0
  1. Trang chủ >
  2. Kỹ Thuật - Công Nghệ >
  3. Kĩ thuật Viễn thông >

Volume 09 - Metallography and Microstructures Part 1 pps

Volume 09 - Metallography and Microstructures Part 1 pps

Volume 09 - Metallography and Microstructures Part 1 pps

... low-carbon steel. Specimens were rough polished on 1- m diamond and finish polished for 4 h on 0. 1- m Al2O3 suspended in a 2 :1 mixture of propylene glycol and water. Fig. 57: using a 40-g ... on 1- m diamond on a synthetic suede short-nap cloth. Fig. 51: results of polishing on 1- m diamond on cotton drill. All specimens were abraded on a fixed-abrasive lap before polishing. As-polished. ... 648. (b) Specimen 10 0 mm2 (0 .15 in.) in area abraded on a slightly worn 600-grit silicon carbide paper under load of 10 0 g at rubbing speed of 10 5 mm/min. (c) 25-mm ( 1- in.) diam mount on...
  • 100
  • 339
  • 0
Volume 09 - Metallography and Microstructures Part 3 ppsx

Volume 09 - Metallography and Microstructures Part 3 ppsx

... 1 1.0000 1. 000 0-0 .6 310 2 0.7943 0.6 31 0-0 .39 81 3 0.6 310 0.398 1- 0 .2 512 4 0.5 012 0.2 51 2-0 .15 85 5 0.39 81 0 .15 8 5-0 .10 00 6 0. 316 2 0 .10 0 0-0 .06 31 7 0.2 512 0.063 1- 0 .0398 8 0 .19 95 0.039 8-0 .02 51 ... (NL)i Diameters of particles, mm 4 0.007 5-0 . 010 0 19 0. 010 0 5 0. 010 0-0 . 012 5 13 0. 012 5 Substitution in Eq 34 gives: 1/ 26663 419 13() (10 ²7.5² )10 (12 .5 10 ² )10 419 13 10 25900043.7556.25viNmmππ+−−−=−−−=−= ... A/Amax Sections per mm2, (NA)i 1 0.063 1- 0 .05 01 1.000 0-0 .6 310 10 4 2 0.050 1- 0 .0398 0.6 31 0-0 .39 81 16 1 3 0.039 8-0 .0 316 0.398 1- 0 .2 512 253 747 7470 Green Fig. 22 Fig....
  • 100
  • 181
  • 0
Volume 09 - Metallography and Microstructures Part 7 ppsx

Volume 09 - Metallography and Microstructures Part 7 ppsx

... Fig. 11 Fig. 12 Fig. 13 A-286 (AISI 660), solution annealed 1 h at 980 °C (18 00 °F) and aged 16 h at 720 °C (13 25 °F), then air cooled and creep tested to rupture. Fig. 11 : tested 713 1 h ... Eng. Q., Vol 11 , Nov 19 71, p 1- 1 1 51. D.R. Muzyka, Controlling Microstructure and Properties of Superalloys Via Use of Precipitated Phases, ASM Met. Eng. Q., Vol II, Nov 19 71, p 1 2-2 0 52. ... solutioning, and decreased hardness. Compare with Fig. 11 0 and 11 1. Glyceregia. 10 0× Fig. 11 3 Waspaloy (42 HRC), solution annealed 4 h at 10 10 °C (18 50 °F), water quenched, aged 4 h at 845 °C (15 50...
  • 100
  • 424
  • 0
Volume 09 - Metallography and Microstructures Part 8 ppsx

Volume 09 - Metallography and Microstructures Part 8 ppsx

... metals and brazing alloys ER2 319 Al-6.2Cu-0.30Mn-0 .15 Ti ER4043 Al-5.2Si ER5356 Al-0 .12 Mn-5.0Mg-0 .12 Cr-0 .13 Ti 5456 Al-0.8Mn-5.1Mg-0 .12 Cr R-SG70A Al-7Si-0.30Mg 4047 (BAlSi-4) Al -1 2 Si 4245 Al -1 0 Si-4Cu -1 0 Zn ... Fig. 12 6 and 12 7. Electrolytic etch: 2% CrO3. 400× A240 (A140) Al-8.0Cu-0.5Mn-6.0Mg-0.5Ni 242 (14 2) Al-4.0Cu -1 . 5Mg-2.0Ni 295 (19 5) Al-4.5Cu-0.8Si 308 (A108) Al-4.5Cu-5.5Si 319 ( 319 ) Al-3.5Cu-6.0Si ... A357 (A357) Al-7.0Si-0.5Mg-0 .15 Ti 380 (380) Al-9.0Si-3.5Cu 384 (384) Al -1 2 .0Si-3.8Cu 392 (392) Al -1 9 .0Si-0.6Cu-0.4Mn -1 . 0Mg 413 (13 ) Al -1 2 .0Si 443 (43) Al-5.0Si B443 (43) Al-5.0Si-0.3Cu max...
  • 100
  • 466
  • 0
Volume 09 - Metallography and Microstructures Part 9 pps

Volume 09 - Metallography and Microstructures Part 9 pps

... deformation and roughening. Keller's reagent. 15 0× γβ...
  • 100
  • 204
  • 0
Volume 09 - Metallography and Microstructures Part 11 pps

Volume 09 - Metallography and Microstructures Part 11 pps

... . 10 39 0.3 7-0 .44 0.7 0 -1 .00 0.040 max 0.050 max . . . . . . . . . . . . Resulfurized steels 11 13 0 .13 max 0.7 0 -1 .00 0.0 7-0 .12 0.2 4-0 .33 . . . . . . . . . . . . 11 17 0 .1 4-0 .20 ... 411 8H 0 .1 7-0 .23 0.6 0 -1 .00 0.035 max 0.040 max 0.2 0-0 .35 . . . 0.3 0-0 .70 0.0 8-0 .15 414 0 0.3 8-0 .43 0.7 5 -1 .00 0.035 max 0.040 max 0.2 0-0 .35 . . . 0.8 0 -1 .10 ... 1. 0 0 -1 .30 0.040 max 0.0 8-0 .13 . . . . . . . . . . . . Alloy steels 3 310 0.0 8-0 .13 0.4 5-0 .60 0.025 max 0.025 max 0.2 0-0 .35 3.2 5-3 .75 1. 4 0 -1 .75 . . . 3 310 H 0.0 7-0 .13 ...
  • 100
  • 192
  • 0
Volume 09 - Metallography and Microstructures Part 4 pdf

Volume 09 - Metallography and Microstructures Part 4 pdf

... 11 0 10 25 steel, normalized by austenitizing at 10 95 °C (2000 °F) and air cooling. Coarse grain structure is pearlite (black) in a ferrite matrix. See also Fig. 11 1. Picral. 500× Fig. 11 1 ... 99, 10 0, 10 1, 10 2, 10 3, and 10 4 in the section "Atlas of Microstructures for Carbon and Alloy Steels" in this article. Carbon and Alloy Steels: Metallographic Techniques and Microstructures ... (dark), martensite (light), and ferrite (white). 10 % Na2S2O5. 10 00×. (M. Scott) Fig. 10 9 Steel specimen (Fe-0.22C-0.88Mn-0.55Ni-0.50Cr-0.35Mo) taken 38 mm (1. 5 in.) from the quenched...
  • 100
  • 331
  • 0
Volume 09 - Metallography and Microstructures Part 5 pot

Volume 09 - Metallography and Microstructures Part 5 pot

... from 550 to 17 95 MPa (80 to 260 ksi) and minimum yield strengths from 275 to 14 50 MPa (40 to 210 ksi) for the 14 grades in A 14 8. Figures 15 , 16 , 17 , 18 , 19 , 20, and 21 illustrate microstructures ... (L.L. Bright) Fig. 44 Low-alloy cast steel (0.28C-0.55Mn -1 . 3Si -1 . 00Ni -1 . 5Cr-0.4OMo), normalized at 925 °C (17 00 °F), hardened by water quench from 900 °C (16 50 °F), and tempered at 290 °C (550 ... ksi). Figures 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 , 11 , 12 , 13 , and 14 in the section "Atlas of Microstructures for Carbon and Low-Alloy Steel Castings" in this article show microstructures...
  • 100
  • 592
  • 1
Volume 09 - Metallography and Microstructures Part 6 ppt

