Tài liệu Handbook of Organizational Behavior pdf

Tài liệu Handbook of Organizational Behavior pdf

Tài liệu Handbook of Organizational Behavior pdf

... 982). Loss of control as a stress moderator: The role of control perceptions of job burnout. Jourrlal of Applied Psychology, 81: 123-133. moderators of stress. Journnl of Personalih ... importance of incorporating contextual variables into general models of group effectiveness. We explore the benefits of embracing, in part or in full, the new paradigm of mes...
Ngày tải lên : 15/02/2014, 19:20
  • 410
  • 607
  • 8
Tài liệu Handbook of Mechanical Engineering Calculations P3 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P3 pdf

... combustion and increases the weight of the products of combustion per pound (kilogram) of coal burned. Therefore, the weight of the products of combustion is the sum of the weight of the combustion products ... cu m) of natural gas; 1300 cu ft of air (36.8 cu m) per gal (0.003785 cu m) of No. 2 fuel oil; 1450 cu ft of air (41 cu m) per gal of No. 5 fuel oil; 1500 cu ft...
Ngày tải lên : 17/12/2013, 11:15
  • 24
  • 744
  • 0
Tài liệu Handbook of Mechanical Engineering Calculations P5 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P5 pdf

... conditions of 1800 psia (12,402 kPa) and 1050 Њ F (565.6 Њ C). At exit from the cylinder the steam has a pressure of 500 psia (3445 kPa) and a temperature of 740 Њ F (393.3 Њ C). A portion of this ... more heaters. Plot the percent improvement vs. number of stages of extraction, Fig. 6, to observe the effect of additional heaters. A plot of this type shows the decreasing gains...
Ngày tải lên : 17/12/2013, 11:15
  • 16
  • 616
  • 1
Tài liệu Handbook of Mechanical Engineering Calculations P6 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P6 pdf

... average heat of vaporization of 1000 Btu / lb (2330 kJ / kg) of steam, this exhaust gas flow could generate 8,880,000 /1000 ϭ 8880 lb/h (4032 kg/h) of steam. If oil with a heating value of 145,000 ... types of fuels and the internal-combustion engines using them. Note that where the cost of the fuel is high, the cost of the engine is low; where the cost of the fuel is low, th...
Ngày tải lên : 17/12/2013, 11:15
  • 44
  • 734
  • 0
Tài liệu Handbook of Mechanical Engineering Calculations P9 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P9 pdf

... to the Terms of Use as given at the website. Source: HANDBOOK OF MECHANICAL ENGINEERING CALCULATIONS 9.10 PLANT AND FACILITIES ENGINEERING Related Calculations. When using tables of air-motor ... cool- ing effectiveness of both types of towers are about equal. Data given on cooling towers elsewhere in this handbook can be helpful to the designer in choosing the best type of t...
Ngày tải lên : 17/12/2013, 11:15
  • 44
  • 648
  • 1
Tài liệu Handbook of Mechanical Engineering Calculations P12 pdf

Tài liệu Handbook of Mechanical Engineering Calculations P12 pdf

... procedure is the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Professor of Mechanical Engineering, ... procedure is the work of Norman R. Sparks, Professor and Head, Depart- ment of Mechanical Engineering, The Pennsylvania State University, and Charles C. DiLio, Associate Prof...
Ngày tải lên : 17/12/2013, 11:15
  • 80
  • 512
  • 0
Tài liệu Handbook of Corrosion Engineering P2 pdf

Tài liệu Handbook of Corrosion Engineering P2 pdf

... concentration of oxygen at the head 26 Chapter One Head Coated alloy Tail X Front of head Back of head Direction of propagation Figure 1.10 Illustration of the filament nature of filiform corrosion. 0765162_Ch01_Roberge ... convenient way of representing the rates of oxida- tion and reduction of a given single electrode at equilibrium, when no loss or gain is experienced by...
Ngày tải lên : 22/12/2013, 23:17
  • 20
  • 405
  • 2
Tài liệu Handbook of Machine Design P37 pdf

Tài liệu Handbook of Machine Design P37 pdf

... di where Z 2 = number of teeth of larger pulley Zi = number of teeth of smaller pulley d 2 = pitch diameter of larger pulley di = pitch diameter of smaller pulley Datum length: / ... safety, since the probability of sudden failure of a complete belt set is very small. The uniformity of initial tensions and speed ratios of all belts of mult...
Ngày tải lên : 20/01/2014, 01:20
  • 40
  • 440
  • 1

Xem thêm

Từ khóa: