... the backup drive normally will be given a
list of instructions like the following:
1. Position to block 1000
2. Read one block of data
3. Position to block 10 03
4. Read one block of data
5. Position ... At one time, Transarc was working on an API to which some of
the vendors were going to port. As of this writing, however, only one company seems to have
backup support for DFS. If DFS i...
... server
VOBS='cleartool lsvob -host $HOST¦sed 's/*//' ¦awk '{print $1}''
case $1 in
lock )
for VOB in $VOBS ; do
# (Lock VOBS)
cleartool lock -c 'VOB backups in progress' ... it for each transaction dump.
load transaction baddbname from '/dev/nrmt0'
For more information on how to load dumps and transaction logs, please refer to
'&apos...
... 95472.
Editor: Gigi Estabrook
Production Editor: Clairemarie Fisher O& apos;Leary
Printing History:
November 1999: First Edition.
Nutshell Handbook, the Nutshell Handbook logo, and the O& apos ;Reilly logo ... publisher assumes no
responsibility for errors or omissions, or for damages resulting from the use of the information
their alignment if stored in that position for too long. (CD-R...
... command is not a backup command used by most people. It is a very low-level
command and is designed for copying bits of information from one place to another. It does not
have any knowledge of ... version of
cpio, as is the ability to use remote devices.
Option: specifying the output mode (o)
The o option is one of the three modes of cpio (o, i, and p) and is the one used for creat...
... the
basic "boot" information. The main part of this block is the location on the disk where the
kernel is stored. This block of boot information, or boot block, is stored outside, or "in ... for your particular version.) This command performs a chroot to /root, then
reads /etc/lilo.conf to determine what to put in the master boot block. It then rebuilds the boot
block for you....
... Seriously, though, the reason it is so difficult is that you need a
good SA and a good DBA to design a good backup plan. Most people know only one side
well. If you or your people know both sides, ... backups
Configuration Options
Gives the user access to various configuration options for local access, remote services,
etc.
Tape Drives
Then you can reboot to single-user mode by going to t...
... need of recovery is to try and start the
instance. Do this by issuing the oninit command with no options. If it works, it just returns the
prompt to you. You also could see one of two errors.
curtis ... 433
records the problem to the online log file.) The error that you receive may look something like
the following:
oninit: Cannot open chunk '/informix/rootdbs.dbf'. errno = 2
A...
... when
attempting to open the database:
ORA-0 031 3: open failed for members of log group 2 of thread 1
ORA-0 031 2: online log 2 thread 1:
'/db/Oracle/b/oradata/crash/redocrash02.log'
ORA-0 031 2: online ... will not open, and the error will
look something like this:
ORA-0 031 3: open failed for members of log group 2 of thread 1
ORA-0 031 2: online log 2 thread 1:
'/db/Oracle...
... drive, 631
Mammoth drive vs., 633
AIX operating system
backup, 32 4
backup and recovery, 32 3 -33 7
block size, hardcoding, 135
blocking factor, 107
cloning 3. 2.x or 4.x system, 33 7
installboot, no equivalent ... a commercial backup product, you have the option
of putting the stacker into random-access mode and allowing the backup product to control
it. (Control of automa...