Show ip bgp neighbors Command Field Descriptions

... Data Bytes Total number of data bytes show ip bgp neighbors Command Field Descriptions Field Description BGP Neighbor IP address of the BGP neighbor and its AS number; if the neighbor ... peer is an EBGP peer BGP Version BGP version being used to communicate with the remote router Remote Router ID Highest non-loopback IP address on the router or highest lo...

Ngày tải lên : 27/10/2013, 07:15

3
394
0

Tài liệu Show frame-relay pvc Command Field Descriptions doc

... Show frame-relay pvc Command Field Descriptions Field Description DLCI One of the DLCI numbers for the PVC DLCI USAGE Lists ... voice traffic Voice Reserved Queues Queue numbers reserved for voice traffic on this PVC; this field was removed in Cisco IOS Release 12.0(5)T Fragment Type Type of fragmentation configured

Ngày tải lên : 11/12/2013, 14:15

2
274
0

Tài liệu show ipx interface e0 Command Field Descriptions pptx

... show ipx interface e0 Command Field Descriptions Field Description Ethernet0 is up, line protocol is up Type of interface ... (configured with the ipx link-delay interface configuration command) IPXWAN processing Indicates whether IPXWAN processing has been enabled on this interface with the ipx ipxwan command IPX SAP update ... Value of the Ticks field (configured...

Ngày tải lên : 21/12/2013, 19:15

2
254
0

Tài liệu show ipx traffic Command Field Descriptions pptx

... improperly configured. show ipx traffic Command Field Descriptions Field Description Time since last clear Elapsed time since last clear command issued. Rcvd: Description of the packets ... received. RIP: Description of the Routing Information Protocol (RIP) packets received and sent. RIP requests Number of RIP requests received. ignored Number of RIP requests...

Ngày tải lên : 21/12/2013, 19:15

3
239
0

Tài liệu show interfaces bri Field Descriptions doc

... problems if the carrier-detect line is changing state often show interfaces bri Field Descriptions Field Description BRI Is {up | down | administratively down} Indicates whether ... the interface as a multiple of 1/255 (255/255 is 100-percent reliability), calculated as an exponential average over 5 minutes Load Load on the interface as a multiple of 1/255 (255/255 ....

Ngày tải lên : 11/12/2013, 14:15

3
235
0

Tài liệu Debug isdn q931 Command Call Setup Procedure Field Descriptions doc

... debug isdn q931 Command Call Setup Procedure Field Descriptions Field Description TX -> Indicates that this message is being transmitted ... Number Identifies the called party; this field is present only in outgoing SETUP messages; note that it can be replaced by the Keypad Facility field; this field uses the IA5 character set Calling ... identifier; the value depe...

Ngày tải lên : 11/12/2013, 14:15

2
208
0

Lab 9.3.5 Troubleshooting Routing Issues with show ip route and show ip protocols

... Lab 9.3.5 Troubleshooting Routing Issues with show ip route and show ip protocols Objective • Use the show ip route and show ip protocol commands to diagnose a routing configuration problem. ... LAN. So use the show ip protocol command to view the routing protocol status. From the Birmingham router, type the following: BHM #show ip protocol b. What net...

Ngày tải lên : 23/10/2013, 00:15

6
333
1

Lab 9.3.5 Troubleshooting Routing Issues with show ip route and show ip Protocols

... Ethernet LAN. So use the show ip protocol command to view the routing protocol status. From the Gadsden router, type the following: GAD #show ip protocol b. What networks is RIP routing? _____________________ ... an unsuccessful ping, check the routing table with the show ip route command. From the Gadsden router, type the following: GAD #show ip route 2 - 6 C...

Ngày tải lên : 27/10/2013, 07:15

6
419
0

Tài liệu Debug isdn q921 Field Descriptions pdf

... local router during the TEI check procedure; this message is sent in a UI command frame; the ri field is always 0; the ai field for this message contains either a specific TEI value for the local ... procedure; this message is sent in a UI command frame in response to the IDCKRQ message; the ri field is a randomly generated number between 0 and 65535; the ai field for this mes...

Ngày tải lên : 11/12/2013, 14:15

3
191
0

Tài liệu Lab 9.1.1 Using Show IP Route to Examine Routing Tables doc

... _________________________________________________ d. Stop the debug with no debug ip rip. Step 5 Show the routing tables for each router a. Examine the routing table entries, using command show ip route command on each router. b. What are ... Type the command clear ip route * at the privileged EXEC prompt on both routers. Wait at least 90 seconds. Then type the command...

Ngày tải lên : 18/01/2014, 05:20

6
424
0