Đang tải... (xem toàn văn)
Quản trị mạng
Nguyen Khac Quyet - Take Exam Exam questions Time remaining: 00: 06: 30 1 . What does a Catalyst 8500 use for Layer 3 switching? MLS MSFC NFFC CEF 2 . What can you use with the Catalyst 5000 to do multiprotocol routing? SRM RSM SAGE SAINT 3 . What do you do to configure MLS-SE to participate in MLS with an in-house RSM? MLS is enabled by default Enter the “set mls enable” command in privileged mode Enter the “set mls enable” and “set mls include rsm ip address” Commands in privileged mode Enter the “set mls enable” and “set mls vtp-domain vtp domain name” commands in privileged mode Enter the “set mls enable” and “set mls agingtime number-of-seconds” commands in privileged mode 4 . What are the three different flow masks that are supported by the MLS-SE? Destination-IP Source-Destination-IP IP-Flow IN-Flow 5 . What command would you use to see the flow mask type that is currently enabled on the MLS-SE? show flow show flow-mask show mls show mask 6 . What is true regarding Cisco’s NetFlow technology? Choose three. (Chi con 2 y thoi) Allows you to gather detailed information on your traffic flows Can only be used with extended access lists Allows for the deployment of access lists without any performance penalty when used in tandem with Multilayer Switching Requires a Layer 2 device to provide Layer 3 services 7 . A Supervisor Engine is not required for the 6x00 series of switches. True False 8 . The required components of Cisco Systems MLS implementation are: (Choose three). The MLS-SE The MLS-RP The MLS-PR The MLSP 9 . Read and answer the question A B C D 10 . If you had two Telnet sessions occurring between two PC’s, why would these sessions be treated as two different traffic flows within MLS cache even though the Layer 3 addressing is the same? The source port numbers would be different The MLS-RP would change the IP addresses to MAC addresses The MLS-PR converts the IP addresses to different traffic flows The default gateway would age out all entries to make room for new entries 11 . What are three advantages of Multilayer switching? Combines functionality of Layer 2, Layer 3, and Layer 4 switching High-speed functionality Switching is software-based Low latency 12 . What is true regarding MLS cache? Bidirectional flow Knows data flows Two-way flow Unidirectional flow 13 . Cisco defines a traffic flow as a set of packets between a specific source and destination where the protocol and the port numbers are different. True False 14 . What command would you use to add an interface to a new VTP domain on an RP (Route Processor)? mls rp mls vtp-domain mls rp vtp-domain mls ip rp 15 . Layer 4 switching has better performance than Layer 3 switching. True False 16 . What daughter card for the 6x00 series of switches is similar to the RSFC that is used in the 5000 series of switches? MSFC RSM NFFC MSM 17 . What are the three basic types of packets? Unicasts Local Broadcasts Multicasts Remote Broadcasts 18 . What is the purpose of defining an MLS Management Interface? To disable MLS To allow MLS to function To stop the flow of MLSP packets To prevent overruns 19 . Read and answer the question A B C D E F 20 . What are two ways that Cisco routers can control traffic based on Layer 4 information? Extended access lists Standard access lists Layer 4 accounting using Fast switching Layer 4 accounting using NetFlow switching 21 . For Layer 3 switching to work, the MLS-SE must see the traffic flow: in only one direction from the MLS-SE in only one direction from the MLS-RP in both directions from the MLS-RP in both directions from the MLS-SE 22 . What command would you use to allow input access lists? mls rp ip input-acl mls ip rp input-acl mls ip input-acl mls rp input-acl 23 . The first module in the Catalyst 5000 switches: should contain at least 12 Ethernet ports is not required to be utilized contains an interface module contains the console port in the Supervisor Engine 24 . What is true regarding the RSFC (Route Switch Feature Card)? Choose two. It is a full function IOS router installed as an integrated daughter card It is used on the Catalyst 5000 series Supervisor IIG and Supervisor IIIG Engines Can only be used on the Supervisor II Engine Can only be used on the Supervisor III Engine Showing page 1 of 1 : 1Go! © 2004 HanoiCTT. All rights reserved. . participate in MLS with an in-house RSM? MLS is enabled by default Enter the “set mls enable” command in privileged mode Enter the “set mls enable” and “set mls. required components of Cisco Systems MLS implementation are: (Choose three). The MLS- SE The MLS- RP The MLS- PR The MLSP 9 . Read and answer the question