATION
BASIC REPAIR HINT
(a) Use fender, seat and floor covers to keep ... replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly,...