ENGLISH FOR AUTOMOBILE ENGINEERING-UNIT 4: MANUAL OPERATION pot

12 699 8
ENGLISH FOR AUTOMOBILE ENGINEERING-UNIT 4: MANUAL OPERATION pot

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

ENGLISH FOR AUTOMOBILE ENGINEERING UNIT MANUAL OPERATION Lecturer: Lang Van Thang Presentation Select the correct instructions for the actions in Figure 4.1: For example: A = Turn the jack handle anticlockwise to lower the car Turn the gear wheel anticlockwise to raise the drill Turn the bolt clockwise to tighten it Press the top button to stop the motor Press the largest pedal to stop the car Pull the handle down to cut the metal bar Push the bar down to raise the load Practice Use the diagrams below and words in the presentation to complete the instructions: Practice Read the instructions for checking a spark plug; then put them in the correct order Remove the plug from the socket Place the spanner over the spark plug Replace the spark plug in the socket Insert the gauge in the gap Remove the cover Examine the gap and check that it is clean Rotate the plug anticlockwise until it is loose Check that the gap is between 0.65 and 1.00 mm wide Replace the cover 10.Rotate the plug clockwise until it is hand-tight 11.Place the spanner over the plug and give a quarter turn clockwise 12.Caution: not over-tighten the plug Practice Read the instructions for changing a tyre; then put them in the correct order Practice Read the instructions for the dynamo belt on the left; then complete the instructions for the alternator belt on the right: Slacken mounting bolts A and B Slacken the slide bolt C Either: a pull the dynamo up to tighten the belt or : b push the dynamo down to slacken the belt Tighten the slide bolt Tighten the mounting bolts Fan belt adjustment on models with a dynamo Practice _ _ _ _ Either: a _ _ or: b _ _ _ Fan belt adjustment _ on models with an _ alternator _ Practice a Cover the car components Can you remember which nouns can follow which verbs: complete the table: Open/close Adjust Switch on/off check Practice b Now work with a partner to answer the following questions Using phrases from the table above What you when visibility is poor because of fog? your seat is too low? you think you need oil? you want to gat out of the car? you can’t see the cars behind you properly? it’s getting dark: you want to look at the engine? your steering wheel is too high? you think your tyre pressure is low? 10.you need your road map? 11.it’s warm and sunny? 12.your passenger has no legroom in the back? Development Read the text, label Figure 4.2 and solve the problem In a petrol engine, the movement of the pistons between the bottom and top of the cylinder is termed the piston stroke The highest position of the piston is called the Top Dead Centre (TDC) position (see Figure 4.2) When the piston is in this position, the volume between the cylinder head and the top of the piston is known as the clearance volume The lowest position of the piston is called the Bottom Dead Centre (BDC) position The difference between the clearance volume and the total volume when the piston is in the BDC position is called the working volume In other words, to find the working volume, multiply the length of the piston stroke by the cross-sectional area of the cylinder To find the compression ratio of an engine, divide the total volume when the piston is in the BDC position (i.e the working volume + clearance volume) by the clearance volume Therefore, for the engine in figure 4.2: ( _ + ) / _ = The engine therefore has a _ : _ compression ratio ... Read the instructions for changing a tyre; then put them in the correct order Practice Read the instructions for the dynamo belt on the left; then complete the instructions for the alternator belt... working volume + clearance volume) by the clearance volume Therefore, for the engine in figure 4.2: ( _ + ) / _ = The engine therefore has a _ : _ compression ratio ...Presentation Select the correct instructions for the actions in Figure 4.1: For example: A = Turn the jack handle anticlockwise to lower the car Turn the gear

Ngày đăng: 22/03/2014, 23:20

Từ khóa liên quan

Mục lục

  • UNIT 4

  • Presentation

  • Practice 1

  • Slide 4

  • Practice 2

  • Practice 3

  • Practice 4

  • Slide 8

  • Practice 5

  • Slide 10

  • Development

  • Slide 12

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan