MIR-1 DRIVER CONTROLS C D E F G H I J K M SECTION MIR A B MIR N O P CONTENTS MIRRORS PRECAUTION 2 PRECAUTIONS 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER" 2 Precaution for Procedure without Cowl Top Cover 2 Precautions for Removing Battery Terminal 3 PREPARATION 4 PREPARATION 4 Commercial Service Tools 4 SYSTEM DESCRIPTION 5 COMPONENT PARTS 5 Component Description 5 WIRING DIAGRAM 6 DOOR MIRROR SYSTEM 6 Wiring Diagram 6 DTC/CIRCUIT DIAGNOSIS 9 DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/CHANGEOVER SWITCH) 9 Component Inspection 9 SYMPTOM DIAGNOSIS 10 SQUEAK AND RATTLE TROUBLE DIAG- NOSES 10 Work Flow 10 Inspection Procedure 12 Diagnostic Worksheet 14 REMOVAL AND INSTALLATION 16 INSIDE MIRROR 16 Exploded View 16 Removal and Installation 16 OUTSIDE MIRROR 17 Exploded View 17 DOOR MIRROR ASSEMBLY 17 DOOR MIRROR ASSEMBLY : Removal and In- stallation 17 DOOR MIRROR ASSEMBLY : Disassembly and Assembly 18 GLASS MIRROR 19 GLASS MIRROR : Removal and Installation 19 DOOR MIRROR COVER 20 DOOR MIRROR COVER : Removal and Installa- tion 20 DOOR MIRROR REMOTE CONTROL SWITCH 21 Exploded View 21 Removal and Installation 21 Revision: 2014 October 2015 JUKE MIR-2 < PRECAUTION > PRECAUTIONS PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000011464346 The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual. WARNING: Always observe the following items for preventing accidental activation. • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”. • Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser- vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: Always observe the following items for preventing accidental activation. • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. • When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service. Precaution for Procedure without Cowl Top Cover INFOID:0000000011464347 When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield. PIIB3706J Revision: 2014 October 2015 JUKE PRECAUTIONS MIR-3 < PRECAUTION > C D E F G H I J K M A B MIR N O P Precautions for Removing Battery Terminal INFOID:0000000011464348 • When removing the 12V battery terminal, turn OFF the ignition switch and wait at least 30 seconds. NOTE: ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal is removed before ECU stops, then a DTC detection error or ECU data corruption may occur. • For vehicles with the 2-batteries, be sure to connect the main bat- tery and the sub battery before turning ON the ignition switch. NOTE: If the ignition switch is turned ON with any one of the terminals of main battery and sub battery disconnected, then DTC may be detected. • After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC. NOTE: The removal of 12V battery may cause a DTC detection error. SEF289H Revision: 2014 October 2015 JUKE MIR-4 < PREPARATION > PREPARATION PREPARATION PREPARATION Commercial Service Tools INFOID:0000000011464349 Tool name Description Remover tool Removes the clips, pawls and metal clips JMKIA3050ZZ Revision: 2014 October 2015 JUKE COMPONENT PARTS MIR-5 < SYSTEM DESCRIPTION > C D E F G H I J K M A B MIR N O P SYSTEM DESCRIPTION COMPONENT PARTS Component Description INFOID:0000000011464350 Item Function Door mirror remote control switch (mir- ror switch) It supplies power to mirror motor through mirror switch and changeover switch. Door mirror remote control switch (changeover switch) It transmits the LH/RH control of door mirror that supplies power. Door mirror motor It makes mirror face operate from side to side and up and down via integrated motor. Revision: 2014 October 2015 JUKE MIR-6 < WIRING DIAGRAM > DOOR MIRROR SYSTEM WIRING DIAGRAM DOOR MIRROR SYSTEM Wiring Diagram INFOID:0000000011464351 JRLWE3934GB Revision: 2014 October 2015 JUKE DOOR MIRROR SYSTEM MIR-7 < WIRING DIAGRAM > C D E F G H I J K M A B MIR N O P JRLWE3935GB Revision: 2014 October 2015 JUKE MIR-8 < WIRING DIAGRAM > DOOR MIRROR SYSTEM JRLWE3936GB Revision: 2014 October 2015 JUKE DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/ CHANGEOVER SWITCH) MIR-9 < DTC/CIRCUIT DIAGNOSIS > C D E F G H I J K M A B MIR N O P DTC/CIRCUIT DIAGNOSIS DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/ CHANGEOVER SWITCH) Component Inspection INFOID:0000000011464352 1.CHECK MIRROR SWITCH & CHANGEOVER SWITCH 1. Turn ignition switch OFF. 2. Disconnect door mirror remote control switch connector. 3. Check door mirror remote control switch. Is the inspection result normal? YES >> INSPECTION END. NO >> Replace door mirror remote control switch. Refer to MIR-21, " Removal and Installation". Door mirror remote control switch condition Continuity Terminal Change over switch Mirror switch Driver side 13 6 LEFT RIGHT Existed 12 5 13 5 LEFT 12 6 13 2 UP 12 6 13 6 DOWN 12 2 Passenger side 13 7 RIGHT RIGHT 12 4 13 4 LEFT 12 7 13 3 UP 12 7 13 7 DOWN 12 3 Revision: 2014 October 2015 JUKE MIR-10 < SYMPTOM DIAGNOSIS > SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS SQUEAK AND RATTLE TROUBLE DIAGNOSES Work Flow INFOID:0000000011464353 CUSTOMER INTERVIEW Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag- nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any customer comments. Refer to MIR-14, " Diagnostic Worksheet". This information is necessary to duplicate the conditions that exist when the noise occurs. • The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain all the facts and conditions that exist when the noise occurs (or does not occur). • If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that the customer is concerned about. This can be accomplished by performing a test drive with the customer. • After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics are provided so that the customer, service adviser, and technician use the same language when describing the noise. • Squeak – (Like tennis shoes on a clean floor) Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard sur- faces = high-pitched noise / softer surfaces = low-pitched noises / edge to surface = chirping • Creak – (Like walking on an old wooden floor) Creak characteristics include firm contact / slow movement/twisting with a rotational movement / pitch dependent on materials / often brought on by activity. • Rattle – (Like shaking a baby rattle) Rattle characteristics include fast repeated contact / vibration or similar movement / loose parts/missing clip or fastener / incorrect clearance. • Knock – (Like a knock on a door) Knock characteristics include hollow sounds / sometimes repeating / often brought on by driver action. • Tick – (Like a clock second hand) Tick characteristics include gentle contacting of light materials / loose components / can be caused by driver action or road conditions. • Thump – (Heavy, muffled knock noise) Thump characteristics include softer knock / dull sounds often brought on by activity. • Buzz – (Like a bumblebee) Buzz characteristics include high frequency rattle / firm contact. • Often the degree of acceptable noise level varies depending upon the person. A noise that a technician may judge as acceptable may be very irritating to a customer. • Weather conditions, especially humidity and temperature, may have a great effect on noise level. DUPLICATE THE NOISE AND TEST DRIVE SBT842 Revision: 2014 October 2015 JUKE [...]... blocks, felt cloth tape, or urethane tape A NISSAN Squeak and Rattle Kit (J-50397) is available through the authorized NISSAN Parts Department M CAUTION: Never use excessive force as many components are constructed of plastic and may be damaged NOTE: Always check with the Parts Department for the latest parts information N The following materials are contained in the NISSAN Squeak and Rattle Kit (J-50397)... causing the noise N O P Revision: 2014 October MIR-13 2015 JUKE SQUEAK AND RATTLE TROUBLE DIAGNOSES < SYMPTOM DIAGNOSIS > Diagnostic Worksheet INFOID:0000000011464355 PIIB8740E Revision: 2014 October MIR-14 2015 JUKE SQUEAK AND RATTLE TROUBLE DIAGNOSES < SYMPTOM DIAGNOSIS > A B C D E F G H I J K MIR M N O PIIB8742E P Revision: 2014 October MIR-15 2015 JUKE INSIDE MIRROR < REMOVAL AND INSTALLATION > REMOVAL... areas can usually be insulated with felt cloth tape or insulator foam blocks from the NISSAN Squeak and Rattle Kit (J-50397) to repair the noise TRUNK Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer In addition check for the following items: Revision: 2014 October MIR-12 2015 JUKE SQUEAK AND RATTLE TROUBLE DIAGNOSES < SYMPTOM DIAGNOSIS > 1 Trunk lid dumpers... thick, 50 × 50 mm (1.969 × 1.969 in) INSULATOR (Light foam block) 80845-71L00: 30 mm (1.181 in) thick, 30 × 50 mm (1.181 × 1.969in) FELT CLOTHTAPE REPAIR THE CAUSE • • - Revision: 2014 October MIR-11 2015 JUKE SQUEAK AND RATTLE TROUBLE DIAGNOSES < SYMPTOM DIAGNOSIS > Used to insulate where movement does not occur Ideal for instrument panel applications • 68370-4B000: 15 × 25 mm (0.591 × 0.984 in) pad •... use excessive force to remove the inside mirror because it is inserted tightly into the mirror base JMLIA0055ZZ INSTALLATION Install in the reverse order of removal Revision: 2014 October MIR-16 2015 JUKE OUTSIDE MIRROR < REMOVAL AND INSTALLATION > OUTSIDE MIRROR A Exploded View INFOID:0000000011464358 B C D E F G H I J JMLIA6142GB Side turn signal lamp 3 Door mirror finisher (without around view monitor... ASSEMBLY DOOR MIRROR ASSEMBLY : Removal and Installation INFOID:0000000011464359 CAUTION: When removing, always use a remover tool that is made of plastic P REMOVAL Revision: 2014 October MIR-17 O 2015 JUKE OUTSIDE MIRROR < REMOVAL AND INSTALLATION > 1 Disengage door mirror corner cover fixing clips using a remover tool (A), and then remove door mirror corner cover : Clip JMLIA1391ZZ 2 3 4 Remove front... and Installation" • Halogen type: Refer to EXL-212, "Removal and Installation" ASSEMBLY Note the following item, and then assemble in the reverse order of disassembly Revision: 2014 October MIR-18 2015 JUKE OUTSIDE MIRROR < REMOVAL AND INSTALLATION > CAUTION: Perform side camera image calibration (with side camera) Refer to AV-114, "CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description" GLASS... mirror INSTALLATION Note the following item, and then install in the reverse order of removal CAUTION: After installation, visually check that pawls are securely engaged Revision: 2014 October MIR-19 2015 JUKE P OUTSIDE MIRROR < REMOVAL AND INSTALLATION > DOOR MIRROR COVER DOOR MIRROR COVER : Removal and Installation INFOID:0000000011464361 REMOVAL 1 2 Remove the glass mirror Refer to MIR-19, "GLASS MIRROR... JMLIA5688ZZ INSTALLATION Note the following item and then install in the reverse order of removal CAUTION: After installation, visually check that pawls are securely engaged Revision: 2014 October MIR-20 2015 JUKE DOOR MIRROR REMOTE CONTROL SWITCH < REMOVAL AND INSTALLATION > DOOR MIRROR REMOTE CONTROL SWITCH A Exploded View INFOID:0000000011464362 B C D E F JMLIA1446ZZ 1 Instrument lower panel 2 Switch bracket... mirror remote control switch (1) from switch bracket (2) using remover tool (A) I : Pawl J K JMLIA1447ZZ MIR INSTALLATION Install in the reverse order of removal M N O P Revision: 2014 October MIR-21 2015 JUKE