low temperature hydrothermal synthesis of monodispersed flower - like titanate nanosheets

5 443 0
low temperature hydrothermal synthesis of monodispersed flower - like titanate nanosheets

Đang tải... (xem toàn văn)

Thông tin tài liệu

Low temperature hydrothermal synthesis of monodispersed flower-like titanate nanosheets Jaturong Jitputti a , Thitima Rattanavoravipa a , Surawut Chuangchote a , Sorapong Pavasupree b , Yoshikazu Suzuki a , Susumu Yoshikawa a, * a Institute of Advanced Energy, Kyoto University, Uji, Kyoto, 611-0011, Japan b Department of Materials and Metallurgical Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Klong 6, Pathumthani, 12110, Thailand article info Article history: Received 23 April 2008 Received in revised form 25 September 2008 Accepted 26 September 2008 Available online 2 October 2008 Keywords: Titania Flower-like Sphere Nanosheets Template-free Hydrothermal abstract Monodispersed flower-like titanate superstructure was successfully prepared by simple hydrothermal process without any surfactant or template. N 2 -sorption analysis, scanning electron microscopy (SEM), and X-ray diffraction (XRD) observation of as-synthesized product revealed the formation of flower-like titanate with diameter of about 250–450 nm and BET surface area (S BET ) of 350.7 m 2 g À1 . Upon thermal treatment at 500 °C, the titanate nanosheets were converted into anatase TiO 2 with moderate deforma- tion of their structures. The as-prepared flower-like titanate showed high photocatalytic activity for H 2 evolution from water splitting reaction. Moreover, the sample heat treated at 500 °C exhibited higher photocatalytic activity than that of commercial TiO 2 anatase powder (ST-01). Ó 2008 Elsevier B.V. All rights reserved. 1. Introduction Titania (TiO 2 ) is an attractive semiconducting material due to its characteristic photochemical properties and high chemical stabil- ity [1]. Applications of TiO 2 have been explored in different fields including optoelectronics [2], photocatalysts [3], photoelectrodes [4], lithium rechargeable batteries [5], and sensor devices [6]. Many studies in the fundamental and practical fields have been performed using nanoscale materials, because a high specific sur- face is generally required for their applications [1]. In addition, many different methods and techniques have been developed for the preparation of TiO 2 nanomaterials, including sol–gel technique [7], micelle and inverse micelle methods [8], solvothermal method [9], chemical vapor deposition [10], electrodeposition [10], hydro- thermal method [11], etc. In contrast to other techniques, the hydrothermal method offers an inexpensive and environmentally friendly route and the ability to control chemical, homogeneity, purity, morphology, shape, and phase composition of the powder under moderate conditions [12–14]. Since it is known that the structural, thermal, electronic, and optical properties of TiO 2 nanomaterials are strongly depended on their size, shape, and crystal structure, several attempts have been paid on the preparation of special morphologies of TiO 2 nano- structure, such as nanotube [15], nanowire [16], hollow nano- sphere [17], nanosphere [18], nanosheets [1,19], due to the fact that the synthesis of these TiO 2 nanomaterials offer fundamental scientific opportunities for investigating the influence of size and dimensionality of materials with respect to their properties. In our previous work, we have reported the synthesis of spherical TiO 2 nanosheets (flower-like morphology composed of nano- sheets) via simple hydrothermal synthesis using titanium butoxide as starting material [19]. Our results showed that this prepared spherical TiO 2 nanosheets exhibit higher photocatalytic activity and efficiency for dye-sensitized solar-cell when compared to the commercial TiO 2 nanoparticles (Ishihara ST-01 and Degussa P25). However, the TiO 2 prepared by this method were not homoge- neous in size with large diameter raging from 500 nm to 2 l m. So it is meaningful to develop a simple method to synthesize the spherical TiO 2 nanosheets with homogeneous size at rather low