Đang tải... (xem toàn văn)
Tài liệu Shop Manual & ETM BCM KIA Cerato 2010
2010 > G 1.6 DOHC > Body Electrical System SpecificationsItem SpecificationRated voltage DC 3VService voltage range DC 2.5V ~ 3.2VTemperature range -4°F ~ 140°F (-20°C ~ +60°C)Storage temperature range -22°F ~ 176°F (-30°C ~ +80°C)Modulation method FSKKeyless entry transmitterPower source Lithium 3V battery (1EA)Transmissible distance 30m or moreLife of battery 2 years or more (at 20 times per day)Button 4 (Door lock, Door unlock, Trunk, Panic)Transmission frequency 433.92 MHz 2010 > G 1.6 DOHC > Body Electrical System Component LocationLanguageLanguage 1. Trunk lid actuator & switch2. Rear door switch3. Body control module4. Key warning switch5. Front door switch6. Front door lock actuator & switch7. Rear door lock actuator & switch 2010 > G 1.6 DOHC > Body Electrical System DescriptionKeyless Entry SystemThe burglar alarm system is integrated with the keyless entry system. The keyless entry system allows you to lock and unlock the vehicle with the remote transmitter. When you push the LOCK button, all doors lock. When you push the UNLOCK button again, all doors unlock.The room lamp, if its switch is in the center position, will come on when you press the UNLOCK button. If you do not open a door, the light will go off in about 30 seconds, the doors will automatically relock, and the burglar alarm system will rearm. If you relock the doors with the remote transmitter within 30 seconds, the light will go off immediately.You cannot lock or unlock the doors with the remote transmitter if the key is in the ignition switch.The system will signal you when the doors lock and unlock by flashing the hazard lamp once when they lock and closed, and twice when they unlock.FunctionKeyless Entry FunctionDOOR LOCK / UNLOCK and Trunk operations are performed with remocon1. Keyless entry function is performed in a state that key in switch is eliminated from key cylinder2. LOCK / UNLOCK and trunk signals are received from the transmitter and DOOR LOCK / UNLOCK and Trunk signals are output.3. In case of tailgate, this operation is performed when pushing the button for 0.5s or more.Transmitter(TX) Spec1. Transmission Distance : 30m or more from outside of the car2. Registration procedure of the transmitter(1) In registration mode, it shall be possible to register up to Max 4EA.(2) At re-registration, data are registered newly after deleting the previous TX DATALanguage (3) For the registration procedures by using Hi-scan tool, refer to "TRANSMITTER CODE REGISTRATION".3. Transmitter signal & Receiver Spec(1) Transmission signalB. 2010 > G 1.6 DOHC > Body Electrical System InspectionFront Door Lock Actuator1. Remove the front door trim.(Refer to the Body group - Front door)2. Remove the front door module.(Refer to the Body group - Front door).3. Disconnect the connectors from the actuator.[LHD]Language [RHD]4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.Rear Door Lock Actuator1. Remove the rear door trim.(Refer to the Body group - Rear door) 2. Remove the rear door module.(Refer to the Body group - Rear door)3. Disconnect the connectors from the actuator.[LHD][RHD]4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily. Trunk lid Lock Actuator Inspection1. Remove the trunk trim. (Refer to the Body group - trunk)2. Disconnect the 3P connector from the actuator.3. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.Front Door Lock Switch1. Remove the front door trim.(Refer to the Body group - Front door)2. Remove the front door module.(Refer to the Body group - Front door).3. Disconnect the connectors from the actuator.[LHD] [RHD]4. Check for continuity between the terminals in each switch position when inserting the key into the door according to the table.Rear Door Lock Switch1. Remove the rear door trim.(Refer to the Body group - Rear door) 2. Remove the rear door module.(Refer to the Body group - Rear door)3. Disconnect the connectors from the actuator.[LHD][RHD]4. Check for continuity between the terminals in each switch position according to the table. Trunk lid Switch1. Remove the trunk trim. (Refer to the Body group - Trunk)2. Disconnect the 3P connector from the actuator.3. Check for continuity between the terminals in each switch position according to the table.Door SwitchRemove the door switch and check for continuity between the terminals. [...]...Key In Switch 1 Remove the crash pad lower panel (Refer to Body group-Crash pad) 2 Disconnect the 6P connector from the key warning switch (A) 3 Check for continuity between the terminals in each position according to the table 2010 > G 1.6 DOHC > Body Electrical System Language Inspection 1 Check that the red light flickers when the door lock or . lock actuator & switch7. Rear door lock actuator & switch 2010 > G 1.6 DOHC > Body Electrical System DescriptionKeyless Entry SystemThe. 3.2VTemperature range -4 °F ~ 140°F (-2 0°C ~ +60°C)Storage temperature range -2 2°F ~ 176°F (-3 0°C ~ +80°C)Modulation method FSKKeyless entry transmitterPower