Đang tải... (xem toàn văn)
Nghệ Thuật Gấp Giấy_ Gấp 1 CHIẾC XE MÁY YZR_M1_ YAMAHA rất đẹp trong mắt người bạn yêu thương. fie dạng pdf hướng dẫn rất cụ thể, tỉ mỉ và chỉ dẫn các cách để bạn cắt và gấp giấy
Thank you for downloading the "YZR-M1"paper craft model By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble an authentic-looking replica of the YZR-M1 Assembly instructions: Fourteen A4-sized sheets Paper craft: Eighteen A4-sized sheets with 114 parts in all These instructions apply only to the "YZR-M1." These Paper Craft parts are easier to work with when printed out on strong, thick paper (like postcard stock) In creating these Paper Craft models we use 110kg Kent paper stock 2006.4.17 Basic working method and markings To begin Tools and materials needed -Ruler - scissors - blade cutter or "Exacto-knife" - awl or other pointed tool (for making a folding crease) - felt pen Solid lines - pin set - glue - hand towel ( for cleaning your fingers) dictionary or other heavy book ( to press the papers flat) Fold along these lines The printed surface should be on the outside of the folded shape Items of Caution *Take care when using sharp or pointed objects or when using bladed cutting tools Place a heavy sheet of paper under the paper you want to cut *Use glue and other adhesives only in well-ventilated areas *When printing, use a slightly reduced font size There may be differences in dimensions, depending on the type of printer used Broken lines Fold along these lines The printed surface should be on the inside of the folded shape Dotted line How to assemble Cut along these lines *Follow the working method and markings carefully *Cut carefully along the outter line with cutting blade, Exacto-knife or scissors One - point Advice Do not fold or cut the parts marked *Cut carefully with cutting blade, Exacto-knife or scissors *For folding parts, first use an awl or other pointed tool to make a light crease along the dotted or solid line This will make the folds straight Avoid making strong creases, as this will cause the paper to tear Cut out parts marked with an asterisk(*) *As an adhesive, white wood glue is recommended Avoid over application as this may cause the paper to wrinkle *Before beginning assembly, test adhesive amounts on extra paper *Occasionally, white spots will be apparent on folds and cuts Use a marker or pencil to fill in these spots It is recommended that this be done after each stage of assembly because coloring becomes more difficult once parts are assembled Red dots are the reference positions for gluing surfaces Assembling the Front Cowl First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Front Cowl Fold each relevant part according to the assembly symbols Sheet A, parts in total Please use the Glue dots on each component as reference when gluing surfaces A-2 A-1 A-5 A-3 Reference photo A-4 A-2 Assembling the Steering First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Steering Fold each relevant part according to the assembly symbols Sheet B, 18 parts in total Please use the Fold or Curve Glue dots on each component as reference when gluing surfaces B-1 B-2 B-4 [ Upper Steering Column ] B-3 B-11 B-6 B-10 B-9 B-7 *DO NOT glue the upper and the lower parts [ Lower Steering Column ] of the steering column at this stage B-5 B-8 B-14 B-13 B-16 B-18 B-15 B-17 Reference photo B-12 Assembling the Fuel Tank & Exhaust Pipes First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Fuel Tank Fold each relevant part according to the assembly symbols Sheet C, parts in total Please use the Glue dots on each component as reference when gluing surfaces C-2 Reference photo C-1 Exhaust Pipes Fold each relevant part according to the assembly symbols Sheet D, parts in total Please use the dots on each component as reference when gluing surfaces D-4 D-5 D-6 D-1 D-3 Reference photo D-2 Assembling the Rear Fender First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Rear Fender Fold each relevant part according to the assembly symbols Sheet E, 12 parts in total Please use the Fold or Curve Glue dots on each component as reference when gluing surfaces E-9 E-2 E-10 E-8 E-3 E-1 E-11 E-4 E-5 E-12 E-7 Reference photo E-6 Assembling the Under Cowl First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Under Cowl Fold each relevant part according to the assembly symbols Sheet F, 10 parts in total Please use the Glue dots on each component as reference when gluing surfaces F-4 F-5 F-7 F-2 F-3 F-6 F-10 F-9 F-8 F-1 Reference photo Assembling the Frame First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Frame Fold each relevant part according to the assembly symbols Sheet G, 21 parts in total Please use the Glue dots on each component as reference when gluing surfaces G-2 G-1 G-13 G-4 G-8 G-6 G-10 G-15 G-7 G-17 G-9 G-14 G-16 G-11 G-5 G-12 G-18 G-20 G-3 G-21 G-19 Reference photo Assembling the Rear Arm First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Fold or Curve Rear Arm Fold each relevant part according to the assembly symbols Sheet H, 13 parts in total Please use the Glue dots on each component as reference when gluing surfaces H-2 H-5 H-11 H-6 H-13 H-1 H-12 H-4 H-10 H-3 *Do not glue Parts H-3 to H-4 at this stage H-9 H-8 H-7 Reference photo Assembling the Front Tire First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Front Tire Fold each relevant part according to the assembly symbols Sheet I, 14 parts in total Please use the Fold or Curve Glue dots on each component as reference when gluing surfaces *Glue the completed front wheel to the assembled front tire I-12 Front Tire I-14 I-5 I-13 I-11 I-4 Front wheel I-6 I-7 I-3 I-2 Reference photo I-10 I-9 I-8 I-1 10 Assembling the Rear Tire First, assemble each component by following the working method and markings Then, refer to the illustration and photos below to glue the parts together Indication of Working Methods Rear Tire Fold each relevant part according to the assembly symbols Sheet J, 12 parts in total Please use the Fold or Curve Glue dots on each component as reference when gluing surfaces *Glue the completed rear wheel to the assembled rear tire J-10 J-12 Rear Tire J-3 J-11 J-9 J-2 J-4 Rear wheel J-5 J-1 Reference photo J-8 J-6 J-7 11 10 Finish Please use the Frame dots on each component as reference when gluing surfaces Assembly Instructions Fuel Tank Rear Fender Upper Steering Column glue the assembled parts in numerical order through 12 Glue the Rear Tire to the Rear Arm Front Cowl Glue the Rear Arm to the Frame Glue H-3 to H-4 Exhaust Pipes 12 10 Glue H-3 to the Frame H-4 Glue the Rear Fender to the Fuel Tank 12 Glue the Fuel Tank to the Frame 10 Glue the Under Cowl to the Front Cowl Glue the Under Cowl to the Frame Glue the upper part of the Steering to the Frame 10 Glue the lower part of the Steering to the upper part of the Steering and the Frame 11 Glue the Front Tire to the lower part of the Steering Lower Steering Column Rear Tire 12 Finish by gluing the Exhaust to the Rear Arm and the Rear Fender Rear Arm H-3 11 Front Tire Under Cowl 12 11 Assembled Model and the List of Parts Please refer to the photo below when attaching each component RIGHT Rear Fender Fuel Tank Front Cowl E-1 E-6 E-11 C-1 A-1 E-2 E-7 E-12 C-2 A-2 E-3 E-8 A-3 E-4 E-9 A-4 E-5 E-10 A-5 FRONT Exhaust Pipes Steering D-1 B-1 B-6 B-11 B-16 I-1 I-6 I-11 D-2 B-2 B-7 B-12 B-17 I-2 I-7 I-12 D-3 B-3 B-8 B-13 B-18 I-3 I-8 I-13 D-4 B-4 B-9 B-14 I-4 I-9 I-14 D-5 B-5 B-10 B-15 I-5 I-10 D-6 13 Front Tire 12 Assembled Model and the List of Parts Please refer to the photo below when attaching each component LEFT Frame G-1 G-6 G-11 G-16 G-21 G-2 G-7 G-12 G-17 G-3 G-8 G-13 G-18 G-4 G-9 G-14 G-19 G-5 G-10 G-15 G-20 REAR Under Cowl Rear Arm F-1 F-6 H-1 H-6 H-11 J-1 J-6 J-11 F-2 F-7 H-2 H-7 H-12 J-2 J-7 J-12 F-3 F-8 H-3 H-8 H-13 J-3 J-8 F-4 F-9 H-4 H-9 J-4 J-9 F-5 F-10 H-5 H-10 J-5 J-10 Rear Tire 14 ... G-2 G-7 G -1 2 G -1 7 G-3 G-8 G -1 3 G -1 8 G-4 G-9 G -1 4 G -1 9 G-5 G -1 0 G -1 5 G-20 REAR Under Cowl Rear Arm F -1 F-6 H -1 H-6 H -1 1 J -1 J-6 J -1 1 F-2 F-7 H-2 H-7 H -1 2 J-2 J-7 J -1 2 F-3 F-8 H-3 H-8 H -1 3 J-3 J-8... E-8 A-3 E-4 E-9 A-4 E-5 E -1 0 A-5 FRONT Exhaust Pipes Steering D -1 B -1 B-6 B -1 1 B -1 6 I -1 I-6 I -1 1 D-2 B-2 B-7 B -1 2 B -1 7 I-2 I-7 I -1 2 D-3 B-3 B-8 B -1 3 B -1 8 I-3 I-8 I -1 3 D-4 B-4 B-9 B -1 4 I-4 I-9... G, 21 parts in total Please use the Glue dots on each component as reference when gluing surfaces G-2 G -1 G -1 3 G-4 G-8 G-6 G -1 0 G -1 5 G-7 G -1 7 G-9 G -1 4 G -1 6 G -1 1 G-5 G -1 2 G -1 8 G-20 G-3 G- 21 G -1 9