temperature. In this work, we report a simple hydrothermal approach for preparation of spherical titanate nanosheets by a novel 2-step method combining the synthesis of spherical amorphous titania using controlled hydrolysis and formation of spherical titanate nanosheets by hydrothermal treatment in ammonia aqueous solution. The effects of hydrothermal treatment temperature and time are also investigated. The spherical titanate nanosheets can 1566-7367/$ - see front matter Ó 2008 Elsevier B.V. All rights reserved. doi:10.1016/j.catcom.2008.09.026 * Corresponding author. Tel.: +81 774 38 3502; fax: +81 774 38 3508. E-mail address: s-yoshi@iae.kyoto-u.ac.jp (S. Yoshikawa). Catalysis Communications 10 (2009) 378–382 Contents lists available at ScienceDirect Catalysis Communications journal homepage: www.elsevier.com/locate/catcom be easily converted into spherical TiO 2 nanosheets by thermal treatment at 500 °C. 2. Experimental 2.1. Preparation of monodispresed amorphous TiO 2 spheres Monodispersed amorphous spherical TiO 2 particles were syn- thesized through controlled hydrolysis of titanium tetraisopropox- ide (TTIP, Ti-(OC 3 H 7 ) 4 , 97%, Aldrich) in ethanol [13]. Typically, 100 mL of ethanol was mixed with 0.4 mL of 0.1 M aqueous potas- sium chloride, followed by the addition of 2.2 mL of TTIP at ambi- ent temperature under stirring condition. The solution was mixed until a white precipitate appeared. The suspension was aged in a static condition for 24 h in a closed container at room temperature (25 °C). The powder (denoted as AS) suspended in the vessel was collected by filtration and dried at 60 °C in air. 2.2. Preparation of titanate nanosheets Monodispersed spherical titanate nanosheets were prepared by hydrothermal treatment in ammonia solution. An amount of 0.3 g of AS was suspended in 60 ml of ammonia solution (20 ml of 28% ammonia solution, 40 ml of distilled water, pH 12) in 80-ml Tef- lon-line stainless autoclave at 60, 80, 100, and 120 °C with stirring condition for 12 and 24 h. The obtained powder was then washed by distilled water and ethanol. 2.3. Characterization X-ray diffraction (XRD) analyses were performed on a powder diffractometer (Rigaku RINT-2100). The microstructure of the pre- pared materials was analyzed by scanning electron microscopy (SEM, JEOL JSM-6500FE) The nitrogen sorption isotherm and Bru- nauer–Emmett–Teller (BET) specific surface area were determined by nitrogen adsorption method (BEL Japan, BELSORP-18 Plus). 2.4. Photocatalytic measurement The photocatalytic activity measurement was evaluated with H 2 evolution from water splitting reaction. The procedure was basically the same as described in previous work [20,21]. The reaction was carried out in a closed gas-circulation system. The amount of 1 g of sample was suspended in aqueous methanol solution (800 mL distilled H 2 O, 80 mL methanol) by means of magnetic stirrer in an inner irradiation-type photoreactor made of Pyrex glass. The mixture was purged by Argon gas (Ar) to re- move the air dissolved in solution. The suspension was irradiated by a 450 W high-pressure Hg lamp (Ushio UM-452) and cooling water was circulated through a cylindrical Pyrex jacket located around the UV light source to maintain the reaction temperature. The evolved gasses were periodically analyzed by an on-line gas chromatograph (Shimadzu GC-8A, Molecular sieve 5A, TCD, Ar Carrier). 3. Results and discussion Generally, transition metal alkoxides are very reactive with moisture, heat, and light due to the presence of highly reactive alk- oxy (OR) groups. In sol-gel processing of metal alkoxides, hydroly- sis and condensation reactions occur so rapidly that uniform and fine particles are difficult to obtain. However, the use of bulky, branched alkoxy groups (such as TTIP) could reduce the hydrolysis rates as reaction rates decrease with the steric bulk of alkoxy li- gands to favor the formation of fine particles with a more uniform size distribution. Another approach to retard the hydrolysis and condensation rates is the chemical modification of metal alkoxides with modified agent, such as alcohols and acids or bases [22].In this work, spherical TiO 2 nanoparticles were formed through a con- trolled hydrolysis of TTIP in ethanol [23]. Fig. 1 shows the XRD patterns of AS and the samples hydrother- mally prepared in ammonia solution for 24 h at 60 to 120 °C. No XRD pattern of AS was found, indicating the amorphous nature of the samples obtained by hydrolysis of TTIP. 5 10152025303540455055 6 0 CuK α θ , 2 / Degree Intensity / a.u. (b) (e) (d) (c) (a) (f) 010 211105 200 004 Fig. 1. XRD patterns of (a) sample obtained by hydrolysis of TTIP with 0.1 M KCl solution (AS), and samples hydrothermally treated in ammonia for 24 h at (b) 60 °C, (c) 80 °C, (d) 100 °C, (e) 120 °C and (f) sample hydrothermally treated in ammonia at 120 °C, 12 h followed by thermal treatment at 500 °C for 1 h. Fig. 2. (a) SEM image and (b) high magnification SEM image of samples obtained by hydrolysis of TTIP. J. Jitputti et al. /Catalysis Communications 10 (2009) 378–382 379 According to XRD measurement, the XRD data of hydrother- mally treated samples prepared at P80 °C show a poorly crystal- line titanate. The peak at around 2h % 9° indicated that titanate has a layer structure with an interlayer distance of ca.1.0 nm. The broad peaks in the high-angle region were similar to the theoretically estimated diffraction peaks for layered titanate (NH 4 ) 2 Ti 3 O 7Àx N x [1,24]. However, the peak cannot be clearly ob- served for the sample prepared at 60 °C. Recently, Takezawa and Imai have reported the formation of layered titanate in the basic solutions [1,25]. According to their work, the layered titanates can be constructed by stacking of anio- nic TiO 2 manolayers with the counter cations (NH 4 + or Na + ). How- ever, almost the same amount of anionic species and cationic agents, and a basic condition above pH 8 are required for the for- mation of the titanates [25]. As mentioned above, the pH of ammo- nia solution used in our experiments was pH 12. Therefore, the pH of ammonia solution used was sufficient for the formation of the layered titanates. The morphologies of resulting samples were investigated by scanning electron microscopy (SEM). Fig. 2 gives the morphologies of AS. As shown in Fig. 2a, uniform, solid spherical particles were obtained after 24-h. The high magnification SEM image (Fig. 2b) shows that the surface of these spheres is relatively smooth with size of 250 to 450 nm. Fig. 3 shows the high magnification SEM images of hydrother- mally prepared samples prepared for 12 and 24 h at 60 to 120 °C. Fig. 3. SEM images of samples hydrothermally prepared at (a) 60 °C, 12 h, (b) 60 °C, 24 h, (c) 80 °C, 12 h, (d) 80 °C, 24 h, (e) 100 °C, 12 h, (f) 100 °C, 24 h, (g) 120 °C,12 h, and (h) 120 °C, 24 h. 380 J. Jitputti et al. /Catalysis Communications 10 (2009) 378–382 After hydrothermal treatment in ammonia solution, the size of these spheres was not changed too much. However, their surfaces became rough. Obviously, nanosheets structure could be observed for all samples prepared at temperature P80 °C(Fig. 3c–h). Our results showed that, for this preparation method, the hydrothermal temperature was a critical factor. As seen in Fig. 3c–h, nanosheet structure could be obtained for samples prepared at P80 °C. At 60 °C, the nanosheet morphology could not be ob- tained in the sample prepared for 12 h (Fig. 3a). However, the nanosheet structure could be observed for sample prepared for 24 h (Fig. 3b). Therefore, it can be preferably concluded that the longer time or higher temperature was required in order to obtain nanosheet structure. Some physical properties of AS and flower-like titanate super- structure prepared at 120 °C for 12 h are listed in Table 1. The spe- cific surface area of the products obtained at 120 °C, 12 was estimated to be about 350.7 m 2 g À1 . Such a high value of the specific surface area suggests that the nanosheet structure provide high sur- face area. In addition, it has been reported that the interlayer spac- ing can provide an effective surface for the adsorption of nitrogen molecules [1]. The sample prepared at 120 °C, 12 h was then heat treated at 500 °C to investigate the effect of treatment