Volume 09 - Metallography and Microstructures Part 6 ppt

... 3. 0-5 .0 1. 0 1. 0 0.040 0.030 3. 0-3 .5Cu, 0 .1 5-0 .45Nb + Ta 6 31 (1 7-7 PH) 0 .09 16 .0 0 -1 8.00 6. 5-7 .75 1. 0 1. 0 0.040 0.030 0.7 5 -1 .50Al 633 (AM-350) 0.0 7- 0 .11 16 .0 0 -1 7.00 4.0 0-5 .00 0. 5 -1 .25 ... 0.4Al, 0. 4 -1 .2 Ti 1 5-5 PH 0.07 14 .0 0 -1 5.5 3. 5-5 .5 1. 0 1. 0 0.040 0.030 2. 5-4 .5Cu, 0 .1 5-0 .45Nb + Ta PH1 3-8 Mo 0.05 12 .2 5 -1 3.25 7. 5-8 .5 0 .10 0 .10 0. 010 0.008 2. 0-2 .5Mo, 0.9 0 -1 .35Al, 0.01N Custom ... 0.08 16 .0 0 -1 8.00 10 .0 0 -1 4.00 2.0 1. 0 0.045 0.030 2. 0-3 .0Mo, 0 .10 N 316 L 0.03 16 .0 0 -1 8.00 10 .0 0 -1 4.00 2.0 0.75 0.045 0.030 2. 0-3 .0Mo, 0 .10 N 440A 0.6 0- 0.75 16 .0 0 -1 8.00 . . . 1. 0 1. 0 0.040...
  • 100
  • 362
  • 0
Volume 09 - Metallography and Microstructures Part 10 pot

Volume 09 - Metallography and Microstructures Part 10 pot

... Nickel 200 1. 4 -1 .5 9 -1 0 Nickel 270 1. 5 -1 .8 1 0 -1 2 Duranickel 3 01 1.2 5 -1 .5 8 -1 0 37 mL H3PO4 (conc), 56 mL glycerol, 7 mL H2O Monel 400 0. 9 -1 6-7 Etching. The solutions and conditions ... Murakami's reagent. 10 0× Fig. 8 Mo-41Re rod. Warm swaged from 38-mm (1. 5-in.) diam ingot to 25-mm ( 1- in.) diam. Hydrogen annealed at 16 00 °C (2 910 °F) for 10 min. 275 HV. Equiaxed structure ... H2SO4, and H2O with 3 to 5 drops 30% H2O2. 250× Fig. 3 FS-85 niobium alloy (Nb-28Ta -1 1 W-0.8Zr), 2.8-mm (0 .11 0- in.) thick sheet. Arc melted, hot extruded, warm rolled at 705 °C (13 00...
  • 100
  • 292
  • 1

Xem thêm

Từ khóa: dreamweaver cs5 tutorial how to make a website using photoshop and dreamweaver part 1thiết kế bài giảng sinh học 11 nâng cao tập 1 part 1 ppsxdeveloping web page using html and css part 1cụm di tích chiến thắng bạch đằng ở yên giang – quảng ninh part 1 ppsxbài giảng ứng dụng tin học trong xây dựng part 1 ppsxbài tập tin học đại cương part 1 ppsxNghiên cứu sự biến đổi một số cytokin ở bệnh nhân xơ cứng bì hệ thốngBáo cáo quy trình mua hàng CT CP Công Nghệ NPVNghiên cứu tổ chức pha chế, đánh giá chất lượng thuốc tiêm truyền trong điều kiện dã ngoạiMột số giải pháp nâng cao chất lượng streaming thích ứng video trên nền giao thức HTTPNghiên cứu vật liệu biến hóa (metamaterials) hấp thụ sóng điện tử ở vùng tần số THzđề thi thử THPTQG 2019 toán THPT chuyên thái bình lần 2 có lời giảiGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitGiáo án Sinh học 11 bài 13: Thực hành phát hiện diệp lục và carôtenôitPhối hợp giữa phòng văn hóa và thông tin với phòng giáo dục và đào tạo trong việc tuyên truyền, giáo dục, vận động xây dựng nông thôn mới huyện thanh thủy, tỉnh phú thọPhát triển du lịch bền vững trên cơ sở bảo vệ môi trường tự nhiên vịnh hạ longNghiên cứu, xây dựng phần mềm smartscan và ứng dụng trong bảo vệ mạng máy tính chuyên dùngNghiên cứu về mô hình thống kê học sâu và ứng dụng trong nhận dạng chữ viết tay hạn chếChuong 2 nhận dạng rui roTổ chức và hoạt động của Phòng Tư pháp từ thực tiễn tỉnh Phú Thọ (Luận văn thạc sĩ)BT Tieng anh 6 UNIT 2Nguyên tắc phân hóa trách nhiệm hình sự đối với người dưới 18 tuổi phạm tội trong pháp luật hình sự Việt Nam (Luận văn thạc sĩ)Giáo án Sinh học 11 bài 14: Thực hành phát hiện hô hấp ở thực vậtGiáo án Sinh học 11 bài 14: Thực hành phát hiện hô hấp ở thực vậtĐổi mới quản lý tài chính trong hoạt động khoa học xã hội trường hợp viện hàn lâm khoa học xã hội việt nam