Đang tải... (xem toàn văn)
Tài liệu nói về Biến Tần INVT CHV190 -Tài liệu viết bằng tiếng anh nguyên bản -mô tả chi tiết bằng hinh ảnh về Biến Tần INVT CHV190 -mô tả về cách sản xuất Biến Tần INVT CHV190 -mô tả cách sử d
CHV190 series special inverter for crane - 1 - Contents Contents .1 SAFETY PRECAUTIONS 4 1. INTRODUCTION 5 1.1 Technology Features 5 1.2 Description of Nameplate .6 1.3 Selection Guide 6 1.4 Parts Description 8 1.5 Description of Extension Card .9 2. UNPACKING INSPECTION .10 3. DISASSEMBLE AND INSTALLATION 11 3.1 Environmental Requirement 11 4. INSTALLATION AND COMMISSIONING 13 4.1 Connections of Peripheral Devices .14 4.2 Terminal configuration 15 4.3 Typical Wiring Diagram 17 4.4 Wiring the Main Circuits .18 4.5 Wiring Control Circuit Terminals 20 4.6 Installation Guidline to EMC Compliance 22 5. OPERATION 26 5.1 Operating Keypad Description .26 5.2 Operation Process 28 5.3 Running State .30 6. DETAILED FUNCTION DESCRIPTION 32 6.1 P0 Group--Basic Function 32 6.2 P1 Group--Speed Curve .39 6.3 P2 Group--Motor Parameters 43 6.4 P3 Group--Vector Control 47 6.5 P4 Group--Encoder 52 6.6 P5 Group--Input Terminals .53 6.7 P6 Group--Output Terminals 59 6.8 P7 Group--Display Interface 64 6.9 P8 Group--Enhanced Function 69 6.10 P9 Group--Protection Parameters .79 6.11 PA Group--Serial Communication 84 CHV190 series special inverter for crane - 2 - 6.12 Pb Group--Master-Slave Control Group 88 6.13 PC Group--Motor Parameters 1 .96 6.14 Pd Group--Profibus Communication 100 6.15 PE Group--Factory Setting .104 6.16 PF Group--Motor Parameters 2 .104 6.17 PP Group--Motor Parameters 3 .108 7. DESCRIPTION OF CHV190’S EXTENSION CARD 114 7.1 Description of I/O Extension Card .114 7.2 Description of Asynchronous PG Card 115 7.3 Description of Synchronous PG Card 119 7.4 Description of Modbus Communication Card 121 7.5 Description of Profibus Communication Card .123 7.6 Ethernet Communication Description 140 8. TROUBLE SHOOTING 141 8.1 Fault and Trouble Shooting 141 8.2 Common Faults and Solutions .146 9. MAINTENANCE .148 9.1 Daily Maintenance 148 9.2 Periodic Maintenance .149 9.3 Replacement of Wearing Parts 150 10. COMMUNICATION PROTOCOL 151 10.1 Interfaces 151 10.2 Communication Modes 151 10.3 Protocol Format 151 10.4 Protocol Function .152 10.5 Notice 157 10.6 CRC Check .157 10.7 Example 158 APPENDIX A APPLICATION MODE DESCRIPTION .164 A.0 Open loop sequence 164 A.1 Close loop sequence .165 APPENDIX B APPLICATION MODE DESCRIPTION 167 B.0 General Application Mode .167 B.1 Operating Lever Mode .167 B.2 Remote Control Mode 169 CHV190 series special inverter for crane - 3 - B.3 Hierarchical Operating Lever Mode 170 B.4 Hierarchical Remote Control Mode .171 B.5 Electric Potential Mode 173 B.6 Master-slave Power Equilibrium Host Mode .174 B.7 Master-slave Power Equilibrium Slave Mode .178 B.8 Master-slave Speed Synchronization Host Mode .179 B.9 Master-slave Speed Synchronization Slave Mode .182 APPENDIX C THE SELECTION GUIDE OF CHV190 .184 C.1 Inverter Capacity Calculation 184 C.2 Renewable Energy Treatment .185 APPENDIX D RELATIVE DIMENSION OF INVERTER .189 D.1 External Dimension 189 D.2 Dimensions of External Keypad 190 D.3 Installation Space .191 D.4 Disassembly .192 APPENDIX E SPECIFICATIONS OF ACCESSORIES .193 E.1 Specifications of Breaker, Cable, Contactor and Reactor 193 APPENDIX F FUNCTON PARAMETERS .196 123doc.vn