temperature. Upon thermal treatment at 500 °C for 1 h, the titanate nano- sheets were converted into anatase TiO 2 (Fig. 1f), with slightly deformation of their structures (Fig. 4). The anatase nanosheets exhibited specific surface area about 31.7 m 2 g À1 , where the thick- ness of the sheets was estimated to be larger than 15 nm from SEM images. Fig. 5 shows the UV–Vis spectra of AS, flower-like titanate and flower-like titanate calcined at 500 °C which are compared with that of commercial Ishihara ST-01 (ST-01). The AS shows an absorption edge at around 380 nm. This absorption value is signif- icantly lower than that of ST-01 (390 nm). The flower-like titanate sample exhibits a main absorption edge at 385 nm and, in addition, a shoulder that extends above 430 nm. Upon calcination of flower- like titanate at 500 °C, the obtained TiO 2 anatase (Fig. 1) shows an absorption edge at around 400 nm. Preliminary measurement of photocatalytic activity was evalu- ated with H 2 evolution from water splitting reaction under UV light irradiation. For comparison, the same measurement was also car- ried out on ST-01 sample as the reference. The results are shown in Fig. 6. As shown in Fig. 6, the amount of H 2 evolved after 5 h irradia- tion for ST-01was estimated to be 92 l mol g À1 . In case of AS, the Table 1 The physical properties of AS, flower-like TiO 2 superstructure prepared at 120 °C for 12 h, and flower-like TiO 2 superstructure calcined at 500 °C. Materials Crystal structure S BET /m 2 g À1 Amount of H 2 evolved l mol g À1 l mol m 2 AS Amorphous 128.2 72 0.56 FL TiO 2 Titanate 350.7 342 0.97 FL TiO 2 (500 °C) Anatase 31.7 588 18.6 Fig. 4. SEM images of (a) sample hydrothermally prepared at 120 °C,12 h, and (b) followed by calcination at 500 °C for 1 h. 300 350 400 450 500 550 600 Wavelenght / nm Adsorbsion (arb unit) (b) (c) (d) (a) Fig. 5. UV–Vis diffuse reflectance of (a) ST-01 (anatase powder), (b) AS, (c) as- prepared flower-like titanate, and (d) flower-like titanate calcined at 500 °C. 0 100 200 300 400 500 600 700 0 50 100 150 200 250 300 Irradiation time / min H 2 evolved / μ mol g -1 (a) ST01 (b) AS (d) Flower-like TiO 2 (calcined 500 o C) (c) Flower-like titanate Fig. 6. Photocatalytic H 2 evolution from water splitting reaction over (a) ST-01 (anatase powder), (b) AS, (c) as-prepared flower-like titanate, and (d) flower-like titanate calcined at 500 °C. J. Jitputti et al. /Catalysis Communications 10 (2009) 378–382 381 amount of H 2 evolved was estimated to be 72 l mol g À1 , which was lower than that of ST-01. This was expected because the AS possess amorphous phase which generally show lower photocatalytic activity when compared to crystalline TiO 2 photocatalyst. The amount of H 2 evolved was raised to be 342 l mol g À1 when as-syn- thesized flower-like titanate was used. However, the imperfect crystallization from XRD spectra (Fig. 1) accompanying with amor- phous phase, which favorably increase the probability of mutual e À /h + recombination at both surface and bulk trap, contained to some extent in the as-synthesized flower-like titanate resulted in the decrease in H 2 evolution rate after 2 h of reaction (Fig. 6). The amount of H 2 evolved was raised to be 588 l mol g À1 when the flower-like TiO 2 calcined at 500 °C was used. This was due to the spherical TiO 2 nanosheets calcined at 500 °C has anatase struc- ture which show highest activity when compared to other TiO 2 phase [20,21,26]. Moreover, the UV–Vis spectra (Fig. 5) shows that the number of absorbed photon of flower-like TiO 2 calcined at 500 °C is larger than other samples. The results revealed that the use of the flower-like TiO 2 with unique structure could promote great H 2 evolution. In summary, this study provides a simple route for fabrication of flower-like titanate superstructure with uniform size under mild condition. In addition, we found that the hydrothermal treatment in ammonia solution used in this study can also be applied to pre- pare other nanosheets-composed TiO 2 materials, such as TiO 2 nanowires and TiO 2 nanowire arrays. The results will be reported and discussed in the forthcoming work. Furthermore, it is expected that the hydrothermal treatment in ammonia solution could also be applied to other nanostructured materials. 4. Conclusion Monodispersed amorphous TiO 2 spheres were prepared by con- trolled hydrolysis of titanium isopropoxide in ethanol. By applying the hydrothermal treatment in ammonia solution, flower-like tita- nate of desired morphology could be easily prepared from amor- phous TiO 2 spheres. In addition, it was obvious that temperature exerts a great influence on the structure of the products prepared by this method. Moreover, the titanate nanosheets could be easily converted into anatase TiO 2 by calcination at 500 °C. Preliminary photocatalytic activity measurement showed that the flower-like titanate superstructure show high photocatalytic activity due to their unique structure. Moreover, the sample heat treated at 500 °C, which show anatase phase, exhibit higher photocatalytic activity than that of commercial TiO 2 anatase powder (ST-01). Acknowledgements The authors would like to express their gratitude to Prof. T. Yoko, Assoc. Prof. M. Takahashi, and Asst. Prof. Y. Tokuda, Institute for Chemical Research, Kyoto University for the use of XRD equipment. References [1] Y. Takezawa, H. Imai, Small 2 (2006) 390. [2] Y. Wang, L. Li, K. Yang, L.A. Samuelson, J. Kumar, J. Am. Chem. Soc. (Communication) 129 (2007) 7238. [3] A. Fujishima, K. Honda, Nature 238 (1972) 37. [4] B. O’Regan, M. Gratzel, Nature 353 (1991) 737. [5] L. Kavan, A. Attia, F. Lenzmann, S.H. Elder, M. Gratzel, J. Electrochem. Soc. 147 (2000) 2897. [6] X. Du, Y. Wang, Y. Mu, L. Gui, P. Wang, Y. Tang, Chem. Mater. 14 (2002) 3953. [7] Y. Bessekhouad, D. Robert, J.V. Weber, J. Photochem. Photobiol. A 157 (2003) 47. [8] S.S. Hong, M.S. Lee, S.S. Park, G.D. Lee, Catal. Today 87 (2003) 99. [9] B. Wen, C. Liu, Y. Liu, J. Phys. Chem. B 109 (2005) 12372. [10] J.A. Ayllon, A. Figueras, S. Garelik, L. Spirkova, J. Durand, L. Cot, J. Mater. Sci. Lett. 18 (1999) 1319. [11] J. Yang, S. Mei, J.M.F. Ferreira, J. Am. Ceram. Soc. 83 (2000) 1361. [12] Z. Wu, N. Kumagai, M. Yoshimura, Chem. Mater. 12 (2000) 3356. [13] Y. Wang, H. Xu, X. Wang, X. Zhang, H. Jia, L. Zhang, J. Qiu, J. Phys. Chem. B 110 (2006) 13835. [14] J. Jitputti, P. Charoensirithavorn, S. Yoshikawa, Chem. Lett. 36 (2007) 1508. [15] Y. Ding, Z.L. Wang, J. Phys. Chem. B 108 (2004) 12280. [16] H. Li, Z. Bian, J. Zhu, D. Zhang, G. Li, Y. Huo, H. Li, Y. Lu, J. Am. Chem. Soc. (Communication) 129 (2007) 8406. [17] J.L. Look, C.F. Zukoski, J. Am. Ceram. Soc. 75 (1992) 1587. [18] X. Chen, S.S. Mao, Chem. Rev. 107 (2007) 2891. [19] S. Pavasupree, S. Ngamsinlapasathian, Y. Suzuki, S. Yoshikawa, Mater. Lett. 61 (2007) 2973. [20] J. Jitputti, S. Pavasupree, Y. Suzuki, S. Yoshikawa, J. Solid State Chem. 180 (2007) 1743. [21] J. Jitputti, S. Pavasupree, Y. Suzuki, S. Yoshikawa, Catal. Commun. 9 (2008) 1265. [22] M. Pal, J.G. Serrano, P. Santiago, U. Pal, J. Phys. Chem. C 111 (2007) 96. [23] S. Qourzal, A. Assabbane, Y. Ait-Ichou, J. Photochem. Photobiol. A: Chem. 163 (2004) 317. [24] C.H. Rhee, S.W. Bae, J.S. Lee, Chem. Lett. 34 (2005) 660. [25] Y. Takezawa, H. Imai, J. Cryst. Growth 308 (2007) 117. [26] T. Sreethawong, Y. Suzuki, S. Yoshikawa, J. Solid State Chem. 178 (2005) 329. 382 J. Jitputti et al. / Catalysis Communications 10 (2009) 378–382 . Low temperature hydrothermal synthesis of monodispersed flower-like titanate nanosheets Jaturong Jitputti a , Thitima. titanate nanosheets Monodispersed spherical titanate nanosheets were prepared by hydrothermal treatment in ammonia solution. An amount of 0.3 g of AS was

Ngày đăng: 20/03/2014, 13:04

Từ khóa liên quan

Mục lục

  • Low temperature hydrothermal synthesis of monodispersed flower-like titanate nanosheets

    • Introduction

    • Experimental

      • Preparation of Monodispresed Amorphous monodispresed amorphous TiO2 spheres

      • Preparation of titanate nanosheets

      • Characterization

      • Photocatalytic measurement

      • Results and discussion

      • Conclusion

      • Acknowledgements

      • References

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan