CATIA Part Design Exercicios TRV5PD TRV5PD (Exercicios) – Página Maiores Informações: NV Sistemas Ltda Rua Cotoxó, 611 - Sala 44 05021-000 São Paulo SP Tel: (0XX) 11 3675-2799 Fax: (0XX) 11 3676-1363 www.nvsistemas.com.br Esta publicação é parte integrante conjunto de treinamentos oferecidos pela NV Sistemas e não pode ser vendida separadamente Julgamos que as informações contidas nesta publicação sejam exatas, entretanto, a NV Sistemas não assume nenhuma responsibilidade pelo seu uso As informações estão sujeitas a alterações sem aviso prévio e não devem ser interpretadas como um compromisso da NV Sistemas CATIA é marca registrada da Dassault Systèmes S A Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Table of Contents Piston Creating the Main Pad Creating the Symmetrical Cut-out .7 Creating the Cylindrical Boss 13 Creating Pockets 14 Creating a Through Hole 17 Creating Fillets 19 Changing the color .25 Angle Bracket 27 Setting Part Design Parameters 28 Defining the Pads for the Bracket .28 Defining the Pilot Holes and the Angular Pads for the Bracket 32 Defining the Clevis Through Hole and Fillets 36 Building the Hinge 37 Car Jack Support 48 Creating Profiles and Pads 50 Creating Draft Angles 53 Creating Edge Fillets 55 Creating Additional Profiles and Pads 57 Creating Edge Fillets for the Additional Pads .60 Creating Holes 62 Creating Grooves .83 Creating a Chamfer .86 Creating Pockets 88 Creating Edge Fillets .91 Side Toolhead .93 Creating Profiles, Pads and Draft Angles 95 Creating Pockets and Draft Angles 97 Creating Profiles, Pads and Draft Angles 103 Creating Holes 106 Creating Pockets 119 Creating Fillets 122 Creating Chamfers 127 Tee Fitting 129 Creating Pads 130 Draft Angles and Fillets 140 Holes Creation 144 Mirroring 151 Mold Core: Shaft Creation 154 Mold Core: Filleting 158 Mold Core: Shaft Creation 159 Mold Core: Filleting 161 Removing Body 162 Meat Mincer Screw 164 Creating Profiles and Helixes 165 Creating a Loft 180 Creating Tri-Tangent Fillets 182 Creating Variable Radius Fillets .185 Creating a Pad 188 Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Creating a Groove 191 Creating a Pad 201 Creating a Hole .203 Creating a Chamfer 206 Pedal Support 207 Rib Creation 209 Circular Pattern .212 Tri-Tangent Fillets 213 Filleting .215 Rib Creation 219 Filleting .222 Pad Creation 225 Filleting .228 Hole Creation 235 Circular Pattern .240 Threaded Hole Creation 241 Assembling the Crank Set 244 Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Piston We will design this Piston to practice the various ways of using both the Sketcher and Part Design workbenches for designing parts Load the starting piston part from the companion, and if necessary, activate Start + Mechanical Design + Part Design (DO NOT DO IT IF YOU ARE ALREADY IN THE PART DESIGN WORKBENCH) Creating the Main Pad In this section, we are going to build the main pad Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Now, let us it ! Select the Pad icon Select the sketch to be extruded Enter the following parameters in the dialog box, and then select OK You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Creating the Symmetrical Cut-out In this section we are going to build the symmetrical cut-out We are going to insert a body in which we are going to create a pad and its symmetric Select Insert + Body Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página Select the Sketcher icon Select the ZX plane Select the Profile icon Sketch approximately the following profile Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 9 Using the constraint icon, constrain the profile as shown here after 10 Select the Exit icon to leave the Sketcher 11 Using the Pad icon, create a pad with the following parameters You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 10 12 In order to get the symmetrical pad, select the Mirror icon 13 Select the YZ plane 14 Select OK in the dialog box You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 237 Select the following face Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 238 Enter the following parameters in the Hole dialog box, then, select OK Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 239 You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 240 Circular Pattern In this section, we are going to duplicate the hole using the Circular Pattern command , and then select the previously created hole As the Activate the Circular Pattern icon Reference Element, select the XY plane Enter the following parameters in the Circular Pattern dialog box Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 241 Select You get: OK in the dialog box Threaded Hole Creation In this section, we are going to create the following threaded hole Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 242 , then, select the following edge Activate the Hole icon Select the following face Enter the following parameters in the Hole dialog box, then, select OK Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 243 Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 244 You get: Assembling the Crank Set In this section, we are going to insert constraints between the toothing and the pedal support Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 245 In order to activate the Assembly Design workbench Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 246 Select the Coincidence Constraint icon By moving the mouse over the following hole, display its axis then, select it By moving the mouse over the following hole, display its axis then, select it Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 247 If necessary, select the Update All icon You get: Repeat these operations between the two following holes You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 248 Select the Contact Constraint icon Select the following face Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 249 Select the following face Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 250 10 If necessary, select the Update All icon You get: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 251 You can save the assembly Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br [...]... will design this small bracket to practice the various ways of using both the Sketcher and Part Design workbenches for designing parts One of the tools we will use in many different cases is the Sketching of a Profile and extruding Pads Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 28 Setting Part Design. .. cursor onto PartBody, then select properties from the contextual menu (MB3) Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 26 2 Select a color in the Fill combo, then select OK Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) ... 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 18 1 Select the Hole icon 2 Select the following face 3 Create a hole with the following parameters Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 19 You get: Creating Fillets In this section,... Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 20 1 We are going to create first the following fillet So select the Edge Fillet icon 2 Select the four following edges Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 21 3 Enter 3 in the Radius field of... 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 22 You get: 5 Using the same method, create an edge fillet with a radius of 2 at the following location Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 23 You get: 6 Using the same method, create... 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 24 You get: 7 Using the same method, create an edge fillet with a radius of 1 at the following location Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 25 You get: Changing the color In this section,... XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 14 You get: Creating Pockets In this section, we are going to create the following pockets 1 On the YZ plane create and constrain the following arc Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 15 2 Once you have left... Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 16 3 On the XY plane create and constrain the following profile 4 Once you have left the sketcher, create a pocket (With the previously created profile) with the following parameters Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 17... XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 29 1 We will first define all the sketches / pads for the Bracket We will start with the 3 mm thin flange 2 Select the XY plane and enter the Sketcher Draw the first sketch using Rectangle icon and dimension as follows: Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) ...TRV5PD (Exercicios) – Página 11 15 Now, we are going to Remove Body 1 from the main body Place the cursor on Body 1 then select Remove from the contextual menu Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios) – Página 12 Rua Cotoxó, 411 Sala 44 CEP 05121-000 ... TRV5PD (Exercicios) – Página Piston We will design this Piston to practice the various ways of using both the Sketcher and Part Design workbenches for designing parts Load the starting piston part. .. www.nvsistemas.com.br TRV5PD (Exercicios) – Página 27 You get: Angle Bracket We will design this small bracket to practice the various ways of using both the Sketcher and Part Design workbenches for designing parts... Sketcher and Part Design workbenches for designing parts Rua Cotoxó, 411 Sala 44 CEP 05121-000 São Paulo SP, Tel: XX-11-3675-2799 Fax: XX-11-3676-1363 www.nvsistemas.com.br TRV5PD (Exercicios)